错误代码 | Error Message 错误信息 | Solutions 解决方案 |
ERROR 20 错误20 ERROR 200 错误200 | Input Paper Sensor was not triggered - Paper may be jammed at the nsor.输入文件是不触发传感器-纸可以挤在传感器。 Remove toner cartridge for better access to jammed paper.取出卡住的纸张硒鼓为更好地进入。 | Paper not being picked up check paper tray & pickup rollers文件不被拾起检查纸盒及皮卡辊 Replace rollers if worn smooth or cracked如果更换轧辊磨损或破裂顺利 |
ERROR 21 错误21 | The exit nsor was not made in time after the input nsor as made.传感器的出口并没有在时间后，输入传感器作为的。 | |
ERROR 22 错误22 | The exit nsor was not unmade in time.该传感器是没有的取消退出时间。 | |
ERROR 23 错误23 | Jam at the duplex unit. Paper is either not leaving the duplex entry nsor in time or not making or unmaking the duplex exit nsor in time.塞问题的双面打印单元。纸是不是没有离开传感器时进入或双工不制造或unmaking传感器及时双工退出。 See “Duplex” on page 2-16看到“双面”2-16页 | |
Error 24 错误24 | The defined paper size is too short to print data as formatted.该定义的纸张大小是太短，打印格式的数据。 | |
Error 25 错误25 | Input nsor made at wrong time.输入传感器是在错误的时间。 May be due to the paper feeding manually while motors running and previous page in path.可能是由于手动送纸电机运行时的路径，并在以前的页面。 | |
Error 26 错误26 | Duplex unit is installed but paper tray is not nd.复式单位已安装但纸托盘没有感觉到。 | |
Error 27 错误27 | Envelopes/paper loaded are wrong size.信封/纸装是错误的大小。 | Load correct size 加载正确的大小 |
Error 28 错误28 | Input nsor not made after pick attempt.输入传感器没有作出选择后尝试。 Tray is empty or not installed, paper jam in entry throat, or printer is requesting a manual feed.托盘为空或没有安装，纸张在进入喉咙堵塞，是请求或打印机手动送纸。 | |
Error 29 错误29 | The output bin nsor has not been unmade.See “Output Bin Sensor” on page 2-22.本传感器输出尚未unmade.See“输出斌感应器”页2-22。 | |
Error 30 错误30 | 30 Top Cover Open or Print Cartridge Missing Make sure the spring-mounted pin on the printhead shroud is installed 30顶盖打开或打印墨盒失踪确保春季装针打印头安装裹尸布 properly and that it is detected by the ramp on the print cartridge as the cover clos.正确的实施，它是检测墨盒打印的坡道上作为封面关闭。 The pin should enter the tower on the HVPS and depress the cover switch.该引脚应进入回乡证塔上，并抑制盖开关。 | |
Error 31 错误31 | Error code 31 is displayed when the top front cover is clod and a defective print cartridge is detected. 31错误代码时显示关闭前盖顶和墨盒是一个有缺陷的检测。 It may take the printer 10-20 conds to determine if the print cartridge is defective. Note: This error indicates the printer was able to read the cartridge ID, but the ID did not pass the verification test.它可能需要10-20秒的打印机，以确定是否有缺陷的墨盒。 注意：此错误表示打印机墨盒能够读取身份证，但没有通过身份验证测试。 | Remove and reinstall print cartridge.删除并重新安装打印墨盒。 Shop for Lexmark print cartridges 店内利盟墨盒 |
Error 32 错误32 | 32 Wrong Print Cartridge installed The installed print cartridge is not supported by the Optra printer. 32墨盒安装错误安装的打印机墨盒不支持Optra。 | |
Error 37 错误37 | 37 Insufficient Collation Memory Memory is too full to collate the print job. 37没有足够的内存整理内存太满整理打印作业。 | |
Error 38 错误38 | 38 Memory Full Memory ud to store pages is full. 38记忆全部内存用来存储页面已满。 To verify that the printer recognizes all the installed memory, go to the ur menus and print the “Print Menus” test page.要验证所有已安装的打印机识别记忆，到用户的菜单和打印“打印菜单”测试页。 Make sure the memory shown on the printout matches the installed memory.确保打印输出上显示内存的匹配安装的内存。 | Install more memory安装更多的内存 Simplify print job简化打印作业 Delete fonts, macros and other data stored in RAM删除字体，宏和其他数据存储在RAM |
