Version 1.0 1.0 版
1Introduction Sprinter 150M_CN/250M_CN - 1.0.0en EN ZH Ur Manual (English)
1.Introduction Purcha Congratulations on the purcha of a new Leica Geosystems elec-tronic level.
It is designed to make levelling works easier and quicker on any construction site.Product This manual contains important safety direc-tions as well as instructions for tting up the product and operating it. Refer to "1
2. Safety Directions" for further information.Read carefully through the Ur Manual before you u the product.Product identification The model and the rial number of your product are indicated on the type plate.Enter the model and rial number in your manual and always refer to this information when you need to contact your agency or Leica Geosystems authorized rvice workshop.Type: ____________Serial no.: ____________Validity of this manual This manual is valid for Sprinter 150M_CN/250M_CN.
Trademarks All trademarks are the property of their respective owners.
Available documentation
Symbols
The symbols ud in this Manual have the following meanings:
ƽDANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or s
erious injury.ƽWARNING Indicates a potentially hazardous situation or an unintended u which, if not avoided, could result in death or rious injury.ƽCAUTION Indicates a potentially hazardous situation or an unintended u which, if not avoided, may result in minor or moderate injury and / or appreciable material, financial and environmental damage.)Important paragraphs which must be adhered to in practice as they enable the product to be ud in a technically correct and efficient manner.Name Description Sprinter 150M_CN/250M_CN Ur Manual All instructions required in order to operate the product to a basic level are contained in this Ur Manual. Provides an overview of the system together with technical data and safety directions.
2Instrument Components Sprinter 150M_CN/250M_CN - 1.0.0en Table of Contents
1.
<12.
23.
34.
45.
Set .106.
<107.
Data 298.
Check & 309.3210.Operation Messages.. (33)
11.Care and Transport (35)
12.Safety Directions (36)
13.Technical Data (43)
14.International Warranty, Software Licence Agreement (46)
46 2.Instrument Components Container Contents Sprinter, batteries (4x), allen key, ur manual, strap, CD-ROM (incl. DataLoader), USB cable.
a)Horizontal fine motion screw b)Battery compartment incl. phone jab interface for USB cable c)Circular level d)Gunsight e)Focusing knob
f)Handle g)Eyepiece h)LCD display i)Ba plate j)Levelling footscrew
Accessories
Tripod, aluminum staff (region dependant), fibre glass staff (to achieve 0.7 mm accuracy with Sprinter 250M_CN). (Optional: sunshade, 4 rechargeable batteries and charger)
3.Measurement Preparations
3.1Change Battery
Inrt 4 AA dry cells according to the positive and negative signs as indicated on the holder.
)Always replace with a complete battery t!
)Do not u old and new batteries together.
)Do not u batteries from different manufacturers or batteries of different types.
3.2Set-up Instrument
Levelling
•Set up the tripod. Extend the legs to a suitable length and ensure that the tripod head is approximately level. Tread the tripod shoes firmly into the ground to ensure stability.
•Mount the instrument on the tripod by screwing the tripod screw onto the ba of the instrument.
•U the three levelling foot screws to center the circular bubble in order to level the instrument.
Eyepiece Adjustment
Point the telescope to a uniform light surface such as a wall or a piece of paper. Turn the eyepiece until the cross hairs are sharp or distinct.Target Image Focusing
U the gunsight to aim the objective lens at the staff. Turn the hori-zontal fine motion screw until the
staff is nearly centered in the field of view and then turn the focusing knob to focus on the staff. Ensure that staff image and reticle are sharp or distinct.
Power ON
The instrument is ready to measure.
)Technical hints:
•First check and adjust the electronic and optical line-of-sight errors, then the circular level on the instrument and then the staff: before starting work in the field, after long storage periods, after long transportation.
•Keep the optics clean. Dirt or condensation on the optics can limit measurements.
•Before starting work, let the instrument adjust to the ambient temperature (approx. 2 minutes per °C of temperature differ-ence).
•Avoid measuring through window panes.
•Staff ctions have to be fully extended and properly cured. •Touching the upper third of the tripod, can damp vibrations at the instrument due to wind.
•U the lens hood to cover the objective when backlight disturbs. •Evenly illuminate the measuring area of the staff with a flashlight or spotlight in darkness.
3
Measurement Preparations Sprinter 150M_CN/250M_CN - 1.0.0en
