Material Safety Data Sheet (MSDS) Page : 1/5 Product Name : KEPITAL F10-XX+, F15-XX+, F20-XX+, F25-XX+, F30-XX+, F40-XX+, FV-XX+, TX-XX+
Revision Date : Jul 17, 2012 (Re. 12) This Safety Data Sheet is according to Regulation EC No. 1907/2006
Product Name: KEPITAL F10-XX+, F15-XX+, F20-XX+, F25-XX+, F30-XX+, F40-XX+,
FV-XX+, TX-XX+
“XX” : may be replaced with two digits(01,02,03,11,20,21,30,31,33,34,40,52,63, etc)
“+”: may be attached to alphabets (A, F, H, HK, L, M, N, O, S, T, LOF, etc)
Product Description: Polyoxymethylene Copolymer, Acetal copolymer
Product Usage (Restriction) Extrusion, Injection (Except usage)
Company Identification KOREA ENGINEERING PLASTICS Co., Ltd.
450, KONGDUCK-DONG, MAPO-GU, SEOUL, KOREA
Tel) 82–2–707-6831~9
Manufacturer Identification KOREA ENGINEERING PLASTICS Co., Ltd. Ulsan plant
84, GOREA-RO, JANGSAENGPO, NAM-GU, ULSAN 680-050, KOREA
Tel) 82-52-279-7830~4
Classification of the substance or mixture
No need for classification according to GHS criteria for this product.
Label elements & Statements of hazard
The product does not require a hazard warning label in accordance with EC Directives.
Other hazards
manlyNFPA(SCALE 0-4 ) : Health =1, Flammability =1, Physical Hazard=0
(Note : The ratings are determined by Korea Engineering Plastics Co., Ltd.)
Composition: INGREDIENT CAS NUMBER Content(%)
Ba Resin 24969-26-4 > 97
Other Additives - < 3
Formaldehyde 50-00-0 < 0.1
This is a polymeric material. And hazardous constituents are wetted by the polymer system, and therefore, prent no likelihood of exposure under normal conditions of processing and handling. This product is considered hazardous under OSHA Regulations due to the relea, if overheated, of
formaldehyde, an OSHA regulated material.
Inhalation
Pellets is not likely to be inhaled due to physical form. When gas and fumes from molten plastics is inhaled, remove to fresh air. Seek medical attention if breathing difficulties occur.
Skin Contact
If hot and molten polymer or hot vapors contact skin, cool rapidly with cold water. If polymer is stuck to skin, do not remove, and ek medical attention. And allow adhered polymer to come off naturally. Removal of adhered polymer may result in
more tissue damage than if polymer is allowed to come off over them.
Eye Contact Immediately flush eyes with plenty of water for at least 15mimuts. Seek medical attention if discomfort persists. Ingestion If a significant quantity has been swallowed, give two glass of water to dilute. Seek medical attention.
Most important symptoms and effects, both acute and delayed
No significant reaction of the human body to the product known.
Note to Physicians
This product is esntially inert and nontoxic. However, if it is overheated or burns, gas such as carbon monoxide and formaldehyde may be relead. Tho expod to off-gas may need to have their arterial blood gas and carboxyhemoglobin levels checked. If the carboxyhemoglobin levels are normal and the exposure occurred in an enclod space, asphyxia (carbon dioxide replacing oxygen) is a possibility. Formaldehyde is a respiratory irritant gas. If patients may have inhaled high concentrations of irritating fumes they should be monitored for delayed ont pulmonary edema.
绯闻女孩演员Suitable extinguishing media
Carbon dioxide, Dry Chemical, Foam or Water spray.
Special hazards arising from the substance or mixture
Hazardous Product of Combustion : Carbon monoxide and Carbon dioxide,Formaldehyde vapors
Hazardous of fire, explosion :
adobe air是什么- Overheating may result in relea of formaldehyde, which may irritate the eyes, skin and respiratory tract.
- Ba resin dust/powder has a US Bureau of Mines relative dust explosion hazard rating of vere.
Firefighting Instructions
Firefighters should wear lf-contained breathing apparatus and full fire-fighting turn-out gear(bunker gear). Keep personnel removed from and unwind of fire. Water should be ud to keep fire-expod containers cool. Product burns with a very hot, but very faint blue flame. Water, foam and dry chemical may cau damage to electrical equipment.
Personal precautions, protective equipment
-
High risk of slipping due to leakage/spillage of product. In Ca of Spill or Leak, sweep or gather up spills and place in proper container for recovery or disposal. Keep unnecessary people away, isolate hazard area and deny entry.
- Information regarding personal protection can be found in ction 8.
Environmental precautions
No special environmental precautions necessary.
Methods and material for containment and cleaning up
Move to the approved place bad on the disposal regulation.
Handling
Do not handle hot or molten material without appropriate protective equipment. Maintain good houkeeping in work areas.
Do not exceed recommended process temperature to minimize relea of decomposition products. Do not smoke in areas where polymer dust is prent. Appropriate measures should be taken to control the generation and accumulation of dust during conveying and processing operations.