Error 39 错误39 | Page too complex to print.To verify that the printer recognizes all the installed memory, go to the ur menus and print the “Print Menus” test page.页面过于复杂，print.To验证确认所有已安装的打印机的内存，请用户菜单和打印“打印菜单”测试页。 Make sure the memory shown on the printout matches the installed memory.确保打印输出上显示内存的匹配安装的内存。 | |
Error 43 错误43 | Font card format not supported by字体卡格式不支持 printer.打印机。 | |
Error 44 错误44 | Defective font card installed in font slot.有缺陷的字体安装在字体卡插槽。 | |
Error 47 47个错误 | 47 Font Card Removed While Printing Printer needs data on removed card. 47字体卡取下打印机打印数据卡需要拆除。 | |
Error 52 错误52 | Flash Full - Not enough flash memory for data requested to be stored.闪光灯全部-没有足够的闪存请求的内存数据被存储。 | |
Error 53 错误53 | Unformatted or Defective Flash - Flash problem at POR or while未格式化的或有缺陷的闪光-闪光的问题，而在葡萄牙或 attempting to write.试图写入。 | |
Error 54 错误54 | 复利计算Serial Error - Framing or parity error on rial.串行错误-帧校验错误或串行。 | |
Error 58 错误58 | Duplex Not Attached Duplex is electrically connected but no longer mechanically attached, and printer top cover is clod.双工不附加复式是电动机械连接，但不再附加，并关闭打印机顶盖。 | |
Error 59 错误59 | Duplex Cover Open Top cover of duplex unit is nd open.双面盖打开顶盖的复式单位是感觉到开放。 | |
Error 62 错误62 | Disk Full Not enough disk space for data that has been requested to be written to disk.磁盘已要求全部不足够的磁盘空间数据写入到磁盘。 | |
Error 63 错误63 | Unformatted or Defective Disk The printer will ignore a disk it ns as defective. Run the Quick Disk Test.未格式化的或有缺陷的磁盘，打印机将忽略一个磁盘上的感官有缺陷的。运行快速磁盘测试。 If the test fails, the disk is defective or the data on track1 is bad.如果测试失败，是有缺陷的磁盘或track1数据是坏的。 If the Quick Disk Test pass but the disk does not work, run the Disk Test/Clean (2 hr. test).如果测试通过快速的磁盘，但磁盘没有工作，运行磁盘测试/清洁（2小时。测试）。 Replace the disk if instructed by the operator panel.如果替换的磁盘操作面板指示。 | |
Error 7X 错误7倍 | Network Card Codes The ur codes are documented in various network card ur manuals.网络卡码这些用户代码用户手册中记录各种网络卡。 See “Network Wrap Tests” on page 23.见“网络裹测试”第23页。 | |
Error 80 80个错误 | Network Card Codes The ur codes are documented in various network card ur manuals.网络卡码这些用户代码用户手册中记录各种网络卡。 See “Network Wrap Tests” on page 23.见“网络裹测试”第23页。 | |
Error 80 80个错误 | Printer has reached 200,000-300,000* prints without maintenance count ret. 打印机打印已达到20-30万*无需维护计数复位。 It is necessary to replace the fur asmbly, transfer roller, and charge roll at this interval to maintain the print quality and reliability of the printer. 要更换定影大会，转移辊，充电辊在此区间保持打印质量和打印机的可靠性。 Shop for Lexmark Maintenance kits 维修车间的利盟包 * This is a model dependent interval *这是一个新型的从属区间 | Install maintenance kit and ret maintenance message安装维修保养工具包和复位信息 Purcha Lexmark maintenance kits购买利盟维修工具包 How did we do? 怎么办呢？ |
Error 82 Photo Developer Cartridge Exhausted 错误82照片墨盒开发力竭 | The Photo Develper (OPC belt cartridge) has reached the end of it's life and must be replaced.该照片Develper（OPC的带盒）已达到它的生命结束的，必须更换。 Press "GO" to clear message and temporarily continuepromote是什么意思按“走出去”，以明确的信息，暂时继续 | Install安装 OPC Belt/Photo Developer OPC的皮带/图片开发 |
