一、浇口(入水)：gate
浇口进入位置：gate location
浇口形式：gate type
大水口(2板模)：edge gate, side gate
细水口(3板模)：pin-point gate
浇口大小：gate size
转开关流道：switching runner/gate
唧嘴直径：sprue diameter
二、流道：runner
热流道：hot runner，hot manifold
温控箱：temperature controller
热嘴冷流道：hot sprue/cold runner
唧嘴直流：direct sprue gate
圆形流道：round(full/half) runner
模流道电脑分析：mold flow analysis
流道平衡：runner balance
热嘴：hot sprue
热流道板：hot manifold
发热管：cartridge heater
探温针：thermocouples
插头：connector plug
插座：connector socket
密封/封料：al
三、运水：water line
喉塞：line plug
喉管：tube
塑胶管：plastic tube
快速接头：jiffy quick connector plug/socket 四、模具零件：mold components
三板模：3-plate mold
二板模：2-plate mold
导柱(边钉/导边)：leader pin/guide pin
导套(边司)：bushing/guide bushing
顶针板：ejector retainer plate
托板：support plate
螺丝：screw
管销(管钉)：dowel pin
开模槽：ply bar slot
内模管位锁：core/cavity inter-lock
顶针：ejector pin
司筒：ejector sleeve
司筒针：ejector sleeve pin
推板：stripper plate
缩呵：movable core，return core，core puller 扣机(尼龙拉勾)：nylon latch lock
斜顶：lifter
模胚(架)：mold ba
上内模：cavity inrt
下内模：core inrt
行位(滑块)：slide
镶件：inrt
压座(斜鸡)：wedge，heeled block
耐磨板/油板：wedge wear plate
压条：guide way plate
模顶(撑头)：support pillar
唧嘴：sprue bushing
挡板：stop plate
定位圈：locating ring
锁扣：latch
扣鸡：parting lock t
推杆：push bar
栓打螺丝：S.H.S.S.(socket head shoulder screw) 杯头螺丝：S.H.C.S.(socket head cap screw)
活动臂：lever arm
分流锥：sprue parator
雅思6分培训班垃圾钉：stop pin
水隔片：buffle
弹弓柱：spring rod
弹弓：die spring
中托司：ejector guide bush
中托导套(边)：ejector guide pin
镶针：inrt pin
波子弹弓：ball catch
喉塞：pipe plug
锁模块：lock plate
行位斜导柱：angle pin
斜顶杆：angle ejector rod
复位键/提前回杆：early return bar
气阀：valves
五、术语：terms
承压平面平衡：parting surface support balance
模排气：parting line venting
回针碰料位：return pin and cavity interference
desperate
模闭合总厚度：mold ba shut height
顶针碰运水：water line interferes with ejector pin
料位出上(下)模：part from cavity (core) side
模胚原身出料位：cavity direct cut on A-plate，core direct cut on B-plate.
不准用镶件：do not u (core/cavity) inrt
用铍铜做镶件：u beryllium copper inrt
初步(正式)模图设计：preliminary (final) mold design
反呵：rever core
弹弓压缩量：spring compresd length
强度不够：insufficient rigidity
均匀冷却：even cooling
扣前模：sticking
热膨胀：thermo expansion
公差：tolerance
铜电极(铜公)：copper electrode
石墨电极：graphite electrode
夹线：weld line
翘曲：warpage
缺胶：short shot
困气：air trap
界面英文
毛刺：flash，burr
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
模具述语
一、入水：gate
进入位：gate location
水口形式：gate type
大水口：edge gate
细水口：pin-point gate
水口大小：gate size
转水口：switching runner/gate
唧嘴口径：sprue diameter
二、流道: runner
热流道：hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate
圆形流道：round(full/half runner规律英语
流道电脑分析：mold flow analysis
流道平衡:runner balance
热嘴：hot sprue
热流道板：hot manifold
发热管：cartridge heater
牙医的英文
探针: thermocouples
插头：connector plug
插座：connector socket
密封/封料：al
三、运水：water line
cnn china
喉塞：line lpug
限制性从句
喉管：tube
塑胶管：plastic tube
雅思考试报名网快速接头：jiffy quick connector plug/socker 四、模具零件：mold components
三板模：3-plate mold
二板模：2-plate mold
边钉/导边：leader pin/guide pin
边司/导套：bushing/guide bushing
中托司：shoulder guide bushing
中托边L：guide pin
顶针板：ejector retainner plate
托板：support plate
as well螺丝：screw
管钉：dowel pin
开模槽：ply bar scot
内模管位：core/cavity inter-lock
顶针：ejector pin
司筒：ejector sleeve
司筒针：ejector pin
推板：stripper plate
缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock
斜顶：lifter
模胚（架）：mold ba
上内模：cavity inrt
下内模：core inrt
行位（滑块）：slide
optic nerve镶件：inrt
压座/斜鸡：wedge
耐磨板/油板：wedge wear plate
压条：plate
撑头: support pillar
唧嘴：sprue bushing
挡板：stop plate
定位圈：locating ring
锁扣：latch
扣鸡：parting lock t
推杆：push bar
栓打螺丝：S.H.S.B
顶板：eracuretun
活动臂：lever arm
分流锥：spure sperader
水口司:bush
垃圾钉：stop pin
隔片：buffle
弹弓柱：spring rod
弹弓:die spring
中托司：ejector guide bush
中托边：ejector guide pin
镶针：pin
销子：dowel pin
波子弹弓：ball catch
喉塞: pipe plug
锁模块：lock plate
斜顶：angle from pin
