lotion是什么意思AS/NZS 4665.1/Amdt 1/2009-02-27
STANDARDS AUSTRALIA/STANDARDS NEW ZEALAND
Amendment No. 1
to
AS/NZS 4665.1:2005
Performance of external power supplies
Part 1: Test method and energy performance mark
REVISED TEXT
The 2005 edition of AS/NZS 4665.1 is amended as follows; the amendments should be inrted in the appropriate places.
SUMMARY: This Amendment applies to the Preface, Claus 1.1 and 1.3 and Appendices A, B and C. Published on 27 February 2009.
Approved for publication in New Zealand on behalf of the Standards Council of New Zealand on 29 January 2009conveys
Preface
In the venth paragraph, delete the cond ntence and replace with the following: R egulatory authorities have advid that it is intended to mandate Part 2 of the Standard (AS/NZS 4665.2:2005) in regulations in Australia and New Zealand no earlier than 1 December 2008, except for marking requirements, which are intended to be mandated no earlier than 1 April 2009.
Clau 1.1
Add a new fourth paragraph as follows:
Power supplies within the scope of AS/NZS 4879 or IEC 61347.2.13 are excluded from the scope of this Standard.
Clau 1.3.3
Replace ‘r.m.s.’ with ‘average’.
Clau 1.3.8
Add a new Clau 1.3.8 as follows:
1.3.8 Family of models—Non ur lectable output voltage
A range of non ur lectable single output models bad on common technically equivalent components (typically switchmode), but each model may have a different output voltage. They may be sold under different brand names or model numbers or both. Each member of the family is included on a single test report and has the same energy performance mark, but may have a different output voltage.
Clau 1.3.9
Add a new Clau 1.3.9 as follows:
1.3.9 Multi-switch model—Ur lectable output voltage
A model with a single output that provides a range of ur lectable output voltages. They may be sold under different brand names or model numbers or both. Test reports may include one or more models having the same energy performance mark.
AMDT No. 1 FEB
2009 AMDT No. 1 FEB 2009
AMDT No. 1 FEB
2009
AMDT No. 1 FEB 2009
AMDT No. 1 FEB 2009
L i c e n s e d t o M s Y u n L i o n 12 A p r i l 2012. P e r s o n a l u s e l i c e n c e o n l y . S t o r a g e , d i s t r i b u t i o n o r u s e o n n e t w o r k p r o h i b i t e d .
Claus 1.3.8 to 1.3.15
Renumber Claus 1.3.8 to 1.3.15 as Claus 1.3.10 to 1.3.17 respectively.
Clau 1.3.18
Add a new Clau 1.3.18 as follows: 1.3.18 Single model(s)
One or more models using technically equivalent components with identical performance specifications having the same output voltage. They may be sold under different brand names or model numbers or both. Test reports may include one or more models having the same energy performance mark.
Claus 1.3.16 and 1.3.17
Renumber Claus 1.3.16 and 1.3.17 as Claus 1.3.19 and 1.3.20 respectively.
Paragraph A1
Add new third and fourth paragraphs as follows:
External power supplies, for Mark V only, with an input power greater than or equal to 100 W shall have a true power factor of 0.9 or greater at 100% of rated load when tested at 115 V, 60 Hz.
Products tested for compliance with Mark V at both 115 V and 230 V shall meet the power factor requirement when tested at 115 V, but not when tested at 230 V.
AMDT No. 1 FEB
2009
AMDT No. 1 FEB 2009 AMDT No. 1 FEB
2009
AMDT No. 1 FEB 2009 L i c e n s e d t o M s Y u n L i o n 12 A p r i l 2012. P e r s o n a l u s e l i c e n c e o n l y . S t o r a g e , d i s t r i b u t i o n o r u s e o n n e t w o r k p r o h i b i t e d .
