Relea:
20.10.2008
Features
Typical Applications
Multimodal HDPE Very High stiffness
High stiffness Blown Film
pear的音标
Good dart drop resistence
with paperlike quality
Excellent processing and bubble stability Carrier Bags, counter bags, wrapping film
Additive Package
Thermal Slip yes
no
Resin Properties
Method Value (1)Unit Density (23°C, ba resin)ISO 1183-1/A 0,957 g/cm³
Melt Flow Rate 190°C/5kg ISO 11330,40 g/10 min Melt Flow Rate 190°C/21,6kg ISO 113312,0 g/10 min FRR (MFR 21,6kg / MFR 5kg)
ISO 1133
30
Physical and Application Properties (4)Film rating (gels, visual inspection 4)LB test method ≤3(rank)Dart drop impact, 20 µm Film ASTM D 1709250g
bubble stability 4)
LB test method < 2(rank)
(1) typical average values, not to be construed as specifications. Customers should confirm suitabilit
y and results by their own tests.
(3) 60kg/h, BUR 4:1, 900mm NL, T= 220 °C, die Ø120mm, 1.0 mm gap (4) 1 ≤ rank ≤ 6, 1 = best, 6 = worst
Processing
recommended melt temperature on processing
180 - 230°C
High Density PE for Blown Film
Lyondellball cannot anticipate all conditions under which this information and our products or the products of other manufacturers in combination with our products may be
ud. Lyondellball accepts no responsibility for results obtained by the application of this information or the safety and suitability of our products alone or in combination with other products. Urs are advid to make their own tests to determine the safety and suitability of each such product or product combination for their own purpos. Unless otherwi agreed in writing, Lyondellball lls the products without warranty, and buyers and urs assume all responsibility and liability for loss or damage arising from handling and u of our products, whether ud alone or in combination with other products. The property values quoted are typical of European produced grades only and do not constitute a specification. Unless specifically indicated, the grades mentioned are not suitable for applications in the pharmaceutical/medical ctor.
Licen Grade ACP9255plus
Features
Typical Applications
Very High stiffness Top Quality PE 100 pressure pipes Very High ESCR gas and water supply @ higher pressures
High toughness Additive Package
Thermal Slip yes
no
Resin Properties
Method Value (1)
Unit Density (23°C, ba resin)ISO 1183-1/A 0,950g/cm³Melt Flow Rate 190°C/5kg ISO 11330,23g/10 min Melt Flow Rate 190°C/21,6kg
ISO 1133
6,4
g/10 min
Physical and Application Properties Modified Charpy impact strenght aFM 0°C 2)ISO 179/1eA (mod.)> 8,5 kJ/m²ESCR (FNCT, 4 MPa, 80°C, 2% NP9 *)
ISO 16770> 1000 h Hydrostatic pressure test 12.4 MPa, 20°C 5)ISO 9080> 200 h Hydrostatic press
ure test 5.5 MPa, 80°C 5)ISO 9080> 500h Hydrostatic pressure test 5.0 MPa, 80°C 5)ISO 9080> 1000h Rapid crack propagation (RCP, S4) 6)
ISO 13477> 10bar Notch Pipe Test (pipe 110mm SDR11, 80°C, 9,2 bar)
ISO 13479> 500 h Water a)DIN 53715
< 0,02 %OIT (210° C)
EN 728 / 11357-6> 30 min Odor treshold 4)EN 1622 / EN 1420 < 1,5 (rank)Inhomogenities
< 0,03 mm²
(1) typical average values, not to be construed as specifications. Customers should confirm suitability and results by their own tests.*) NP9: Arkopal N100, Igepal BC9
Version:20.10.2008
High Density PE for pipe
6) one lot per year by external institute
For certified applications like AENOR, LNE, BP-Chemicals, only VE=A is allowed. a ) After 6 months the remaing quantity will be moved to quality stocks. The water 4) additionally one lot per 3 months by TZW 5) test at 12.4 MPa on one lot per month (3 speciems) until 500h, 5.5 MPa every 6 months until 25000h content will be measured again and a new quality classification will be done 2)
one lot per week by QS
Features Typical Applications
High stiffness High Quality PE 80 pressure pipes
High ESCR High toughness Additive Package
Thermal Slip yes
no
Resin Properties
Method Value (1)Unit Density (23°C, ba resin)ISO 1183-1/A 0,949 g/cm³ipsw
Melt Flow Rate 190°C/5kg ISO 11330,43 g/10 min Melt Flow Rate 190°C/21,6kg
ISO 1133
九九句法9
g/10 min
Physical and Application Properties
try的用法Modified Charpy impact strenght aFM 0°C 2)ISO 179/1eA (mod.)> 7,0 kJ/m²ESCR (FNCT, 4 MPa, 80°C, 2% NP9 *)ISO 16770> 100h
Hydrostatic pressure test 4.6 MPa, 80°C
ISO 9080
>5000 h Rapid crack propagation (RCP, S4) 6)
ISO 13477
> 5 bar Notch Pipe Test (pipe 110mm SDR11, 80°C, 8 bar)ISO 13479
> 500 h Water a)DIN 53715
< 0,02 %OIT (210° C) EN 728 / 11357-6
> 30 min Odor treshold 4)EN 1622 / EN 1420
< 1,5 (rank)Inhomogenities < 0,03 mm²
(1) typical average values, not to be construed as specifications. Customers should confirm suitability and results by their own tests.*) NP9: Arkopal N100, Igepal BC9
Version:20.10.2008
