东莞钜升塑胶有限公司
LTD..
DG Jusheng Plastic and Electronic Productcts LTD
结构2D图技术标注参考规范
文件编号：保密等级：保密
文件类型：管理办法有效期：3年
页数：1/2版本: 1.0
编制日期：2006-12-15开始执行日：2006-12-17
目录索引
01.Latchmake sure
02.Antenna
03.PCBA outline drawing
04.Battery
05.1Lens(注塑)
05.2Lens(CNC)
06.1Audio cover
06.2RF_switch_cover
07.1Shielding
07.2Spring
08.Metal dome
09.Stop TPU
10.Light guide
11.Fpcba
12.1金属装饰件
12.2Logo
12.3Plating plastic
12.4Electroform
13.1双面胶
13.2泡棉
13.3绝缘片
14.1Keypad asm
14.2keypad rubber
14.3Keypad电镀键帽
14.4Keypad数字键
计算机专业英语15.1外观漆喷漆图
16.Housing part drawing
17.Housing Asmbly
18.Explode
01.Latch
考研英语单词技术要求（Notes）:
1.材料：POM Dupont500，用100%原材料;
Material:POM Dupont500,u100%raw material.
pian
2.尺寸：图面尺寸用于检验零件外形、功能和装配;
未注圆角R0.05，未注脱模斜度1度，未注尺寸依照Pro/e3D Data;
标有环形圈：每批次出货均需检查；Qualify时需要做CP/CPK;
Dimension:Specified dimensions in the drawing are ud to check outside shape,function and as
mbly;
Unspecified round:R0.05mm;Unspecified draft angle:1degree;
Unspecified dimensions refer to Pro/e3D model data;
Specified dimensions with marked ring are critical dimensions,need to be checked every shipment,and must do CP/CPK check in the Qualification stage.
3.公差：未注公差依照图面公差表;
Tolerance:Unspecified tolerance should comply with tolerance table in the drawing;
4.外观：成品清洁、无杂质、无划伤、缩水及其它瑕疵;
飞边及分型线段差≤0.03mm；顶杆痕≤0.05mm；浇口凸出≤0.10mm;
穴号应刻在模具上，标志不得高于表面;
外观皮纹:VDI24;
Appearance：Product should be tidy and purity,no nick,no shrinkage and other blemish;
Galling should be less than0.03mm;Ejector rod mark should be less than0.05mm;
gate trim should be less than0.10mm;
suicidesCavity number shall be located low on the surface.Appearance require:VDI24.
5.检测须满足钜升质量标准:《部品检验标准_注塑件_x.x_xxxxxx》
Product should be satisfied with quality standard of Jusheng:《部品检验标准_注塑件_x.x_xxxxxx》
02.Antenna
1.材料：见图，用100%原材料;
1.Material:Refer to the drawing table,in original color and with100%raw material.
2.尺寸：图面尺寸用于检验零件外形、功能和装配;
未注圆角R0.05，未注脱模斜度1度，未注尺寸依照Pro/e3D Data;
标有环形圈的是重点尺寸，每批次出货均需检查,Qualify时需要做CP/CPK；
2.Dimension:Specified dimensions in the drawing are ud to check outside shape,function and asmbly;
Unspecified round:R0.05mm;Unspecified draft angle:1°;Unspecified dimensions refer to
Pro/e3D model data;
返回索引目录
Specified dimensions with marked ring are critical dimensions,need to be checked every shipment,and must do CP/CPK check in the Qualification stage.
3.公差：未注公差依照图面公差表;
3.Tolerance:Unspecified tolerance should comply with tolerance table in the drawing;
4.外观：成品清洁、无杂质、无划伤、缩水及其它瑕疵;
飞边及分型线段差≤0.03mm，顶杆痕≤0.05mm；浇口凸出≤0.05mm;
穴号应刻在模具上，标志不得高于表面;
外观皮纹：抛光
4.Appearance：Product should be tidy and purity,no nick,no shrinkage and other blemish;
Galling shall be less than0.03mm,ejector rod mark shall be less than0.05mm,gate trim shall be less than0.05mm.Cavity number shall be located low on the surface.Surface shall be smooth.
