国外主要工业国家齿轮标准目录
全国标准化技术委员会
2010年7月
一、AGMA 标准
1.AGMA 901-A92 – A Rational Procedure for the Preliminary Design of Minimum
Volume Gears最小体积齿轮初步设计的程序
2.AGMA 908-B89 – Information Sheet - Geometry Factors for Determining the
Pitting Resistance and Bending Strength of Spur, Helical and Herringbone Gear Teeth影响直齿轮、斜齿轮以及人字齿齿轮轮齿抗点蚀及抗弯强度的几何系数
3.AGMA 909-A06 - Specifications for Molded Plastic Gears模制塑料齿轮技术规范
4.AGMA 910-C90 – Formats for Fine-Pitch Gear Specification Data细径节齿轮规
范数据格式
5.AGMA 911-A94 – Design Guidelines for Aerospace Gearing航空航天传动装置设
计指南
6.AGMA 912-A04 - Mechanisms of Gear Tooth Failure齿轮轮齿失效机理
7.AGMA 913-A98 – Method for Specifying the Geometry of Spur and Helical Gears
直齿轮及斜齿轮几何参数确定方法
8.AGMA 914-B04 – Gear Sound Manual - Part I: Fundamentals of Sound as Related
to Gears; Part II: Sources, Specifications and Levels of Gear Sound; Part III: Gear Noi Control齿轮噪声手册-第一部分：齿轮传动噪声的基本原理；
第二部分：齿轮噪声的来源、分类和等级；第三部分：齿轮传动噪声控制
9.AGMA 915-1-A02–Inspection Practices-Part1: Cylindrical Gears- Tangential
Measurements检验规范-第一部分：圆柱齿轮-切向测量
10.AGMA 915-2-A05-Inspection Practices-Part 2: Cylindrical Gears-Radial
Measurements检验规范-第二部分：圆柱齿轮-径向测量美国出国留学的条件
11.AGMA 915-3-A99– Inspection Practices - Gear Blanks, Shaft Center Distance and
Parallelism检验规范-齿轮毛坯、轴中心距及轴线平行度
12.AGMA 917-B97- Design Manual for Parallel Shaft Fine-Pitch Gearing平行轴细径
节齿轮传动设计手册
13.AGMA 918-A93 – A Summary of Numerical Examples Demonstrating the
Procedures for Calculating Geometry Factors for Spur and Helical Gears直齿轮和斜齿轮几何参数计算例概述
14.AGMA 920-A01 – Materials for Plastic Gears塑料齿轮材料
茱15.AGMA 923-B05 – Metallurgical Specifications of Steel Gearing钢齿轮冶金技术
条件
16.AGMA 925-A03 – Effect of Lubrication on Gear Surface Distress齿轮表面润滑影
响
teenager是什么意思17.AGMA 926-C99 – Recommended Practice for Carburized Aerospace Gearing航空
航天渗碳齿轮工艺规范
18.AGMA 927-A01–Load Distribution Factors - Analytical Methods for Cylindrical剩余时间
Gears载荷分配系数-圆柱齿轮分析方法
19.AGMA 929-A06– Calculation of Bevel Gear Top Land and Guidance on Cutteralthough是什么意思
Edge Radius锥齿轮齿顶和刀刃半径的计算
20.AGMA 930-A05– Calculated Bending Load Capacity of Powder Metallurgy (P/M)
External Spur Gears粉末冶金直齿轮承载能力计算
21.AGMA 932-A05– Rating the Pitting Resistance and Bending Strength of Hypoid
Gears准双曲面齿轮抗点蚀与抗弯强度计算
22.AGMA 933-B03 – Basic Gear Geometry基础齿轮几何学
23.AGMA 935-A05– Recommendations Relative to the Evaluation of Radial
Composite Gear Double Flank Testers径向测量齿轮双啮仪的评价全国研究生考试成绩查询
职场英语词汇24.AGMA 938-A05 – Shot Peening of Gears齿轮喷丸处理工艺
25.AGMA 939-A07– Austempered Ductile Iron for Gears奥氏体回火球墨铸铁齿轮
材料
26.AGMA 2015/915-1-A02 – Accuracy Classification System - Tangential英汉词典
Measurement Tolerance Tables for Cylindrical Gears圆柱齿轮精度制-切向测量公差表
27.ANSI/AGMA 1003-G93 – Tooth Proportions for Fine-Pitch Involute Spur and
Helical Gears
