江门一日游>雅思写作官方题库范文大全木门安装指南(Installment instruction for wood door)
1：门洞的测量方式(Measure size)
1)．门洞的高度：垂直测量门洞上端至地板完成面的距离（若未铺装地板，则必须预留出地面铺装材料的厚度尺寸），选取左右两端两个点进行测量；取其中最小值为门洞的高度尺寸；
Measure height: vertically measure height between bottom and top of wall-hole from the right, the middle, the left, choo the minimum value and deduct thickness of decorative materials of floor.
2)、门洞的宽度：水平测量门洞左右的距离，选取三个以上的点进行测量，取其中最小值为门洞的宽度尺寸。Measure width: horizontally measure width between two side of wall-hole from the top, the middle and the bottom, choo the minimum value as width.
豌豆尖的做法厚度尺寸；如果墙面需要装修，则门洞墙体厚度应附加装饰材料完成面的厚度。
Measure thickness of wall: measure thickness of wall from the top, the middle and the bottom, count the average value and add thickness of decorative materials of wall.
2：安装工具(Tools Required)手抓饭的正宗做法
电锤、木头榔头、平锉、边刨、细齿锯(钢锯)、螺丝刀、角尺、卷尺、吊线锤、电钻、开孔器、戳子、相应规格钻头。
森林防火工作总结>跳大绳比赛作文3：安装材料(Installment material required)
自攻螺丝、木牙螺丝、发泡胶、毛巾、小木条、胶水、门锁、合页、门吸、 墙体隔潮材料，玻璃胶。
Self tapping screw, wood screw, foam adhesive, towel, small wood bar, glue, locks, hinges, door stopper, moist -insulation materials, silicon alant.
4：安装前的准备(installment preparation)
1、门扇、门套运到安装现场后，应把门扇、门套、用垫板或木枋纵向垫平放开放置，若需
靠墙放置
，倾
角不得大于15度。
2、确认安装尺寸、产品型号、清点产品及配件。
3、准备安装工具，详细阅读安装说明书。
Place door leaf and frame at installment site, carefully put and carry door leaf and frame, check whether model is right, count product and accessories, prepare tools and read installment instruction
韦勒克5：安装步骤 (Process of installment)炒土豆的做法
1) 把门套各个部分进行模拟组合，调整门套固定部位的垂直和水平位置，用自攻钉或直钉将其固定。
Asmbly door frame: asmbly door frame by stapler or screw, Inrt rubber al strip,
Inrt rubber al strip
2) 把整体门套置入洞口校正，在门套左右顶端与洞口处用斜型木块嵌入，将其左右竖套板与地面紧密配合。 Fix door frame: put asmbled frame into wall hole, inrt wood wedge into gap between wall and frame to rectify frame.
3)
门套两面要
与
墙体在同一平面上，然后检查门套整体与地面是否垂直，门套顶板与两立板的两个角是否直角，门套立板有无弯曲，检查门套与门是否相符，再打入发泡胶固定。
Examine whether side frame is vertical to the ground and whether top frame is horizontal by level, if inclined, rectify it by wood wedge, after confirmed, fix frame by stapler, finally, inject foam adhesive (Note: don ’t inject excessive adhesive)
Inject foam adhesive
4) 安装合页，螺钉要用螺丝刀拧紧，不能直接用榔头将螺钉打入，门扇上的合页固定好后，门套上的合页要先只拧上一颗螺钉，然后关门检查门的左右和上面的缝隙是否一致，开启是否灵活，确认无误后，再将其它的螺钉拧紧。然后将门扇完整地安装在门框上。
Installment of hinge: Put hinge into pre-slot groove, twist the screw by screwdriver, don’t u hammer to strike screw into door directly, confirm hinge location on the frame side, hung door leaf on frame, at first, only twist one screw for each hinge, and then open and clo door, confirm whether gaps between frame and door leaf is properly(gap from door leaf to ground：8-12mm, gap from door leaf to frame:2-4mm ), make sure that door can be opened and clod smoothly, if it is not properly, adjust it, if it is right, twist remaining four screw
5) 安装门锁与门把手Installment of lock and handle: On the door leaf side, put lock body into pre-slot groove , and then install handles from the side, twist screw to fix it, check whether handle can be rotated smoothly. On the frame side, slot a hole of lock tongue at corresponding position, inrt metal sheet, and then twist screw, finally, check whether door can be opened and clod smoothly!
