最全英语专业术语--机械、结构

更新时间:2023-06-03 16:37:44 阅读: 评论:0

模具述语
一、入水:gate
进入位: gate location
水口形式:gate type
大水口:edge gate
细水口: pin-point gate
水口大小:gate size
转水口: switching runner/gate
唧嘴口径: sprue diameter
二、流道: runner
热流道: hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate
圆形流道:round(full/half runner
流道电脑分析:mold flow analysis
流道平衡:runner balance
热嘴: hot sprue
热流道板:hot manifold
发热管:cartridge heater
探针: thermocouples
插头: connector plug
插座: connector socket
密封/封料: al
三、运水:water line
喉塞:line lpug
喉管:tube
塑胶管:plastic tube
快速接头:jiffy quick connector plug/socker
四、模具零件: mold components
三板模:3-plate mold
二板模:2-plate mold
边钉/导边:leader pin/guide pin
边司/导套:bushing/guide bushing
中托司:shoulder guide bushing
中托边L:guide pin
顶针板:ejector retainner plate
托板: support plate
螺丝: screw
管钉:dowel pin
开模槽:ply bar scot
内模管位:core/cavity inter-lock
顶针: ejector pin
司筒:ejector sleeve
司筒针:ejector pin
推板:stripper plate
缩呵:movable core,return core core puller
扣机(尼龙拉勾):nylon latch lock
斜顶:lifter
模胚(架): mold ba
上内模:cavity inrt
下内模:core inrt
行位(滑块): slide
镶件:inrt
压座/斜鸡:wedge
耐磨板/油板:wedge wear plate
压条:plate
撑头: support pillar
唧嘴: sprue bushing
挡板:stop plate
定位圈:locating ring
锁扣:latch
扣鸡:parting lock t
推杆:push bar
栓打螺丝:S.H.S.B
1到10数字谜语
顶板:eracuretun
活动臂:lever arm
分流锥:spure sperader
水口司:bush
垃圾钉:stop pin
隔片:buffle
弹弓柱:spring rod
弹弓:die spring
中托司:ejector guide bush
中托边:ejector guide pin
镶针:pin
销子:dowel pin
波子弹弓:ball catch
模具述语
一、入水:gate
进入位: gate location
水口形式:gate type
大水口:edge gate
细水口: pin-point gate
水口大小:gate size
转水口: switching runner/gate
唧嘴口径: sprue diameter
人生就像一场梦二、流道: runner
热流道: hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate
圆形流道:round(full/half runner
流道电脑分析:mold flow analysis
流道平衡:runner balance
热嘴: hot sprue
热流道板:hot manifold
发热管:cartridge heater
探针: thermocouples
插头: connector plug
插座: connector socket
密封/封料: al
三、运水:water line
喉塞:line lpug
喉管:tube
塑胶管:plastic tube
快速接头:jiffy quick connector plug/socker
四、模具零件: mold components
三板模:3-plate mold
二板模:2-plate mold
边钉/导边:leader pin/guide pin
边司/导套:bushing/guide bushing
中托司:shoulder guide bushing
中托边L:guide pin
顶针板:ejector retainner plate
托板: support plate
螺丝: screw
管钉:dowel pin
开模槽:ply bar scot
内模管位:core/cavity inter-lock
顶针: ejector pin
司筒:ejector sleeve
司筒针:ejector pin
推板:stripper plate
缩呵:movable core,return core core puller
扣机(尼龙拉勾):nylon latch lock
斜顶:lifter
模胚(架): mold ba
上内模:cavity inrt
下内模:core inrt
行位(滑块): slide
镶件:inrt
压座/斜鸡:wedge
耐磨板/油板:wedge wear plate
压条:plate 
撑头: support pillar
唧嘴: sprue bushing
挡板:stop plate
定位圈:locating ring
锁扣:latch
怎样炖燕窝的方法
扣鸡:parting lock t
推杆:push bar
栓打螺丝:S.H.S.B
顶板:eracuretun
活动臂:lever arm
分流锥:spure sperader
水口司:bush
垃圾钉:stop pin
隔片:buffle
弹弓柱:spring rod
弹弓:die spring
中托司:ejector guide bush
中托边:ejector guide pin
镶针:pin
销子:dowel pin
波子弹弓:ball catch
喉塞: pipe plug
锁模块:lock plate
斜顶:angle from pin
