1 Power Electronic Concepts
Power electronics is a rapidly developing technology. Components are tting higher current and voltage ratings, the power loss decrea and the devices become more reliable. The devices are also very easy tocontrol with a mega scale power amplification. The prices are still going down pr. kVA and power converters are becoming attractive as a mean to improve the performance of a wind turbine. This chapter will discuss the standard power converter topologies from the simplest converters for starting up the turbine to advanced power converter topologies, where the whole power is flowing through the converter. Further, different park solutions using power electronics arealso discusd.
1.1 Criteria for concept evaluation
The most common topologies are lected and discusd in respect to advantages and drawbacks. Very advanced power converters, where many extra devices are necessary in order to get a proper operation, are omitted.
1.2 Power converters
cee
Many different power converters can be ud in wind turbine applications. In the ca of using an induc
tion generator, the power converter has to convert from a fixed voltage and frequency to a variable voltage and frequency. This may be implemented in many different ways, as it will be en in the next ction. Other generator types can demand other complex protection. However, the most ud topology so far is a soft-starter, which is ud during start up in order to limit the in-rush current and thereby reduce the disturbances to the grid.go right ahead
1.2.1 Soft starter
The soft starter is a power converter, which has been introduced to fixed
speed wind turbines to reduce the transient current during connection or disconnection of the generator to the grid. When the generator speed exceeds the synchronous speed, the soft-starter is connected. Using firing angle control of the thyristors in the soft starter the generator is smoothly connected to the grid over a predefined number of grid periods. An example of connection diagram for the softstarter with a generator is prented in Figure1.
推特是什么意思
Figure 1. Connection diagram of soft starter with generators.
The commutating devices are two thyristors for each pha. The are connected in anti-parallel. The relationship between the firing angle (﹤) and the resulting amplification of the soft starter is non-linear and depends additionally on the power factor of the connected element. In the ca of a resistive load, may vary between 0 (full on) and 90 (full off) degrees, in the ca of a purely inductive load between 90 (full on) and 180 (full off) degrees. For any power factor between 0 and 90 degrees, w ill be somewhere between the limits sketched in Figure 2.
Figure 2. Control characteristic for a fully controlled soft starter.
When the generator is completely connected to the grid a contactor (Kbyp) bypass the soft-starter in order to reduce the loss during normal operation. The soft-starter is very cheap and it is a standard converter in many wind turbines.
1.2.2 Capacitor bank
shampooing
For the power factor compensation of the reactive power in the generator, AC capacitor banks are us
ed, as shown in Figure 3. The generators are normally compensated into whole power range. The switching of capacitors is done as a function of the average value of measured reactive power during a certain period.
2011年上海高考作文neocomimiFigure 3. Capacitor bank configuration for power factor compensation in
a wind turbine.祈使句反义疑问句
The capacitor banks are usually mounted in the bottom of the tower or in the
divideintonacelle. In order to reduce the current at connection/disconnection of capacitors a coil (L) can be connected in ries. The capacitors may be heavy loaded and damaged in the ca of over-voltages to the grid and thereby they may increa the maintenance cost.
1.2.3 Diode rectifier
The diode rectifier is the most common ud topology in power electronic applications. For a three-pha system it consists of six diodes. It is shown in Figure 4.
Figure 4. Diode rectifier for three-pha ac/dc conversionpogo是什么意思
The diode rectifier can only be ud in one quadrant, it is simple and it is not
possible to control it. It could be ud in some applications with a dc-bus.
1.2.4 The back-to-back PWM-VSI
The back-to-back PWM-VSI is a bi-directional power converter consisting of two conventional PWM-VSI. The topology is shown in Figure 5.
To achieve full control of the grid current, the DC-link voltage must be boosted to a level higher than the amplitude of the grid line-line voltage. The power flow of the grid side converter is controlled in order
to keep the DC-link voltage constant, while the control of the generator side is t to suit the magnetization demand and the reference speed. The control of the back-to-back PWM-VSI in the wind turbine application is described in veral papers (Bogalecka, 1993), (Knowles-Spittle et al., 1998), (Pena et al., 1996), (Yifan & Longya, 1992), (Yifan & Longya, 1995).
Figure 5. The back-to-back PWM-VSI converter topology.
1.2.4.1 Advantages related to the u of the back-to-back PWM-VSI
The PWM-VSI is the most frequently ud three-pha frequency converter. As a conquence of this, the knowledge available in the field is extensive and well established. The literature and the available documentation exceed that for any of the other converters considered in this survey. Furthermore, many manufacturers produce components especially designed for u in this type of converter (e.g., a transistor-pack comprising six bridge coupled transistors and anti paralleled diodes). Due to this, the component costs can be low compared to converters requiring components designed for a niche production.
A technical advantage of the PWM-VSI is the capacitor decoupling between the grid inverter and the generator inverter. Besides affording some protection, this decoupling offers parate control of the two inverters, allowing compensation of asymmetry both on the generator side and on the grid side, independently.
>allin什么意思