Table A1
Delete the Table and replace with the following:
TABLE A1
ENERGY PERFORMANCE REQUIREMENTS FOR EACH NUMERAL
No load power consumption
requirements
suddenly
Active mode efficiency requirements
Nameplate output power No load power
Nameplate output power Mark
语泉(P no ) W
cdfs是什么意思
W
(P no ) W
Output specification
Average active mode
efficiency
I Ud if it does not meet any of the following criteria 0 to <1 All ≥0.39 × P no
prospectively
II
0 to <10 10 to ≤250 ≤0.75 ≤1.0 1 to <49 All ≥0.107 × L n (P no ) + 0.39 0 to 1
All ≥0.490 × P no
>1 to 49 All ≥0.090 × L n (P no ) + 0.490
to a maximum of 0.840 III 0 to <10 10 to ≤250
≤0.5 ≤0.75
>49 to 250 All ≥0.840 0 to 1
All ≥0.500 × P no运营管理培训
>1 to 51 All ≥0.090 × L n (P no ) + 0.500 to a maximum of 0.850 IV
0 to <10 10 to ≤250
≤0.5 ≤0.5
>51 to 250
All
≥0.850
AC-AC AC-DC
Output voltage
<6 V and
output current ≥0.550 A ≥0.497 × P no + 0.067 0 to 1
Other models ≥0.480 × P no + 0.140 Output voltage <6 V and
output current ≥0.550 A ≥0.0750 × L n (P no ) + 0.561 0 to <50
≤0.5 ≤0.3
>1 to 49
Other models ≥0.0626 × L n (P no ) + 0.622Output voltage <6 V and
output current ≥0.550 A ≥0.860 V
50 to ≤250 ≤0.5 ≤0.5 >49 to 250
Other models
≥0.870
VI – X Rerved for future u虚荣是什么意思
LEGEND:
P no = nameplate output power of the EUT L n = the natural logarithm (ba e)
AMDT No. 1 FEB 2009
L i c e n s e d t o M s Y u n L i o n 12 A p r i l 2012. P e r s o n a l u s e l i c e n c e o n l y . S t o r a g e , d i s t r i b u t i o n o r u s e o n n e t w o r k p r o h i b i t e d .
Paragraph A2
不要介意的英文1 Inrt a new Clau heading before the first paragraph as follows:
A2.1 General
2 Delete the Note and replace with the following:
NOTE: Numerals VI to X are rerved for future u.
3 Inrt the following after Figure A1:
A2.2 Single performance mark when tested at 115 , 230 and
240 or has a single input voltage If the external power supply complies with the requirements of a single performance mark at both 115 and 230 or has a single input voltage, then the mark can be as shown in Figure A1. If only one mark is applied, then it shall be the lowest mark attained when tested at 115 and 230 A2.3 Dual marking
If the external power supply meets different energy performance for supply voltages, then the external power supply may voluntarily be marked with its performance mark qualified by voltage at which it applies, with the appropriate voltage marked immediately beside the mark. Figure A2 provides an example of dual marking, where the external power supply meets performance Mark IV at 115
and Mark III at 230
FIGURE A2 EXAMPLE OF DUAL MARKING
A2.4 P erformance mark for models capable of multiple input voltages when
tested at 230 only If the external power supply is capable of multiple input voltages, but is tested and complies with the above requirements at 230 only, then the mark shall be
qualified with ‘230’ as per the examples in Figure A3.
FIGURE A3 EXAMPLES FOR 230 COMPLIANCE ONLY
AMDT No. 1 FEB 2009
L i c e n s e d t o M s Y u n L i o n 12 A p r i l 2012. P e r s o n a l u s e l i c e n c e o n l y . S t o r a g e , d i s t r i b u t i o n o r u s e o n n e t w o r k p r o h i b i t e d .
职称英语 报名
A2.5 P erformance mark for models capable of multiple input voltages when
tested at 115 only If the external power supply is capable of multiple input voltages, but is tested and complies with the above requirements at 115 only, then the mark shall be
qualified with ‘115’ as per the examples in Figure A4.
FIGURE A4 EXAMPLES FOR 115 COMPLIANCE ONLY
AMDT No. 1 FEB 2009
L i c e n s e d t o M s Y u n L i o n 12 A p r i l 2012. P e r s o n a l u s e l i c e n c e o n l y . S t o r a g e , d i s t r i b u t i o n o r u s e o n n e t w o r k p r o h i b i t e d .
