高强螺栓转动能力测试报告 Rotational Capacity Test Report | ||||||||||||||||
项目工号Project No. | 地点Place： | |||||||||||||||
螺栓Bolt Grade: | 螺栓长度Bolt length | |||||||||||||||
试验日期Test date | 螺栓直径Bolt Dia. | |||||||||||||||
转动能力测试Rotational-capacity test | ||||||||||||||||
转动能力测试批号Rotational-capacity lot | 试验方法Test Method | 轴力计Tension measure device □ 标定牌Solid plate □ | ||||||||||||||
生产批号Production lot | ||||||||||||||||
螺栓Bolt | 螺母Nut | 垫圈Washer | ||||||||||||||
试验记录Test Information | ||||||||||||||||
尺子用英语怎么说样Sample 1# | 样deutschSample 2# | |||||||||||||||
初拧达到的拉力 Tension at snug tight | 初拧达到的拉力 Tension at snug tight | |||||||||||||||
| 鸿蒙是什么意思 螺栓要求的最小拉力 Minimum required installation tension | 螺栓要求的最小拉力 Minimum required installation tension | |||||||||||||||
达到最小拉力时的矩值T Measured Torque T | 达到最小拉力时的矩值T Measured Torque T | |||||||||||||||
到最小拉力时的具体拉力P Measured Bolt Tension P | department store到最小拉力时的具体拉力P Measured Bolt Tension P | explicitly | ||||||||||||||
转动圈数 Required rotation | 转动圈数 Required rotation | |||||||||||||||
达到转数后的螺栓拉力 Measured bolt tension at required rotation | 达到转数后的螺栓拉力 Measured bolt tension at required rotation | |||||||||||||||
试验结果判定Test Results | ||||||||||||||||
质量要求Quality Requirements | 样Sample 1# | 样Sample 2# | ||||||||||||||
1) T≤0.25P（D÷12）=963.4N.M | ||||||||||||||||
2达到转数后的螺栓能否达到所要求的1.15倍设计最小拉力值45kips(200KN)。 Is the measured bolt tension at required rotation > 1.15 x RIT? | hanna | 钟道隆 | ||||||||||||||
3）达到所要求的转动角度之前螺栓是否断裂或螺纹损伤？ Did asmbly break or threads strip before reaching required rotation? | Yes(Asmbly fails) No | Yes(Asmbly fails) regularityNo | ||||||||||||||
英语网站导航4）松开螺栓并检验螺栓螺纹和螺母Disasmble and examine threads on bolt and nut: A-有无变形？Signs of shear failure? B-有无剥离？Signs of stripping? C-有无扭曲？Signs of twisting? | A | Yes(Asmbly fails) No | Yes(Asmbly fails) No | |||||||||||||
B | Yes(Asmbly fails) No | Yes(Asmbly fails) No | ||||||||||||||
C | Yes(Asmbly fails) No | Yes(Asmbly fails) No | ||||||||||||||
结论coronerConclusion | 合格Accepted 不合格Rejected | |||||||||||||||
Statement: This report for the items are in conformance to AREMA Capter 15 ction 3.2.14. | ||||||||||||||||
检验员Inspector | 日期Date | |||||||||||||||
本文发布于:2023-06-17 13:18:27，感谢您对本站的认可！
本文链接：https://www.wtabcd.cn/fanwen/fan/90/148250.html
版权声明：本站内容均来自互联网，仅供演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系，我们将在24小时内删除。
| 留言与评论（共有 0 条评论） |
