W i d e b a n d P o w e r A m p l i f i e r R W P 05040-10
Typical Specifications
V CC = +28V; T = 25℃; Z S = Z L = 50Ω
No
Item
Conditions全国一卷语文答案
Min
Typ
Max
Unit
ctu
1 Bandwidth 20 1000 MHz
2 Small Signal Gain
36 38 40 dB 3 Gain Variation vs Temperature -20°C to 60°C
-2.0
+2.0
dB
4
Gain Variation vs Frequency
±1 ±2 dBpp
20MHz to 300 MHz
44 46 300 MHz to 600 MHz 42 45 5 P 3dB 600 MHz to 1000 MHz
41 43 dBm
20MHz to 300 MHz 51 53 300 MHz to 600 MHz 46 48 6
OIP3 @ Po = +33dBm
(1MHz Tone spacing, CW 2-Tone) 600 MHz to 1000 MHz
43
45
dBm 7 Input Return Loss -12 -7 dB
8
Output Return Loss
-8 -5 dB 9 2nd Harmonic suppression CW 1-tone
@Po = +30dBm, Freq 400MHz
-
34 -31 dBc
platelets
10 Supply Voltage Vcc(=Vds) 27.5 28 30 V
11 Quiescent Current Consumption 1.9 2.1 2.3 A 12 Current Consumption @ P 3dB CW 1-tone
2.5
3.2
A
On : TTL "Low"
13
On/Off Switching Time Off : TTL "High"(300mA@Disable) 3 5 uS On : TTL “Low”(Enable) 0 0.5 14 Shut Down or Switch On/Off TTL Voltage
Off : TTL “High”
2.5
5
5.5
V
Product Features
Application
GaN on SiC Broadband High Power Amplifier 20 to 1000MHz Operation Bandwidth Small Signal Gain 36dB min. 40W Typical. P3dB
HF/VHF/UHF Broadband PA Broadcasting PA
Description
The power amplifier module is designed for Broadcasting, Telecommunication, Medical and Other markets. Operating frequency range is from 20MHz to 1000MHz
Gallium Nitride on SiC technology is ud and attached on an aluminum sub carrier. Full in/out matc
hing for broadband performance is already applied.
Improved thermal handling by patented technology.
Package : DP-75
Environmental Characteristics
No Item Min Typ Max Unit
Temperature -20 +60 °C
1 Operating
Temperature -40 +105 °C
2 Storage
socks怎么读3 Vibration MIL-STD-810G Method 514.6 ANNEX C
Absolute Maximum Ratings
production
No Item Rating Unit
Temperature +85 °C Flange
1 Operating
2 Input RF Power +15 dBm
3 Supply
Voltage +30 V Value 3 : 1 @all load pha
4 Load
Mismatch
* Input Signal Condition : CW 1-Tone
Ordering Information
No Part Number Package
1 RWP05040-10 Pallet
2 RWP05040-1H Module asmbled with RWP05040-10
* RWP05040-1H is a SMA connectorized housing version of RWP05040-10. Electrical parameters are all same as RWP05040-10.
For more information, plea contact RFHIC
RWP05040-10 Typical Performance @ 25℃
Frequency
P1dB
P3dB Current@P1dB
Current@P3dB
2nd Harm
OIP3 (30dBm/Tone)
(MHz)
(dBm)
(dBm)
(A)
(A)
@30dBm(dBc) (dBm)
independence day20 44.0 45.3 2.04 2.23 -34.4 53.2 100 44.2 46.2 2.07 2.44 -33.8 53.1 200 44.7 46.5 2.20 2.67 -32.6 53.1 300 44.5 46.1 2.21 2.56 -32.3 52.8 400 44.0 46.1 2.10 2.66 -31.8 52.4 500 43.1 45.1 1.90 2.25 -31.3 50.4 600 40.7 43.2 1.89 2.49 -31.9 49.2 700 40.8 44.7 1.92 2.60 -33.9 46.3 800 40.8 43.7 1.85 2.45 -35.0 45.2 900 41.5 44.2 1.95 2.54 -41.5 45.6 1000 43.2 44.3
2.63
2.53
natasha bedingfield
缘分有take2
-44.6
45.3
OIP3
Gain
P3dB
2nd Harmonics
1. This product is designed to be ud for broadband amplification. Heat generation is higher when there is no RF signal in the device. Therefore, the worst ca scenario is when there is
我叫金三顺插曲no RF signal, and the amplifier is “on” with current draw. The temperature must be calculated properly. Ca temperature must maintain below 85°C.
Right side drawing notes how to u a temperature monitoring function to protect against overheating.
2. Thermal Grea or Metal Thermal Interface Materials are recommended for heat dissipation. An example would be spreading thermal grea on the bottom of the device.
Precautions
Input Return Loss
Output Return Loss
Package Dimensions (Type: DP-75)
(Unit : mm/[inch], Tolerance : ±0.2/[.008])
How to connect the amplifier to a target PCB
Method-І (with Pin)Method-ΙІ (without Pin) - If you cut out the pin
哈利波特1中文版
Pin Description
Pin No Port Name Function
IN RF Input
1 RF
2 Vcc(+28V) DC Supply
Down(+5V) Shut Down @ TTL High, Enable @ TTL Low
3 Shut
ON/OFF Disable @ TTL High (Switch Status : Off)
4 Switch
Monitor 0.75V @ 25℃, Scale : 10mV/℃ (Accuracy : ±3℃)
5 Temp
OUT RF Output
6 RF
* Terminal Pin Information : ASK206091,AA (Acethink, Pin) , ASK20556,AA-1(Acethink, Pin Socket)
* Recommended Screw Torque : ±1 using SEMS M3 10mm Bolt
Note :
RFHIC Corporation (RFHIC) rerves the right to make changes to any products herein or to discontinue any product at any time without notice. RFHIC do not assume any liability for the suitability of its products for any particular purpo, and disclaims any and all liability, including without limitation conquential or incidental damages. The product specifications herein expresd have been carefully checked and are assumed to be reliable. However, RFHIC disclaims liability for inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purcha orders. RFHIC products are not intended for u in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer us or lls such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC and its directors, officers, stockholders, employees, reprentatives and distributors harmless against any and all claims arising out of such u. RFHIC’s liability under or arising out of damages, claims of whatsoever kind and nature which RFHIC products could cau shall be limited in amount to the net purcha price of the products sold to buyer by RFHIC.