Error 84 Transfer 传递错误84 Drum 鼓 Exhausted 疲惫 | The Transfer drum has reached the end of it's life and must be replaced. May require rvice technician鼓的转移已达到它的生命结束的，必须更换。可能需要维修技术人员 Press "GO" to clear message and temporarily continue按“走出去”，以明确的信息，暂时继续 | Install 安装 Transfer 转让 Drum Unit 硒鼓 |
Error 88 错误88 | Toner Low Toner nsor detects low toner.碳粉低碳粉传感器检测低碳粉。 | |
Error 122 错误122 | Fur Error - Problem in the fur, not heating, heating to quickly or too hot. 定影错误-定影问题的，不加热，加热迅速或太热。 Perform fur rvice check.执行定影服务检查。 Can also be LVPS or system board.也可以LVPS或系统板。 Replace fur asmbly更换定影大会 | Replace Fur 更换定影 Lexmark Fur 利盟定影 |
Error 230 错误230 | Paper Jam - Check Duplex卡纸 - 检查复式 The paper is most likely jammed in the Duplex Unit.该文件是最有可能在双工单位卡住。 Remove the duplex front cover to access the jam area.拆下前盖复式访问果酱地区。 If the paper is jammed in the rear of the duplex, replace the duplex front cover and open the duplex rear door. If the paper is not如果纸张卡在后方的双面，取代双面打开前盖和双工后门。如果文件不是 jammed in the duplex unit, then it may be jammed in the rear of the printer. Open the printer rear door to access the jam.挤在复式单位，则可以在打印机堵塞的后方。打开后门进入打印机的卡纸。 | Remove jammed media取出卡住的媒体 How did we do? 怎么办呢？ |
Error 24X 错误24倍速 | Paper Jam - Check Tray "X"卡纸 - 检查托盘的“X” Primary: Paper is jammed around Tray 小学： 纸是托盘周围挤满 X (X=tray 1 thru 5). X（十托盘= 1 5）通过。 Try opening Tray X. 尝试打开托盘十 If the tray is difficult to remove, then you may have to remove the tray above or below tray X to remove the jammed pages. 如果托盘是很难去除，那么您可能需要删除或低于上述托盘托盘X以取出卡住的页面。 Secondary: When this message is displayed, do not remove accumulated sheets during the jam clearance procedure as the printer will not reprint the removed sheets. 中学： 当此消息显示，不累积张表中删除转载拆除果酱清关程序的打印机不会。 Also, if the accumulated sheets are removed, the portion of the job printed after the jam will not be stapled. 此外，如果累计表被删除，果酱部分印后的工作不会被装订。 | Remove jammed media取出卡住的媒体 |
Error 250 错误250 | Paper Jam - Check MP Feeder Paper is jammed in the multipurpo feeder.卡纸-检查国会议员直属纸业接驳卡在多功能。 | Remove jammed media取出卡住的媒体 |
Error 90X 错误90X | Software Error Unrecoverable software error.软件错误无法恢复的软件错误。 If one of the errors appeared during POST, or while the printer was idle (not printing or receiving data), or while trying to print one of the internal test pages, replace the system board.如果出现错误，其中一个在POST期间，或在该打印机空闲（不打印或接收数据），或在尝试打印一个网页的内部测试，更换系统板。 If the error appeared while nding a job from the host to the printer, turn the printer off, then turn it on and try again.如果错误出现，而发送工作从主机到打印机，关闭打印机电源，然后打开它，然后再试一次。 | |
Error 901 错误901 Engine Flash发动机闪光 | Indicates the Flash with the system code program is defective指示程序闪存系统代码有缺陷 | Replace System Board替换系统板 Request Quote 请求报价 |
Error 914 错误914 DC Pick Motor - No Encoder Feedback 直流电动机选择-无编码器反馈 | Check the integrated paper tray, tray 1, for paper loading problems.检查综合纸托盘，托盘1，装纸的问题。 sizeofReload the paper and do a power on ret.重新装入纸张和做复位的权力。 Check paper nsor flag for restricted movement or damage.检查移动或损坏纸张传感器国旗的限制。 Check connecting cables for continuity.检查电缆连接的连续性。 If cables, connectors and connections are good replace asmblies listed.如果电缆，连接器和连接好取代集会上市。 | Replace the Autocompensator Assy. 替换Autocompensator总成。 Replace System Board 替换系统板 Request Quote 请求报价 |