斜顶杆:angle ejector rod
尼龙拉勾:parting locks
活动臂:lever arm
复位键、提前回杆:early return bar
气阀:valves
斜导边:angle pin
术语:terms
承压平面平衡:parting surface support balance
模排气:parting line venting 草把做灯
回针碰料位:return pin and cavity interference
模总高超出啤机规格:mold ba shut hight
顶针碰运水:water line interferes withejector pin
料位出上/下模:part from cavith (core) side
模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate.
不准用镶件: Do not u (core/cavity) inrt
用铍铜做镶件: u beryllium copper inrt
初步(正式)模图设计:preliinary (final) mold design
反呵:rever core
弹弓压缩量:spring compresd length
稳定性好:good stability,stable
强度不够:insufficient rigidity
均匀冷却:even cooling
扣模:sticking
热膨胀:thero expansion
公差:tolorance
铜公(电极):copper electrode 
注塑成形不良用语
aberration 色差 atomization 霚化
bank mark 滞料纹 bite 咬入
blacking hole 涂料孔(铸疵) blacking scab 涂料疤
blister 起泡 blooming 起霜
blow hole 破孔 blushing 泛白
body wrinkle 侧壁皱纹 breaking-in 冒口带肉
bubble 膜泡 burn mark 糊斑
burr 毛边 camber 翘曲
cell 气泡 center buckle 表面中部波皱
check 细裂痕 checking 龟裂
chipping 修整表面缺陷 clamp-off 铸件凹痕
collap 塌陷 color mottle 色斑
corrosion 腐蚀 crack 裂痕
crazing 碎裂 crazing 龟裂
deformation 变形 edge 切边碎片
edge crack 裂边 fading 退色
filler speak 填充料斑 fissure 裂纹
flange wrinkle 凸缘起皱 flaw 刮伤
flow mark 流痕 galling 毛边
glazing 光滑 gloss 光泽
grea pits 污斑 grinding defect 磨痕
haircrack 发裂 haze 雾度
incrustation 水锈 indentation 压痕
internal porosity 内部气孔 mismatch 偏模
mottle 斑点 necking 缩颈
nick 割痕 orange peel 橘皮状表面缺陷
overflow 溢流 peeling 剥离
pit 坑 pitting corrosion 点状腐蚀
plate mark 模板印痕 pock 麻点
pock mark 痘斑 resin streak 树脂流纹
resin wear 树脂脱落 riding 凹陷
sagging 松垂 saponification 皂化
scar 疤痕 scrap 废料
scrap jam 废料阻塞 scratch 刮伤/划痕
scuffing 深冲表面划伤 am 裂痕
shock line 模口挤痕 short shot 充填不足
shrinkage pool 凹孔 sink mark 凹痕
skin inclusion 表皮折迭 straightening 矫直
streak 条状痕 surface check 表面裂痕
surface roughening 橘皮状表皮皱折 surging 波动
sweat out 冒汗 torsion 扭曲
warpage 翘曲 waviness 波痕
webbing 熔塌 weld mark 焊痕
whitening 白化 wrinkle 皱纹
冲压英语
stamping, press冲压
punch press, dieing out press冲床 狗的品种大全
uncoiler & strainghtener整平机
feeder送料机
rack, shelf, stack料架
cylinder油缸
robot机械手
taker取料机
conveyer belt输送带
transmission rack输送架
top stop上死点
bottom stop下死点
one stroke一行程
inch寸动
to continue, cont.连动
to grip(material)吸料
location lump, locating piece, block stop 定位块
ret复位
smoothly顺利
dent压痕
scratch刮伤
deformation变形
filings铁削
to draw holes抽孔
inquiry, arch for查寻
to stock, storage, in stock库存
receive领取
approval examine and verify审核
processing, to process加工
delivery, to deliver 交货
to return delivenry to.
to nd delinery back
to retrn of goods退货
registration登记
registration card登记卡
to control管制
to put forward and hand in提报
safe stock安全库存
acceptance = receive验收
to notice通知
application form for purcha请购单
consume, consumption消耗
to fill in填写
abrasion磨损
rever angle = chamfer倒角
character die字模
to collect, to gather收集
failure, trouble故障
statistics统计
demand and supply需求
career card履历卡