Storage
Store in well-ventilated area away from heat and sunlight. Keep Container clod to prevent contamination.
Engineering Controls
Local Exhaust : Recommended when appropriate to control employee exposure to dust or process vapors.
General : May not be adequate as the sole means to control employee exposure.
Protective Equipment
Eyes Safety eyewear recommended
Skin
When thermal or melt processing, wear long pants, long sleeves, well insulated gloves, and face shield when there is a chance of contact.
Inhalation
A NIOSH approved respirator is recommended if there is a possibility of dust generation above permissible exposure limits
or that decomposition vapors may be generated.illumina
Exposure Guidelines
Operations involving grinding and machining of parts should be reviewed to assure that particulate levels are kept below recommended standards. Formaldehyde is a hazardous degradation product.
Ingredient Agency Value
Formaldehyde PEL (OSHA ) TWA - 0.75 ppm, ; STEL 2ppm
TLV(ACGIP) Ceiling 0.3ppm
Nuisance/Inert Dust PEL (OSHA ) 15 mg/cu m(total)
5 mg/cu m (respirable)
Nuisance Particulates TLV(ACGIP) 10 mg/cu m (total)
3 mg/cu m (respirable)
Physical Form :Solid / Pellets
Odor : Slight, specific
Odor threshold :No data available
pH Value :Not applicable
Melting Point :165 deg C (329 deg F)
beg的用法
Boiling Point and Range : Not applicable (Solid)
Flash Point : > 93 deg C ( > 200 deg F) by Tag Clod Cup Method.
Evaporation rate: Not applicable
Inflammability: No data available
Explosion range : No data available
Vapor Pressure :< 0.001mm Hg
Water Solubility : Negligible < 0.1%
Relative vapor density : Not applicable
Specific Gravity : 1.38 - 1.42
Partitioning coefficient n-octanol/water (log Kow): No data available
Ignition temperature : 350 deg C (662 deg F)
Decomposition temperature : > 240 °C
Viscosity : Refer to the grade data sheet
Molecular weight : Not applicable
Chemical Stability : Stable under normal conditions of u and storage.
美行思远Condition to Avid
Maintain polymer melt temperature below 230 deg C.(446 deg F). Avoid prolonged exposure at or above the recommended processing temperature.
Incompatibility with Other Material
Strong acids, ba (decompos forming formaldehyde) and oxidizing materials. At melt temperatures, acetal resins are incompatible with halogenated polymer such as PVC, PVDC and any elastomers containing halogenated polymers.
Decomposition
Decomposition of this material depends on the length of time expod to elevated temperatures and may be accelerated by contaminants, pigments and other additives.
Hazardous Decomposition Products : Trioxane, Formaldehyde and Formic acid.
Hazardous Polymerization : Will not occur.
No specific information available on the product.
Ecotoxicity : No specific information available on the product.
Environmental Information : This material is considered to be non-biodegradable.
Disposal
Recycling is encouraged. Dispo in accordance with all applicable regulations. This product, as shipped, in not a RCRA hazardous waste under prent EPA regulations.
UN No. : Not classified as a dangerous good under transport regulations. (UN RTDG)
Shipping information : Not applicable
Transport hazardous grade : Not applicable
Container grade : Not applicable
Marine Pollution : Not applicable
Safety measure for transport : Not applicable
- Fire : No available data
- Leak : No available data
a place near by
U.S. Regulations
TSCA : All the ingredients are listed in the TSCA Inventory or are compliant with the TSCA polymer Exemption Rule.
SARA :This product does not contain any toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning and Community Right-to-Know Act of 1986 and of 40 CFR 372.
Labeling According to EEC Directives : Not subject to labeling.
Germany Regulations : Not classified according to German “Hazardous Substance” regulations.
EU regulation : Not contain materials listed in ;
WEEE (Waste on Electrical and Electronic Equipment): EU-Directive 2002/96/EC
RoHS(Restriction of Hazardous Substances in electrical and electronic equipment) : EU-Directive 2002/95/EC
Directive 2003/11/EC: Restriction (ban) of Pentabromodiphenylether and octabromodiphenylether
Source
- Hazardous Substances Data Bank (HSDB)
- UN RTDG (Recommendations on the Transport of Dangerous Good) Rev.17
- International Uniform Chemical Information Databa (IUCLID)
Revision : 12 (July 17th 2012)
Disclaimer
This product is not intended for u in medical applications involving permanent implantation in the human body.
proposal是什么意思
The information contained herein is bad on the prent state of our knowledge. We don’t suggest or guarantee that any hazards listed herein are the only ones that exist. Korea Engineering Plastics Co., Ltd. makes no warranty of any kind concerning the safe u of this material in your process or iisraeli
韩语发音规则n combination with other substances. Effects can be aggravated by other materials and this material may aggravate the effects of other materials. Urs have the sole responsibility to determine the suitability of the materials of any u and the manner of u contemplated. Urs must meet all applicable safety and health standards.
- The End of MSDS -