Error 917 错误917 | Check the transfer roller for toner buildup, surface damage to the roller, oil, or other contaminants on the surface of the roller. Replace the transfer roller as necessary.检查墨粉建设转移辊，表面损伤或其他污染物对轧辊表面的，滚子，油。根据需要更换轧辊转移。 Roller is approximately 2" in circumference print defects with this repetitive spacing can be caud by transfer roller problems, on a standard 11" page defect would repeat five times.滚筒约为2“圆周打印此重复间隔缺损所造成的问题可以转让辊缺陷，在标准11”页将重复五次。 The transfer roller is included in the maintenance kit .滚子的转移是包含在维护套件 。 Transfer Roll Error Cannot start rvo operation.传输辊错误无法启动伺服操作。 Verify correct cable connections from the Engine board to the HVPS.验证正确的电缆连接发动机由董事会向回乡证。 Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct.确保有回乡证的连续性辊之间的转移和其联络，更换轧辊，如果转让的连续性是正确的。 If there is no continuity, make sure the HVPS contact returns to its upward limit when depresd, and make sure the left bearing of the transfer roll is making proper contact.如果没有连续性，确保回乡证返回到其向上接触限制时沮丧，并确保转移向左滚转轴承的接触是正确的决策。 Check the left and right transfer roll arm asmbly to make sure it is fastened and locked in the down position if applicable to your machine. There should be zero ohms resistance between the transfer roll shaft and the high voltage supply contact.检查左，右手臂转让辊装配，以确保它是牢固和机械锁在向下位置，如果适用于您的。应该是零欧姆接触电阻辊轴之间的转移和高电压供应。 | Request Quote 请求报价 |
Error 920 错误920 | 920 Fur Error indicates the Fur is below temperature while printing. 920定影的定影是错误显示在打印以下的温度。 The fur, melts or fus the toner to the media and has a heat roller and a pressure roller. The heated roller is heated by a halogen lamp or in some cas a solid state ceramic heating element and is subject to failure.定影，保险丝熔化或碳粉向媒体和有热辊和压辊。加热的加热辊由卤素灯，或在某些情况下，固态陶瓷发热元件，并须要失败的。 A 920 error caud by low line voltage can sometimes be cleared by turning the machine off and then on again.一个920错误造成的低电压线路有时可以清除转动机器关闭，然后再次打开。 Error 920.X and 922.XX may display for a cold fur. 错误920.X和922.XX可能会显示为一个寒冷的定影。 error codes may be cleared by turning the printer on and off and allowing it to complete POR. 有些错误代码可能会被清除转动打印机和关闭，并允许它完成葡萄牙。 In general, fur errors require replacement of the fur as a cost effective repair. 在一般情况下，定影错误需要更换定影的作为一个成本有效的修复。 Fur errors can be from a cold fur or an overheated fur. 定影错误可以从一个冷或过热定影定影。 Newer machines display a sub code to indicate which condition applies. 新机器显示一个代码，以指示哪些子条件适用。 Additional info on X and XX codes available by email . 附加信息编码的X和XX可以通过电子邮件 。 Obrve the lamp through the left near side of the printer. 通过观察左灯打印机附近的一面。 It may be necessary to remove the re drive asmbly to obrve the lamp cycling on and off. 它可能需要删除该驱动器重新组装自行车灯，观察和关闭。 | Fur Pricing 定影定价 How did we do? 怎么办呢？ |
Error 921 错误921 | Fur is below standby temperature when idle. 定影是空闲时的温度低于待命。 Indicates that the fur is below standby temperature表明，定影温度低于待机 when the printer is idle.当打印机处于空闲状态。 | |