to take apart a die卸下模具
to load a die装上模具
to tight a bolt拧紧螺栓
to loor a bolt拧松螺栓
to move away a die plate移走模板
easily damaged parts易损件
standard parts标准件
breaking.(be)broken,(be)cracked 断裂
to lubricate润滑
common vocabulary for die engineering
模具工程常用词汇
die 模具
figure file, chart file图档
hd什么意思
cutting die, blanking die冲裁模
progressive die, follow (-on)die 连续模
compound die复合模
punched hole冲孔
panel board镶块
to cutedges=side cut=side scrap切边
to bending折弯
to pull, to stretch拉伸
Line streching, line pulling线拉伸
engraving, to engrave刻印
upsiding down edges翻边
to stake铆合
designing, to design设计
design modification设计变化
die block模块
folded block折弯块
sliding block滑块
location pin定位销
lifting pin顶料销
die plate, front board模板
padding block垫块
stepping bar垫条
upper die ba上模座
lower die ba下模座
upper supporting blank上承板
upper padding plate blank上垫板
spare dies模具备品
spring 弹簧
bolt螺栓
alloy tool steel 合金工具钢
aluminium alloy 铝合金钢
bearing alloy 轴承合金
blister steel 浸碳钢
bonderized steel sheet 邦德防蚀钢板
carbon tool steel 碳素工具钢
clad sheet 被覆板
clod work die steel 冷锻模用钢
emery 金钢砂
ferrostatic pressure 钢铁水静压力
forging die steel 锻造模用钢
感恩活动galvanized steel sheet 镀锌铁板
hard alloy steel 超硬合金钢
high speed tool steel 高速度工具钢
hot work die steel 热锻模用钢
low alloy tool steel 特殊工具钢
low mangane casting steel 低锰铸钢
marging steel 马式体高强度热处理钢
martrix alloy 马特里斯合金
meehanite cast iron 米汉纳铸钢
meehanite metal 米汉纳铁
merchant iron 市售钢材
molybdenum high speed steel 钼系高速钢 molybdenum steel 钼钢
nickel chromium steel 镍铬钢
prehardened steel 顶硬钢
silicon steel sheet 硅钢板
stainless steel 不锈钢
tin plated steel sheet 镀锡铁板
tough pitch copper 韧铜
troostite 吐粒散铁
tungsten steel 钨钢
vinyl tapped steel sheet 塑料覆面钢板
模具常用刀具与工作法用语
adjustable spanner 活动扳手 angle cutter 角铣刀
anvil 铁钻 arbour 心轴
backing 衬垫 belt sander 带式打磨机
buffing 抛光 chamfering machine 倒角机
chamfering tool 去角刀具 chil 扁錾
chuck 夹具 compass 两角规
concave cutter 凹面铣刀 convex cutter 凸形铣刀
cross joint 十字接头 cutting edge clearance 刃口余隙角
drill stand 钻台 edge file 刃用锉刀
file 锉刀 flange joint 凸缘接头
grinder 砂轮机 hammer 铁锤
hand brace 手摇钻 hatching 剖面线
hexagon headed bolt 六角头螺栓 hexagon nut 六角螺帽
index head 分度头 jack 千斤顶
jig 治具 kit 工具箱
lapping 研磨 metal saw 金工锯
no angle 刀角 pinchers 钳子
pliers 铗钳 plug 柱塞头
怎样给猫咪洗澡polisher 磨光器 protable driller 手提钻孔机
punch 冲头 sand paper 砂纸
scraper 刮刀 screw driver 螺丝起子
scribing 划线 cond out file 中纹锉
spanner 扳手 spline broach 方栓槽拉刀
square 直角尺 square sleeker 方形镘刀
square trowel 直角度 stripping 剥离工具
T-slot T形槽 tool for lathe 车刀
tool point angle 刀刃角 tool post 刀架
tocan 划线盘 trimming 去毛边
waffle die flattening 压纹效平 wiper 脱模钳
wrench 螺旋扳手
机床行业部分英汉对照

本文发布于:2023-06-03 16:37:44,感谢您对本站的认可!

本文链接:https://www.wtabcd.cn/fanwen/fan/89/977076.html

版权声明:本站内容均来自互联网,仅供演示用,请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系,我们将在24小时内删除。

标签:模具   表面   工具钢
相关文章
留言与评论(共有 0 条评论)
   
验证码:
推荐文章
排行榜
Copyright ©2019-2022 Comsenz Inc.Powered by © 专利检索| 网站地图