High Density PE for pipe
6) one lot per year by external institute
For certified applications like AENOR, LNE, BP-Chemicals, only VE=A is allowed. a ) After 6 months the remaing quantity will be moved to quality stocks. The water 4) additionally one lot per 3 months by TZW content will be measured again and a new quality classification will be done 2)
one lot per week by QS
Relea:同等学力英语考试
20.10.2008
Features
Typical Applications High molecular weight HDPE
Universal Container grade
Excellent balance stiffness to ESCR Larger jerry cans excellent impact strength Volume 1 - 150 liters
Additive Package
Thermal Slip yes
no
Resin Properties
Method Value (1)Unit Density (23°C, ba resin)ISO 1183-1/A 0,952 g/cm³
virtually
Melt Flow Rate 190°C/5kg ISO 11330,28 g/10 min Melt Flow Rate 190°C/21,6kg ISO 11336,5 g/10 min FRR (MFR 21,6kg / MFR 5kg)
两分钟英语自我介绍
ISO 1133
23
Physical and Application Properties Tens. Mod. (23°C, v = 1mm/min, Sec.)ISO 527-21050MPa Tensile Impact strength (23°C, notched)ISO 8256-1A 295kJ/m²Tensile Impact strength (-30°C, notched)ISO 8256-1A 130kJ/m²Charpy Impact strength (-30°C, notched)ISO 179-1/1eA 20kJ/m²ESCR (FNCT, 4 MPa, 80°C, 2% NP9 ²)ISO 1677020h Swell ratio
185%
(1) typical average values, not to be construed as specifications. Customers should confirm suitability and results by their own tests.
(2) NP9: Arkopal N100, Igepal BC9
Processing
recommended melt temperature on processing
180 - 220°C
Licen Grade ACP5331A
High Density PE for Large Blow Moulding
Lyondellball cannot anticipate all conditions under which this information and our products or the p
roducts of other manufacturers in combination with our products may be ud. Lyondellball accepts no responsibility for results obtained by the application of this information or the safety and suitability of our products alone or in combination with other products. Urs are advid to make their own tests to determine the safety and suitability of each such product or product combination for their own purpos. Unless otherwi agreed in writing, Lyondellball lls the products without warranty, and buyers and urs assume all responsibility and liability for loss or damage arising from handling and u of our products, whether ud alone or in combination with other products. The property values quoted are typical of European produced grades only and do not constitute a specification. Unless specifically indicated, the grades mentioned are not suitable for applications in the pharmaceutical/medical ctor.
Relea:
20.10.2008
Features
Typical Applications
featuredHigh stiffness
Bottles from a few ml to 10 liter
Excellent balance stiffness to ESCR Leisure, Toys
good flow ability Consumer Packaging
Additive Package
如何搭配冬装Thermal Slip yesagonize
no
Resin Properties
Method Value (1)Unit Density (23°C, ba resin)ISO 1183-1/A 0,958 g/cm³
Melt Flow Rate 190°C/2.16kg ISO 11330,35 g/10 min Melt Flow Rate 190°C/5kg ISO 11331,2 g/10 min Melt Flow Rate 190°C/21,6kg ISO 113322 g/10 min FRR (MFR 21,6kg / MFR 5kg)
ISO 1133
18
Physical and Application Properties Tens. Mod. (23°C, v = 1mm/min, Sec.)ISO 527-21320MPa Tensile Impact strength (-30°C, notched)ISO 8256-1A 65kJ/m²Charpy Impact strength (-30°C, notched)ISO 179-1/1eA >4kJ/m²ESCR (FNCT, 4 MPa, 80°C, 2% NP9 ²)ISO 16770>3,6h Swell ratio
145%Film rating (gels, visual inspection 4)
LB test method ≤ 4,5(rank)
(1) typical average values, not to be construed as specifications. Customers should confirm suitability and results by their own tests.
(2) NP9: Arkopal N100, Igepal BC9(4) 1 ≤ rank ≤ 6, 1 = best, 6 = worst
Processing
recommended melt temperature on processing
180 - 220°C
Licen Grade ACP5831D
High Density PE for Small Blow Moulding
Lyondellball cannot anticipate all conditions under which this information and our products or the products of other manufacturers in combination with our products may be ud. Lyondellball accepts no responsibility for results obtained by the application of this information or the safety and suitability of our products alone or in combination with other products. Urs are advid to make their own tests to determine the safety and suitability of each such product or product combination for their own purpos. Unless otherwi agreed in writing, Lyondellball lls the products without warranty, and buyers and urs assume all responsibility and liability for loss or damage arising from handling and u of our products, whether ud alone or in combination with other products. The property values quoted are typical of European produced grades only and do not constitute a specification. Unless specifically indicated, the grades mentioned are not suitable for applications in the pharmaceutical/medical ctor.