Error 922 错误922 | Fur failed to reach standby temperature. 定影没有达到待机温度。 Check the continuity of the fur lamp at the two heavy leads. 检查灯导致在这两个沉重的连续性定影。 If an open circuit, replace the lamp or fur . The fur asmbly is subject to mechanical wear and heat related degradation and is a scheduled replacement item in most machines at between 200K and 350K pages. 如果开路，更换灯泡或定影 。大会的定影是受机械磨损和热降解和相关项目在大多数机器上是一个20万之间的定期更换和350,000页。 The fur is the main part of a printer maintenance kit . 定影是一台打印机的主要部分维护套件 。 The fur can usually be removed with two simple screws and the entire asmbly lifted out. 定影通常可以用两个简单的螺丝拆除，整个国会取消了。 We can email further info if needed for your particular model. It can also be the LVPS (low voltage power supply) or a fu in the power supply on some models. U caution when measuring AC voltages. Check LVPS cable for continuity. 我们可以进一步信息的电子邮件，如果需要为您的特定模式。它也可以是LVPS（低电压电源供应器）或在某些型号的保险丝电源。使用的交流电压测量时要小心。检查的连续性LVPS电缆。 Thermistor Check: hou热敏电阻检查： HOT - J2-1 - J2-2 = 2.5K ohms 热- J2的- 1 - J2的- 2 = 2.5K欧姆 COLD = 150K ohms to 260K ohms 冷= 15万至26万欧姆欧姆 Replace fur asmbly 更换定影大会 | Shop For:店： Lexmark Maintenance Kits 利盟维修工具箱 Lexmark Furs 利盟Fursmiscarriage How did we do? 怎么办呢？ |
Error 923alaways 错误923 | Fur is too hot while printing or when idle.定影太热而印刷或者闲置。 • Short in the thermistor circuit. •短的热敏电阻电路。 • Noisy thermistor signal •热敏电阻噪声信号 • Fur is actually overheating due to •定影实际上是由于过热 hardware faults.硬件故障。 | Most cost effective solution is to replace the fur最具成本效益的解决办法是更换定影 Lexmark Fur Pricing 利盟定影定价 |
Error 924 错误924 | 924 Fur Error - Open circuit detected in thermistor circuit. 924定影错误-热敏电阻开路检测电路。 The thermistor provides feedback on the temperature of the fur roller and when it fails, the fur power is shut off and the fur does not heat up.热敏电阻提供的反馈，定影辊的温度，当它失败时，定影电源关闭，定影不加热。 Replacement of the thermistor is not a cost effective repair, replace fur asmbly.热敏电阻器更换不具有成本效益的修理，更换定影组件。 | Lexmark Fur Pricing 利盟定影定价 |
Error 925 错误925 | A 925 rvice error indicates the wrong fur lamp is installed in the printer and does not match the one stored in the printer code.一个925服务错误表明了错误的打印机定影灯安装在与打印机不匹配一个代码存储在。 Check the fur lamp is the correct type of lamp that should be installed.检查定影灯是安装正确的类型的灯应。 • Verify the line voltage is not exceeding the maximum rating for the printer. •验证线路电压不超过打印机的最高评级。 | |
Error 927 错误927 | Main Fan Stalled, Cartridge Fan or RIP fan stalled,主扇停顿，插装风扇或风扇的RIP停滞不前， Power off and manually spin fan - it should rotate freely.关闭电源，并手动旋转风扇 - 它应该自由旋转。 Check fan connector and cable for loo or damaged connection.检查风扇连接器和连接电缆松动或损坏。 | Check fan for binding or defective bearing - Replace Fan 检查轴承风扇有约束力的或有缺陷的- 更换风扇 How did we do? 怎么办呢？ |
Error 928 错误928 | Era lamp asmbly missing or disconnected擦除灯组装丢失或断开 | |
Error 929 错误929 | The toner nsor is not operating properly, the developer墨粉传感器没有正常运行，开发人员 drive asmbly is not operating properly or the print驱动装置没有正常运行或打印 cartridge is defective. 墨盒是有缺陷的。 | Check developer drive for worn, loo or broken parts.检查驱动器的开发零件磨损，松动或损坏。 Check the wiring harness cable.检查线束电缆。 Check the operation of the toner nsor.检查传感器运作的碳粉。 |
