轮胎专用模具术语(中英文对照)

更新时间:2023-05-08 14:13:39 阅读: 评论:0

Mold Terminology模具术语
AD-Diameter The tread diameter at the centerline of the tread (EU); also: "T-Diameter"(GT)
  AD直径:指胎面中心线直径(EU)。又叫T直径(GT)
Auto-lock Ear A Lug on the cone ring ud to mount the mold/container in the top half of a 60“ NRM Auto-lock press.
  导环上的突缘,用于和60“ NRM Auto-lock 硫化机上半部连接。
Bead Ring The tire bead forming ring (also: toe ring)
  钢圈,也称 toe ring
Bead Ring Register The landing and tapered at that the bead ring fits into
  钢圈配合:侧板上,和 钢圈配合的平面及锥面
Bottom Container Plate The plate that the bottom sidewall plate is bolted to
  模壳底座
Bottom Container Plate Lifting Lug A lug attached to the Bottom Container Plate with Horizontal holes ud for lifting.
 模壳底座吊耳: 装配在底座上、有水平的孔,用来吊装的吊耳
Bottom Container Plate Dowel Pin Lug A lug attached to the Bottom Container Plate that supports the Dowel Pin Bushing.
  装配在底座上,用来支承定位销套的突缘
Bottom Container Plate Hold Down A lug that is ud to fix the Bottom Plate in the Press.
  用来将底座装配在硫化机上的突缘
Breaker Hook A hook fixed to the bottom of the tread gment that catches the bottom container plate only when the gment will not relea from the tire during de-molding.
分离钩:固定在花纹块底部的钩子,轮胎硫化完后若花纹块不能跟轮胎分离,就用此钩抓住模壳底座帮助花纹块和轮胎进行分离。
Breaker Hook Guide Piece
A block bolted to the breaker hook that aligns the tread gment with a slot in the bottom container plate.
  分离钩导块:用螺栓固定在Breaker Hook上,定位花纹块和模壳底座上槽的定位块。
Bronze Wear Plates Any sacrificial metal plate placed under, over or behind a component to keep the components from wearing on each other (greasing)
  青铜耐磨板(油润滑的)
Casting An un-machined cast metal tread ring or Segment
  铸件:未加工的金属花纹圈或花纹块铸件。
Centering Ring The ring mounted on the bottom press platen to locate the mold/ container concentrically to the press; also: "Press register"
  定中环,也称“Press register”
Clamp Rings The bladder clamping asmbly
  胶囊夹盘
Cone Ring The outer ring that transforms the axial movement of the press in a radial one of the gments; also: "Actuator ring", "Squeeze ring" (GT)
  导环,也称"Actuator ring", "Squeeze ring"
Conicity Difference between tread radius over the width
  锥度
Container The mechanical parts that allow a gmented mold to operate; also: mechanism (GT)
  模壳,也叫 mechanism
Container Cavity The space inside of the container that the mold fits into
  模壳内腔:模壳内部放置模具的空间。
DD-Diameter Nominal diameter of a bead ring (EU) Also: "Heel diameter" (GT)
  钢圈的公称直径, 也叫"Heel diameter"
Decoupler Rib A narrow rib that runs circumferentially around the mold and is located near the shoulder area
  在胎肩部位、窄的的圆周向的花筋
DEVA Metal Graphite impregnated bronze metal ud for wear plates in gmented molds (un-gread)
  DEVA类耐磨板:石墨青铜金属,用来制作活络模具的耐磨板(自润滑)。
Dowel Pins The pins that keep the mold halves and parts aligned (containers or HKK molds)
  定位销:用来对模具的半模或零件定位的销(模壳或HKK模具)。
Dowel Pin Bushing A replaceable sleeve ud to register the Dowel Pin locations.
定位销套:对定位销进行定位的可更换的衬套。
DS 2-Diameter The junction diameter between the sidewall plate and the tread gments or tread ring and mould back cavity (EU); also: "S Diameter"(GT)
  口径:侧板与花纹块、花纹圈与mould back 的配合直径. 也叫"S Diameter"
End Gap The distance between cold mold gments (20°C) that allows for heat expansion
 竖缝间隙: 20°C时花纹块竖缝允许热膨胀的间隙
Exterior Mold Identification Plate  A removable plate fastened to the outside of the cone ring listing information pertaining to the mold parts (tread gments, side-plates) asmbled in the container.
  模壳铭牌
Filler rings Full sidewall inrts for molds that fills from the off shoulder area to the I.D.
  嵌入式侧板:从肩部到内径,全部嵌入模具的侧板
Front of mould The reference point at which all dimensional locations are referred
  模具正前方
Heel Diameter See: DD-Diameter
  见 DD-Diameter
Guide Piece A block fixed to the Top Container Plate that registers to a slot in the Cone Ring to keep the Top plate from turning during operation.
  导向块:固定在上盖上,和导环上的槽定位,防止操作过程中上盖转动
Inrt Metal plates pushed or screwed in the side wall plate for exchangeable information活字块(牌)
Insulation Jacket Insulation placed around a container or 2 piece mold (GT) to retain heat
  保温套
Integral type mechanism A mold (tread area) and mechanism that are one unit
  整体式模壳: 花纹部分和模壳是一体的
Ledge Height Bead ledge width on a bead ring
  钢圈上凸出部位的宽度
Lettering The inside lettering of the sidewall; also: "Sidewall engraving" (GT)
  侧板字体图. 也叫"Sidewall engraving"
Maxi Vent (GT) Vent Sleeve A removable inrt for vent holes (Dia.:1,33 mm) to be trimmed.

本文发布于:2023-05-08 14:13:39,感谢您对本站的认可!

本文链接:https://www.wtabcd.cn/fanwen/fan/90/100721.html

版权声明:本站内容均来自互联网,仅供演示用,请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系,我们将在24小时内删除。

标签:花纹   模壳   定位   用来   底座   模具   钢圈   侧板
相关文章
留言与评论(共有 0 条评论)
   
验证码:
Copyright ©2019-2022 Comsenz Inc.Powered by © 专利检索| 网站地图