全自动抛光机原版说明书(中英文)

更新时间:2023-06-16 16:15:16 阅读: 评论:0

设备说明书EQUIPMENT MANUAL ITC-M-4-700全自动抛光机AUTOMATIC POLISHING MACHINE
内容概要
CATALOGUE
一、设备特点及描述EQUIPMENT FEATURE AND DESCRIPTION
星期二的英语单词二、设备安装EQUIPMENT INSTALLATIONjita
三、设备操作及参数调用EQUIPMENT OPERATION AND PARAMETER USING
bastard四、参数设定与修改PARAMETER WRITE AND CHANGE
nect
五、设备维护及保养EQUIPMENT MAINTENANCE
六、安全操作等其它事项OPERATION SAFTLY AND OTHERS
英语四级考试试题一、设备特点及描述EQUIPMENT FEATURE AND DESCRIPTION
arrow keys
布轮直径WHEEL DIAMETER400–800mm
工位车轴直径STATION AXLE DIAMETER70mm
布轮可变转速WHEEL SPEED100-2400rpm
装机功率INSTALLED POWER40KW
cips电源电压POWER SUPPLY VOLTAGE380V.+N+PE
排尘口直径DUST OUTLET DIAMETER2×200mm
转台轴可变转速TRUNTABLE AXIS VARIABLE SPEED1–25rpm 通过过滤器处理的干净气源CLEAN GAS SOURCE THROUGH THE FILTER >0.6Mpa
工件高度WORKERPIECE HIGHT150mm
前后行程FORWARD AND BACKWARD0-380mm
左右行程LEFTWARD AND RIGHTWARD0-280mm
设备尺寸DIAMENSION OF THE EQUIPMENT4240×2110×2115mm 设备重量WEIGHT OF THE EQUIPMENT5000KG
该设备专为自动抛光而设计,并使用一项新技术对物体进行抛光。特别是在对不规则物体某一部分进行抛光时,可以在不损害整体的情况下整齐平滑地完成任务。采用双组操作程序,同时可以精抛两种不同的工件,设备可以自动切换。同时也采用了角度精抛程序,通过编程,设定精抛角度,对工件复杂的部位可以加强精抛的力度。
布轮的直径大设计灵活,可以在仅旋转数圈的情况下就能达到较高的速度。
物体的固定通过设备夹钳进行控制。该设备是由两边抛光布轮,一个带有4个工位车轴的旋转工作台组成,可以一次性抛光出两件成品。
The device is designed for automatic polishing,and using a new technique for polishing the object,especially in certain parts of irregular objects polishing.Under the condition of without make damage to the whole part,it
can polish smoothly and tidily.Dual group procedures,and can polish two different parts at the same time,the device can automatically switch.It also adopted the point of precision polishing process,by programming,tting fine polishing angle of the work piece of complex parts can strengthen the polish.
The wheel diameter designed to be flexible,you can only spin a few laps in the ca will be able to reach a higher speed.
The device make fixture by clamp.The device have polishing wheel on either side,with a four-station rotary table axle components,you can polish two products at the same time.
二、设备安装EQUIPMENT INSTALLATION
1、客户接收到设备后,要检查其是否由于运输而受损,或者设备缺少部件和相应
的更换布轮的特殊扳手。如发现以上两种情况中的任意一种,应尽早通知相关负责人。
英语4级准考证
After the customer receives the equipment,he or she should check whether there is any damage,missing parts or equipment replacement cloth wheel and the corresponding special wrench during the transport.If any one of them happen,he or she should notify the responsible person.
2、对设备的挪动,可以用起重机(如图1)或叉车。设备必须放置在平地上,混
凝土地面最好,把设备配的四个垫铁安上,调整设备的水平位置。
Moving the equipment can u crane(Figure1)or forklift.Equipment must be placed on level ground,preferably concrete floor.The placement of the device with four horns,adjust the horizontal position of the device.
图1
3、设备供气总进气源必须有经过过滤器处理后的干净气源,通过调压三联件把气
压设定在≥0.6MPa。
The total inlet gas source of equipment must be procesd through the filter clean air source,through the pressure regulator t at FRL≥
0.6MPa.
有声读物mp3打包下载4、装好喷蜡系统即先把喷蜡罐出蜡的螺纹口与设备的进蜡螺纹口衔接紧固,再把
喷蜡罐上面的气源接好,把压力调在0.2-0.3MPa。
beginingInstall the paste supply system is link spray cans of wax in the threads and screw the device into the mouth of convergence fastening wax at first.
Then the gas tank above the source connected,adjust the pressure in the
0.2-0.3MPa.
5、检查电压是否如控制面板上所示:

本文发布于:2023-06-16 16:15:16,感谢您对本站的认可!

本文链接:https://www.wtabcd.cn/fanwen/fan/90/147162.html

版权声明:本站内容均来自互联网,仅供演示用,请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系,我们将在24小时内删除。

标签:设备   抛光   情况   布轮   进行   是否   气源
相关文章
留言与评论(共有 0 条评论)
   
验证码:
Copyright ©2019-2022 Comsenz Inc.Powered by © 专利检索| 网站地图