Rev: NC
Date: 01OCT00
TITLE: INSTALLATION PROCEDURE FOR
SL850 AND SL854 PULL-UP TYPE INSERTS
Page 1 of 11
1.0 INTRODUCTION:
1.1This Technical Sales Bulletin describes installation procedure of SL850 Blind-Threaded and
SL854 Thru-Threaded Pull-up type inrts. The procedures u the SLPGA850 Power tool
and SLT850S300 hand tool.
1.2The two types of inrts are designed to be ud on aluminum or mild steel structure, solid
accu是什么意思aluminum or mild steel sheet/plate and some aluminum or mild steel tubing.
Below are examples of each ries and styles available:
SL850
Blind-Threaded
Flush Style Flat Style
SL854
Thru-Threaded
Flush Style Flat Style
2.0INSERT SELECTION:
When lecting a pull-up inrt plea refer to the latest revision of SL850 and SL854 sales drawings. Attention needs to be given to:
•Type- Blind or Thru- Threaded
•Material- Alloy Steel or Stainless Steel
•Thread size- Inch or Metric
•Head Style- Flush or Flat, Self-Locking or Non-Locking
•Sheet Thickness- It is very important the inrt matches the appropriate sheet thickness •Finish- Required finish must be specified
Rev: NC
石家庄翻译学院Date: 01OCT00
TITLE: INSTALLATION PROCEDURE FOR
SL850 AND SL854 PULL-UP TYPE INSERTS
Page 2 of 11
3.0SHEET PREPARATION:
3.1The following illustrations are examples of the required installation hole and countersink.
Plea e table I for installation hole and countersink size for a given inrt thread size.
3.2Care must be taken when drilling the installation hole to minimize “Burrs” on the “Exit” side
of sheet. This will insure that the inrt will “Clinch” properly to the backside of the sheet.
Flat Installation Flush Installation
Rev: NC
Date: 01OCT00
TITLE: INSTALLATION PROCEDURE FOR
SL850 AND SL854 PULL-UP TYPE INSERTS
Page 3 of 11 4.0SLPGA850 POWER TOOL INSTALLATION:
This ction describes installation procedure of SL850 Blind-Threaded and SL854 Thru-Threaded Pull-up type inrts using the SLPGA850 Power tool.
Note:This TSB is to ud in conjunction with the latest revision of Shur-Lok’s SLD850 data
sheets.
5.0SLPGA850 POWER TOOL SETUP:
POWER TOOL
AS SUPPLIEDbecau we can
5.1Power tool kits includes:
1-Power tool
普特英语网2-No Guide Locknut (1 spare)
1-Set of Three Open-Ended Wrenches
1-Set of Three Allen Wrenches德语词典
1-Manufacturers operating instructions
No guides and mandrels must be order parately. Plea e sheet 2 of SLD850 data sheets, table I for proper no guide and mandrel for your inrt thread size.
Rev: NC
Date: 01OCT00
TITLE: INSTALLATION PROCEDURE FOR
SL850 AND SL854 PULL-UP TYPE INSERTS
Page 4 of 11
5.2 a) Unthread and remove power tool no casing to expo spindle and adapter nut.
b) Using open-ended wrenches supplied with power tool remove adapter nut for spindle.
c) Inrt mandrel into spindle then replace adapter nut onto spindle. Tighten with open-
ended wrenches and replace power tool no casing.
d) Thread one (1) no guide locknut onto no guide until the locknut bottoms-out.怎样查四级成绩
e) Thread no guide into power tool no casing. Thread until no guide locknut
aga
bottoms-out to power tool no casing.
POWER GUN NOSE ASSEMBLY
Rev: NC
Date: 01OCT00
TITLE: INSTALLATION PROCEDURE FOR
SL850 AND SL854 PULL-UP TYPE INSERTS
Page 5 of 11
6.0INSERT INSTALLATION:
6.1 Connect power tool to source compresd air.
Note: For proper power tool operation, consult manufacturers operating instructions
supplied with kit.
赛车总动员3
a)The stroke of power tool must be adjusted. This is accomplished by turning the rear
casing (black rubber portion of power tool). To do this turn the casing “IN”
(clockwi) until there is very little stroke (movement) of the mandrel when actuated.malaguena
Note: It is recommended to perform the adjustments on a sample plate of the same
thickness before installing into working structure.
slutsb)Hold inrt to threaded portion of mandrel.
c)Inrt threaded portion of mandrel into the threaded portion of inrt.
d)While holding inrt, push into mandrel.
Note: Do not pull trigger of power tool, it will automatically thread mandrel to
inrt.