Nylon Inrt Locknuts (Inch Series)
A N A M E R I C A N N A T I O N A L S T A N D A R D
Nylon Inrt
Locknuts
(Inch Series)
A N A M E R I C A N N A T I O N A L S T A N D A R D
The Standard is downloaded from Standard Sharing
Date of Issuance:November24,2008
This Standard will be revid when the Society approves the issuance of a new edition.There will be no addenda issued to this edition.
ASME issues written replies to inquiries concerning interpretations of technical aspects of this Standard.Periodically certain actions of the ASME B18Committee may be published as Cas. Cas and interpretations are published on the ASME Web site under the Committee Pages at cstools.asme as they are issued.
ASME is the registered trademark of The American Society of Mechanical Engineers.
This code or standard was developed under procedures accredited as meeting the criteria for Americ
an National Standards.The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate.The propod code or standard was made available for public review and comment that provides an opportunity for additional public input from industry,academia, regulatory agencies,and the public-at-large.
ASME does not“approve,”“rate,”or“endor”any item,construction,proprietary device,or activity.two months
ASME does not take any position with respect to the validity of any patent rights asrted in connection with any items mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable letters patent,nor assumes any such liability.Urs of a code or standard are expressly advid that determination of the validity of any such patent rights,and the risk of infringement of such rights,is entirely their own responsibility.
Participation by federal agency reprentative(s)or person(s)affiliated with industry is not to be interpreted as government or industry endorment of this code or standard.
ASME accepts responsibility for only tho interpretations of this document issued in accordance with the established ASME procedures and policies,which precludes the issuance of interpretations
by individuals.
chama
No part of this document may be reproduced in any form,
虔诚的
in an electronic retrieval system or otherwi,
without the prior written permission of the publisher.
The American Society of Mechanical Engineers
Three Park Avenue,New York,NY10016-5990
Copyright©2008by
THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS
All rights rerved
Printed in U.S.A.
汽车日常保养常识CONTENTSbridesmaid
Foreword (iv)
Committee Roster (v)
Correspondence With the B18Committee (vi)
逃出桃色房间1Introduction (1)
2Reference Standards (1)
3Terminology (1)
4Dimensions (1)
元宵节用英语怎么说
5Nut Designs and Property Grades (1)
6Width Across Flats (1)
7Corner Fill (2)
8Height (2)
9Hex Height (2)
10Threads (2)
11Material,Mechanical,and Performance Properties (4)
12Test Methods (4)
13Grade and Manufacturing Marking (6)
14Inspection and Quality Assurance (6)
15Dimensional Conformance (6)
16Designation (6)
17Workmanship (6)
Tables
1Nut Dimensions (2)
2Proof Loads,Clamp Loads,and Prevailing-Torques for Coar Thread Series
power struggleGrades NE2,NE5,and NE8Nuts (3)
澳洲大学
3Proof Loads,Clamp Loads,and Prevailing-Torques for Fine Thread Series
Grades NE2,NE5,and NE8Nuts (3)
4Chemical Composition Requirements (4)
5Hardness Requirements (4)
iii
The Standard is downloaded from Standard Sharing
FOREWORD
中秋快乐 英语ASME B18.16.6-2008was balloted and approved by the B18Standards Committee and B18 Subcommittee16on April29,2008.The proposal was submitted to the American National Standards Institute and designated as an American National Standard on August25,2008.
iv
