REVISION:
ECR/ECN INFORMATION: SHEET No.
EC No: UAU2010-1892 A
TITLE: STAC64 SYSTEM APPLICATION GUIDE
1 of 15
STAC64 SYSTEM APPLICATION GUIDE
1.0 SCOPE THIS INSTRUCTION MANUAL CONTAINS SUPPLEMENTAL INFORMATION PERTAINING
TO THE MOLEX STAC64 UNSEALED DUAL ROW 0.64 SERIES 34729, STAC64 UNSEALED DUAL ROW HYBRID 2.8-1.5 SERIES 31372, AND THE STAC64 HEADERS SERIES 34690, 34691
Section 1: Product Introduction Section 2: Product Summary Section 3: Connector Asmbly Section 4: Connector Mating Section 5: Service Instructions
Table of Contents
REVISION:
ECR/ECN INFORMATION: SHEET No.
EC No: UAU2010-1892 A
TITLE: STAC64 SYSTEM APPLICATION GUIDE
2 of 15
2.0 PRODUCT DESCRIPTION
34690 Single Bay Vertical Headers 34691 Single Bay Right Angle
toefl ibt
34695 Single Bay Hybrid Vertical Headers
34696 Single Bay Hybrid Right Angle Headers 34707 Ganged Multi-Bay Vertical Headers
34708 Ganged Multi-Bay Right Angle Headers 34729 8-20 Circuit Receptacle Connectors 31372 10 Circuit Hybrid Receptacle Asmbly 34803 CTX64 Female Receptacle Terminals 33012 MX150 Female Receptacle Terminals
REVISION: ECR/ECN INFORMATION: SHEET No.
EC No: UAU2010-1892 A
TITLE: STAC64 SYSTEM APPLICATION GUIDE
3 of 15
3.0 REFERENCE DOCUMENTS SD 34729-020, PK 31301-201, AND PS-34729-020. SD-34690-100, SD-34691-100, SD-34695-100, SD-34696-100, SD-31372-900, PS-31372-100, PK-31372-931, PS-34691-100, PS-34696-100
越俎代庖怎么读
catti二级笔译
REVISION: ECR/ECN INFORMATION: SHEET No.
EC No: UAU2010-1892
A
TITLE:
STAC64 SYSTEM APPLICATION GUIDE
4 of 15
A.Connectors shown in “As Shipped”
Connector TPA shown in “as shipped”condition (pre-lock). The TPA must remain in the
pre-lock position until all circuits are loaded.
B.TPA “lift to pre-lock”
TPA must be in pre-lock position to populate the connector. If during shipping the Connector
TPA moves from it’s pre-lock position. Simply squeeze both sides of the TPA and slide it
up the TPA will snap into pre-lock position.
If the TPA or housing is damaged in any way do not u the connector
Click TPA in Pre-lock
Squeeze & Slide
Squeeze
B.(continued)TPA “lift to pre-lock”HYBRID
stalling
TPA must be in pre-lock position to populate the connector. Slide a small screwdriver英汉在线翻译
Under the edge of the TPA on one side. Using the blade of the screwdriver gently push TPA
upwards. Repeat this on the opposite side, TPA will snap into pre-lock position.
If the TPA or housing is damaged in any way do not u the connector
TPA in Pre-lock
汉尼拔 美剧
六级成绩什么时候公布
tcf
REVISION: ECR/ECN INFORMATION: SHEET No.
EC No: UAU2010-1892 A
TITLE: STAC64 SYSTEM APPLICATION GUIDE
5 of 15
C. Terminal Installation:
With TPA still in pre-lock position, orient terminal to rear of connector as shown below.Grip the wire no less than 1.25 inches from the terminal insulation crimp and inrt
through appropriate circuit opening. If resistance is encountered, retract the terminal and adjust the angle of inrtion. Continue inrting the terminal until it stops and locks up on the lock finger with an audible click.
TPA must be in Pre-Lock Position to Populate Connector
CLICK PUSH PULL民权运动
C.
(continued) Terminal Installation:1.5mm terminals is the same as above
TPA must be in Pre-Lock Position to Populate Connector
CLICK PUSH PULL
C. (continued) Terminal Installation:for 2.8 terminals is the same as above.
asc
2.8mm terminal
CLICK
PUSH PULL
