Vikuiti ™Reflective Display Film – Black (RDF-B)Vikuiti ™Reflective Display Film – Clear (RDF-C)Vikuiti ™Transflective Display Film (TDF)
Vikuiti ™Dual Brightness Enhancement Film – Adhesive (DBEF-A)
D e s c r i p t i o n :
This is a family of multilayer optical films utilizing 3M’s unique reflective polarizer technology. This technology provides a film that is a reflective polarizer, in that it transmits light of one polarization, and reflects the light of the other polarization, which normally would have been absorbed by a conventional polarizer. Due to their far greater reflectivity, they provide greatly incread background brightness for higher perceived contrast and readability.They are intended to be direct replacements for the conventional rear polarizer in monochrome display modules.The film is available in four versions:
Vikuiti RDF-B film for purely reflective applications not using a backlight.Vikuiti TDF film for transflective applications which incorporate a backlight.Vikuiti RDF-C film for colored characters or backgrounds.Vikuiti DBEF-A film for mirror-like characters or background.3Innovation
The film’s basic construction is illustrated below.
Protective Liner . . . . . . . .51 microns Adhesive . . . . . . . . . . . . . .
28 microns
Reflective Polarizer . . . . .130 microns
Dark Coating . . . . . . . . . . .13 microns (not on Vikuiti DBEF-A or RDF-C films)Protective Liner . . . . . . . .
51 microns
Delivered Thickness . . . . .273 microns Applied Thickness . . . . . .171 microns (excluding liners)
The illustration below may help you understand the differences between the 4 versions.
瑜珈教练培训
550 mm
creepy330mm
All four films are nearly identical except for the dark coating and type of adhesive. The front side of Vikuiti DBEF-A film is mirror-like, while the other three films are a bright diffu gray color. The backside of Vikuiti RDF-B film is a completely opaque black coating, while the back side of Vikuiti TDF film is a mi-opaque
neutral density dark coating. The back side of Vikuiti RDF-C film and Vikuiti DBEF-A film has no dark coating at all and has a silvery metallic appearance, and is approximately 13 microns thinner than the other two films. All three films have removable protective liners on both sides and a front adhesive layer. Vikuiti DBEF-A film comes only in a 300mm x 350mm sheet, while the other three films are available in 330mm x 550mm mastersheets,and 11 in. x 11 in. notched sample sheets.
Vikuiti ™RDF-B Film
Diffu Adhesive
Reflective Polarizing Film
Totally Opaque Black Coating剑桥英语预备级
™50% Neutral Density Coating
Vikuiti ™RDF-C FIlm
Diffu Adhesive
Reflective Polarizing Film
No Coating Diffu adhesive caus bright diffu look
Vikuiti ™DBEF-A Film
No Coating Clear adhesive caus specular mirror look
Vikuiti ™RDF/TDF Film
Mastersheet
Vikuiti ™DBEF-A Film
Mastersheet
Vikuiti ™RDF/TDF Film Notched Sample Sheet
Top Polarizer Glass LC Layer Glass
Vikuiti ™RDF/TDF/DBEF-A Film
A p p l i c a t i o n s :
The films replace the rear polarizer/reflector or polarizer/transflector of a typical display. It is laminated to the back of the LCD glass module as illustrated below.
The films work differently from conventional absorbing polarizers, and should be aligned 90 degrees away from the angle that a conventional rear polarizer would have been mounted. This would make its transmission axis parallel to the transmission axis of the front polarizer, as illustrated below. Some displays do not have their front and rear polarizers at 90 degrees to each other. But even in this ca, whenever Vikuiti RDF/TDF film replaces a conventional rear polarizer, its transmission axis should be 90 degrees away from the angle the conventional rear
vsp
polarizer would have ud.
Front and Rear Polarizer Alignment
Typical TN Display Vikuiti ™RDF/TDF Film Display
Orthogonal
Parallel
会计硕士考试Front Rear Front Vikuiti ™
hands up
Polarizer Polarizer Polarizer
再别康桥英文版RDF/TDF Film
3三月英文
Electronic Display Lighting Optical Systems Division
3M Center,Building 260-5N-10St. Paul,MN /Vikuiti
Minimum 10% Post-Consumer Fiber
Vikuiti and the Vikuiti “Eye” symbol are trademarks of 3M.Printed in U.S.A. © 3M 2003
75-0500-5205-1
Important Notice to Purchar
The following is made in lieu of all warranties, express or implied, including any implied warranties of merchantability or fitness for a particular purpo.
3M warrants that, at the time of shipment, product will meet 3M’s published specification or that specification agreed in writing between 3M and purchar. Should product not meet specifications at time of shipment, 3M will replace or refund the purcha price of such quantity of the product found not to meet specifications. Purchar shall determine the suitability of the 3M product for purchar’s application. 3M shall not be liable under any legal theory, including in contract or in tort, for any injury, loss, or damage, whether direct, indirect,incidental, special or conquential, arising out of the u of or the inability to u the product.
The warranties and remedies t forth herein are purchar’s sole and exclusive warranties and remedies.
G e n e r a l C o n v e r t i n g , A s s e m b l y, a n d H a n d l i n g R e c o m m e n d a t i o n s
Die cutting is the recommended form of converting and will result in the cleanest edges, although shear cutting and lar cutting may also be acceptable. Whatever method ud, you should ensure that the part has clean,crisp edges without any raggedness or other damage. The are multilayer films and any abu of the edges can cau the layers to delaminate.
During converting operations, both the front and rear protective liners should remain on the film.
If lar cutting, be sure to cut with the adhesive side of the film down, and adjust power levels if necessary to insure that the protective liners remain easily peelable.
Keep the area very clean to lesn the likelihood of debris contaminating adhesive surfaces. Maintaining Class 100 Cleanroom conditions is recommended.
U anti-static measures, such as ionized air blowers, whenever possible to decrea dust attraction to adhesive surfaces.
As always, protect the film, especially the edges, from any undue shock or stress.Wear clean-room gloves if fingerprints are a problem.
Remove liners by tacking near an edge or corner with a piece of aggressive tape and pulling gently.
Avoid forcibly pulling with fingers.
Avoid touching the adhesive surfaces by holding the product at the edges.The LCD glass should be spotlessly clean for proper adhesion.Laminate with a rubber roller to avoid trapping air bubbles.
读mba有用吗Autoclaving is recommended for the removal of lamination defects and to increa the adhesive bond. Autoclave conditions of 50 degrees C at 70 PSI for 30 minutes are suggested.
Annealling is also recommended to improve the adhesive bond. Conditions of 70-80 degrees C for 5 hours are suggested.
动漫动画学校If rework is necessary, the film can be removed with a razor blade. Heating with a hair dryer to soften the adhesive may be uful.
S t o r a g e
Material should be stored in its original packaging laying in a horizontal orientation. Heavy objects should not be piled on top of it to avoid deforming the product. Ambient temperature and humidity should be controlled to 10 – 30 degrees C at 50 – 80% R.H.