5.电气性能依照规格书：violet1-Antenna SPEA-05-02-18.pdf。
5.Electro performance shall be according to spec:violet1-Antenna SPEA-05-02-18.pdf
6.喷涂:
范围：见喷漆图；
油漆颜色及色差:△E≤1；
喷漆厚度：底漆8-10um；UV10-12um；
油漆硬度:2H，500gf；
油漆耐磨:RCA300cycles；
油漆附着力：百格实验，脱落面积≤3%.
6.Coating:
Painting range:refer to the painting drawing.
Paint color and aberration:△E≤1
Paint thickness:BC8-10um；UV10-12um；
Paint hardness test:2H，500gf
Paint abrasion test:RCA300cycles
Paint peeling test:area of peeling≤3%.
7.包装与运输：零件独立包装，放入托盘对应的凹穴，托盘层堆放入纸箱;
7.Package and Transport:Product should be packaged independent,and lay in tray,finally put the trays in the paper box;
8.检测须满足钜升质量标准：《机模信赖度测试标准_VX.X.pdf》
8.Product should be satisfied with quality standard of Jusheng:
《机模信赖度测试标准_VX.X.pdf》
03.PCBA drawing
1.图面尺寸用于检验PCB外形、功能和装配;
Specified dimensions in the drawing are ud to check PCB outside shape,function and asmbly;
2.重点尺寸：标有环形圈，每批次出货均需检查；Qualify时需要做CP/CPK；
返回索引目录
Specified dimensions with marked ring are critical dimensions,need to be checked every shipment;
and must do CP/CPK check in the Qualification stage;
3.未注公差参照图面公差表;
Unspecified tolerance should comply with tolerance table in the drawing;
could4.包装：产品按一定数量密封包装，需防污防潮。
Package of product should be quantitative,aled,dustless and dampproof.
04.BATTERY
1.电池后盖与电芯之间用双面胶粘贴;
Using double adhesive between battery rear cover and cell;
2.电池前后盖超焊后，前后壳配合周边严禁溢料;
焊接牢固可靠，不许有虚焊，封装后厚度方向的变形量不超过0.15mm;
After ultrasonic welt,burr is forbidden around battery;
The welding should be fastness and dependable,no fal-welding,deformation in heignt should be less than0.15mm.
3.尺寸：图面尺寸用于检验零件外形、功能和装配;
标有环形圈的是重点尺寸，每批次出货均需检查；Qualify时需要做CP/CPK;
Dimension:Specified dimensions in the drawing are ud to check outside shape,function and asmbly;Specified dimensions with marked ring are critical dimensions,need to be checked every shipment,and must do CP/CPK check in the Qualification stage.
4.BATT_CONN需镀金，镀层厚度不小于0.5um;
Batt_conn must be gilt,coating thickness must be no less than0.5um
盐雾试验：35℃，5%氯化钠溶液，48小时后无腐蚀;
Salt fog test:In35¡ãC48h5%NaCl salt fog concentration,it can not be rusty after48hs 跌落试验：1.5米高度，6面3棱1角分别跌落，水泥地面，
两轮共20次跌落，电池功能正常，外观无明显损伤;
1.5m drop test:6faces(Left Back Right Bottom Top Front),3edges1corner,1drop per face,edge;corner,2cycles,battery function must be normal,have no obvious damages in apperance.
5.电气性能依照文件：《Li+电池SPEC》VX.X;betroth
Electric function refer to:《Li+BATTERY SPEC》VX.X
6.包装与运输：电池用塑料袋和纸盒独立包装。
Package and Transport:Product should be packaged independent,and lay in tray,finally put the trays in the paper box;
7.检测须满足钜升质量标准：
Product should be satisfied with quality standard of Jusheng:《部品检验标准_注塑件》V X.X;《GB_T18287_2000蜂窝电话用锂离子电池总规范》
crushing>英语词典大全
返回索引目录
>one fifth