28.ANSI/AGMA 1006-A97 – Tooth Proportions for Plastic Gears塑料齿轮齿廓
29.ANSI/AGMA 1010-E95 – Appearance of Gear Teeth - Terminology of Wear and
Failure齿轮轮齿齿面磨损和损伤术语
30.ANSI/AGMA 1012-G05 – Gear Nomenclature, Definitions of Terms with Symbols
齿轮术语、定义
31.ANSI/AGMA 1102-A03 – Tolerance Specification for Gear Hobs齿轮滚刀公差规
范
32.ANSI/AGMA 1106-A97 – Tooth Proportions for Plastic Gears (Metric Edition)塑
料齿轮齿廓（米制）
33.ANSI/AGMA 2001-D04 – Fundamental Rating Factors and Calculation Methods
for Involute Spur and Helical Gear Teeth渐开线直齿轮及斜齿轮轮齿基本参数及计算方法
34.ANSI/AGMA 2002-B88 – Tooth Thickness Specification and Measurement齿厚技
术规范及测量方法
35.ANSI/AGMA 2003-B97 – Rating the Pitting Resistance and Bending Strength of
Generated Straight Bevel, ZEROL Bevel and Spiral Bevel Gear Teeth直齿锥齿轮、零度齿锥齿轮以及弧齿锥齿轮抗点蚀和弯曲强度计算
36.ANSI/AGMA 2004-B89 – Gear Materials and Heat Treatment Manual齿轮材料和
热处理手册
37.ANSI/AGMA 2005-D03 – Design Manual for Bevel Gears锥齿轮设计手册
38.ANSI/AGMA 2007-C00 – Surface Temper Etch Inspection After Grinding [Same as
New ISO 14104]齿轮磨削后表面回火浸蚀检验
39.ANSI/AGMA 2008-C01 – Asmbling Bevel Gears锥齿轮的装配
40.ANSI/AGMA 2009-B01 – Bevel Gear Classification, Tolerances and Measuring
Methods锥齿轮分类、公差以及测量方法
41.ANSI/AGMA 2011-A98 - Cylindrical Wormgearing Tolerance and Inspection
Methods圆柱蜗杆传动装置公差及检验方法
42.ANSI/AGMA 2015-1-A01 – Accuracy Classification System - Tangential
律师函英文
Measurements for Cylindrical Gears圆柱齿轮精度-切向测量
43.ANSI/AGMA 2015-2-A06 - Accuracy Classification System - Radial
Measurements for Cylindrical Gears圆柱齿轮精度-径向测量
44.ANSI/AGMA 2101-D04 – Fundamental Rating Factors and Calculation Methods
for Involute Spur and Helical Gear Teeth (Metric Edition) 渐开线直齿轮及斜齿轮轮齿基本参数及计算方法（米制）
45.ANSI/AGMA 2111-A98 – Cylindrical Wormgearing Tolerance and Inspection
Methods - Metric Edition圆柱蜗杆传动装置公差及检验方法（米制）
46.ANSI/AGMA 2116-A05 - Evaluation of Double Flank Testers for Radial
Composite Measurement of Gears齿轮径向综合测量双啮仪的评价（米制）
47.ANSI/AGMA 6000-B96 – Specification for Measurement of Linear Vibration on
Gear Units齿轮装置线性振动检测规范
48.ANSI/AGMA 6001-D97 – Design and Selection of Components for Enclod Gear
Drives闭式齿轮传动零件的设计和选用
people magazine
49.ANSI/AGMA 6002-B93 – Design Guide for Vehicle Spur and Helical Gears车辆直
齿轮和斜齿轮设计手册
50.ANSI/AGMA/AWEA 6006-A03 – Standard for Design and Specification of
Gearboxes for Wind Turbines风电齿轮箱设计规范和技术条件
51.ANSI/AGMA 6008-A98 – Specifications for Powder Metallurgy Gears粉末冶金齿
轮规范
52.ANSI/AGMA 6011-I03 – Specification for High Speed Helical Gear Units高速斜
齿轮传动装置
53.ANSI/AGMA 6013-A06 - Standard for Industrial Enclod Gear Drives工业闭式
齿轮传动装置
54.ANSI/AGMA 6014-A06 - Gear Power Rating for Cylindrical Shell and Trunnion
Supported Equipment
55.ANSI/AGMA 6022-C93 – Design Manual for Cylindrical Wormgearing圆柱蜗杆
传动装置设计手册