Error 930 错误930 | The wrong printhead is installed.安装了错误的打印头。 Replace with the替换 correct printhead.正确的打印头。 | Replace Printhead Pricing 更换打印头价格 |
Error 931 错误931 | Printhead error - No first sync - check connections at both ends of cable for corrosion or oxidation.喷头错误-没有第一次同步-检查电缆两端的连接在两个腐蚀或氧化。 Reconnect. Can be system board or printhead.重新连接。系统板或可打印头。 | Replace Printhead Pricing 更换打印头价格 |
Error 932 错误932 | Lost hsync No High voltage signal - check connections at both ends of cable for corrosion or oxidation.失去hsync没有高电压信号-检查连接在电缆两端的腐蚀或氧化。 Reconnect. Can be system board or printhead.重新连接。系统板或可打印头。 Requires further measurement需要进一步的测量 The printhead (lar scanner) does not contain any打印头（激光扫描仪）不包含任何 rviceable parts.维修部件。 | Replace Printhead Pricing 更换打印头价格 |
Error 934 错误934 | Printhhead Error - Lost Lock condition Printhhead错误-忘记锁条件 Indicates a problem with the mirror motor circuit in the printhead asmbly or the mirror motor cable to the system board cable or system board asmbly.表明装配问题或系统板的镜子电机电路打印头大会或镜像电机电缆连接到系统板电缆。 | Replace Printhead Pricing 更换打印头价格 |
Error 935 错误935 | Printhead Error - May have sub-codes.喷头错误- 5月有子码。 Mirror motor unable to reach operational speed, various other component level failures indicated by 935.XX镜马达无法达到运行速度，其他各种部件级故障所指出935.XX | 王兆飞博客Check cables, look for chafing or damage to ribbon cable at sharp bends around rear cover.检查电缆，包括寻找摩擦或损伤后在周围弯曲锋利，带状电缆。 Replace printhead, system board or ribbon cable.更换打印头，系统板或带状电缆。 Replace Printhead Pricing 更换打印头价格 |
Error 936 错误936 Error 937 错误937 | Error 936/937 Main Drive Motor, Transport Motor 错误九百三十七分之九百三十六主传动电机，汽车运输 An error with the main drive motor has been nd by the printer 马达与一个错误的主要驱动器已经感觉到了打印机 Optra s 2450 Optra s 1250 Optra s 1650 Optra 2450 Optra s s s 1650 1250 Optra Optra s 2455 Optra s 1255 Optra s 1855 Optra 2455 Optra s s s 1855 1255 Optra Optra s 2420 Optra s 1620 Optra S 1625 Optra s 2420 Optra s 1620 Optra S 1625 Optra Se 3455 Optra t610 Optra t612 Optra硒3455 Optra的T610 Optra t612 Optra t614 Optra t616 Optra T614产品Optra t616 t520 t522 t620 t622 t630 t632 t634 t520 t522 t620 t622 t630 t632 t634 Optra T 640/642/644 Optra Ŧ 640/642/644 Mirror motor not up to speed. 镜电机达不到的速度。 Check printhead, cable, motor, system board. 检查打印头，电缆，电机，系统电路板。 | crispsPower printer off one to two minutes. 打印机电源关闭一到两分钟。 Open doors and covers and remove the toner cartridge. 打开门，覆盖和删除碳粉盒。 Make sure there is no paper jammed in the printer. 确保有是打印机没有纸干扰。 Pay clo attention to the area where the toner cartridge sits. 密切注意的地方坐的碳粉盒。 The main motor is located just to the left of the toner cartridge. 主电机就位于左侧的墨盒碳粉。 If either the 936 error or the 937 error returns after you power on the printer or when you try to print, the printer will require rvice.如果其中的936错误或937错误返回后，你权力在打印机上或当您尝试打印时，打印机将需要服务。 The main motor asmbly may need to be replaced.主电机组装可能需要更换。 |
Error 939 错误939 | RIP Communications Lost RIP协议通信丢失 Controller Engine Communications Lost发动机控制器通信丢失 The controller board and the engine board cannot该控制器板和发动机董事会不能 communicate with one another.彼此沟通。 | POR veral times葡萄牙几次 Check each board检查每个板 for cure ground.为安全理由。 Replace the assys替换assys in the following在下面的 order秩序 1. 1。 Controller Board控制器板 2. 2。 Engine Board发动机委员会 3. 3。 Intterconnect Board Intterconnect局 |
Error 940-943 错误940-943 Color Machines 色机 | Toner Metering Cycle failure CMKY cartridge 碳粉盒计量循环衰竭CMKY 940 = Cyan cartridge 940 =青色墨盒 941 = Magenta cartridge 941 =洋红色墨盒 942 = Yellow cartridge 942 =黄色墨盒 943 = Black cartridge 943 =黑色墨盒 Toner metering cycle (TMC) is where the code and electronics in the printer n an addition of toner in the cartridge developing area. 碳粉计量周期（TMC）的代码是在电子和碳粉在打印机中的意义除了在墨盒开发区。 If the printer is expecting a toner addition cycle but one is not detected, a 94x TMC Error is displayed. 如果打印机碳粉此外周期的预期，但一没有检测到，一个94x丰田错误显示。 | Check the toner metering cam on back of suspect cartridge.检查计量碳粉盒背面的凸轮怀疑。 If not prent check in printer. Replace defective cartridge.如果不是在目前的支票打印机。 替换有缺陷的墨盒。 Check the TMC pin in the cartridge contact error for free non binding movement检查针结合运动的丰田汽车公司在免费的非接触错误的墨盒 If pin does not move freely you may need to replace the contact asmbly.如果脚不自由移动你可能需要更换联络大会。 Contact rvice person联系服务人 |
Error 940 错误940 LV Power Supply低压电源 | Low voltage power supply cross over test failed.低电压电源供应交叉比试验失败。 Check connections to the to interconnect card asmbly.检查连接到互联卡组装。 Check AC power source for noi.检查交流电源的噪声。 | Replace low voltage power supply asmbly.职员翻译 更换低压电源组装。 Request Quote 请求报价 |
947 947 Engine Board 发动机委员会 | Engine board failure发动机故障板 | Replace the Engine Board更换引擎局 Request Quote 请求报价 |
953-954 953-954 NVRAM NVRAM中 Failure 失败 | NVRAM Failure 953: NVRAM Chip Failure NVRAM中失败953：NVRAM的芯片故障 954: NVRAM CRC Failure 954：NVRAM中华润失败 mm是什么意思Optra T 640/642/644 Optra Ŧ 640/642/644 953 - Replace the operator panel board or upper front cover. 953 -替换操作面板电路板或上封面。 954 - Replace the interconnect card. 954 -更换互连卡。 | System Board Pricing 系统板价格 Request Quote 请求报价 |
975-979 975-979 Network Card X 网络卡× | Indicate a network card failure in the specified slot, X=any card in slot 1 or 2. 表明指定的插槽网卡失败中，x =所有卡插槽1或2。 975- Unrecognizable Network Card 975 -无法辨识的网络卡 976- Unrecoverable software error in network card X 976 -在网络卡无法恢复的软件错误X 979- Flash parts failed while programming card X 979 -部分失败的，而编程闪存卡× If the printer is a network model, replace system board 如果打印机是网络模型，更换系统板 | System Board Pricing 系统板价格 |
980-984 980-984 Service 服务 Errors 错误 | Service errors 980 thru 984 <device> can be one of the following: system board, duplex, tray x (1, 2, 3, 4, or 5), envelope feeder or output bin.服务的错误980 984 <设备可以通过下列之一：系统板，双面，托盘×（1，2，3，4或5），信封送纸器或输出桶。 | Service errors 980 thru 984通过984服务的错误980 < device> can be one of the <设备>可以是一 following: system board, duplex,以下内容：系统板，双面， tray x (1, 2, 3, 4, or 5), envelope托盘×（1，2，3，4或5），信封 feeder or output bin.接驳或输出桶。 |
本文发布于:2023-06-20 08:23:49，感谢您对本站的认可！
本文链接：https://www.wtabcd.cn/fanwen/fan/90/151279.html
版权声明：本站内容均来自互联网，仅供演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系，我们将在24小时内删除。
| 留言与评论（共有 0 条评论） |
