• Radio-Controlled.
• Quiet, Safe Electric Flight.
• Includes Vinyl Target.
• Requires:
One 9V Alkaline Battery for Transmitter One CR123A Lithium Battery for Gondola Helium (available at most party
supply stores and florists)
Items may differ from images depicted above
Your kit includes:
1. Metallized inflatable balloon
2. Gondola (thruster module)
3. Transmitter with antenna
4. Putty (for balancing/ballast)
5. Rudder fins
You also need (not included):
切实1. 1 Battery CR123A (3V Lithium battery) for the gondola.
2. 1 Battery 6F22 (9V Alkaline battery) for the transmitter.
3.Helium gas for the balloon (available from florists, party shops, or any other shop lling balloons).
4.Single and double sided-tape to attach gondola and fins to balloon.Install Batteries
Open the gondola’s
battery compartment
by removing the
screw from the
battery compartment's door.
Inrt a
变形虫是真核生物吗
CR123A lithium battery
into the battery holder, ensuring that the polarity is correct. Clo the battery compartment and tighten the screw.Remove the battery cover located at the rear of the transmitter by sliding it
downwards. Inrt a 9V alkaline battery into the battery compartment, again being careful to position it so that the polarity is correct.
Fill Balloon with Helium
Inrt the helium tank nozzle into the Auto-Seal Valve, which is located within the flap on the am of the balloon. Gently push the nozzle into the opening - be careful not to push the nozzle too far as it may damage the balloon’s Auto-Seal Valve. Fill the balloon with Helium until the balloon becomes firm, without over-stressing the ams. Remove the filler nozzle then clo the auto-al valve by pressing the Auto-Seal Valve back together. Note that you can roll the flap up and tape it in position to minimize any chance of Helium leaking out.
Connect the Gondola (Thruster Module)
Apply double-sided tape to the inside bottom of the gondola, around the flat outer area or by which the gondola will be attached to the balloon.Secure the module to the underside of the blimp. You may find it easiest to hold the helium-filled airship with one arm while pressing the taped
module to the bottom center of the balloon with the other hand. Another option is to allow the balloon to ri to the ceiling and then attach the gondola from the underside.
Once the module is attached,apply single-sided tape around
the outside lip to ensure maximum adhesion.
Note that the On/Off switch of the gondola should face the rear of the balloon.
Uncoil the antenna wire and let it trail from the rear of the module -away from the propellers.
NOTE: Placing the module in the position required for proper balance may take a few attempts. You can remove and reposition the module by carefully peeling it away from the balloon. Notice how the balloon reacts with the weight of the gondola. If it is no-heavy then move it slightly backward. If it is tail-heavy then try moving it slightly toward the front of the balloon. Make sure the module is aligned straight along the axis of the balloon!
Install the Styrofoam Fins
Carefully parate the die-cut styrofoam sheet into 4 fins by following the perforated lines. Each fin h
as one edge with tabs that need to be parated. Bend each tab 90° -The first tab to the left and the next to the right, continuing to alternate to the end .
Attach the fins to the rear of the Blimp by using double-sided tape or regular Scotch tape. Ensure that the fins are straight!
Ballast the Balloon
The blimp must be adjusted so that it is neutrally buoyant. This is merely a fancy way of saying that the blimp must float at about eye-level without rising or falling. This is accomplished by adding the correct amount of ‘ballast’ putty. Note that the bombs and battery must already be installed at this point (e next page).
赵丽颖图
Warnings & Safety Precautions!
• This airship is designed for indoor u only!
• The manufacturer is not responsible for any loss or damage caud by unsafe operation of the blimp. Always u common n when piloting your blimp!
• The gondola should be handled carefully. It is made of lightweight
materials that can be easily damaged by rough handling.
• Hold the balloon curely after filling it with Helium to prevent it from flying away!
• Do not continue to fill the balloon after it becomes firm -it could burst.
• The balloon expands when temperature ris. If you completely fill the balloon at a low temperature and the room temperature increas, the balloon may rupture or burst.
Make sure that you are indoors, away from any ventilator, air-conditioner outlet or any other source of air currents.
Allow the weight of the gondola to gently roll the balloon upright, so that the gondola hangs underneath.
avoid是什么意思>最火单机游戏Slowly relea the balloon and note its vertical movement: If the balloon floats upwards place a small piece of putty along the centerline of the gondola. Test the result of the ballast change by again eing if the blimp ris when relead. Continue adding putty until the blimp has no more tendency to ri.
Tip!The putty sticks well to almost any surface once it has been kneaded for a few conds, to soften it. Try to place the putty along the centerline of the gondola (center, front to back). Balance the gondola by placing equal amounts on either side of module. Be sure to keep the putty away from the propellers.
If the balloon sinks remove some of the putty. If the balloon sinks without any putty having been added, carefully add more Helium to the balloon (not too much, as overfilling will cau balloon to burst). Adjust & Repeat until the balloon floats in the air when relead. If the problem persists, try refilling the balloon with fresh Helium.
Note that if you are in a high altitude area, your balloon will not float due to the low air density at your level. In this ca, contact us for a high-altitude balloon. This high altitude balloon is only suitable for high-altitude areas and cannot be ud near a-level due to it’s extreme lift.Important!
The balloon will float for many weeks. However, Helium is a very small atom and will slowly dissipate through the material of the balloon. The balloon will eventually start to look saggy but will probably continue to float. You can u a straw to carefully blow a bit of air into the balloon to plump it up. Eventually, enough Helium will escape through the balloon to cau the balloon to sink. When this happens, add a small amount of helium as described above. Make sure
to adjust the ballast if necessary.
Loading the Bombs
The foam bombs each have a magnetic no which fits into the yellow ‘target’printed within each bomb-bay. There is an electromagnet located within this yellow ‘target’ which holds the bomb until you decide to relea it using the bomb relea button on the transmitter. A vinyl target is included with your Blimp Bomber to make it easy to test your piloting and bombing skills. Challenge your friends, u your imagination to think up games! Let us know what your favorites are!
护理查房制度Operating your blimp
1. Screw the antenna into the top of the transmitter - do not overtighten.
2. Turn on the transmitter via the face-mounted switch. The red LED should light up. If not, check your battery or replace with a fresh one.
3. Move the thruster module's switch to the ‘ON’ position.
4. Follow the instructions that are printed on the face of the transmitter.Esntially, each stick controls one of the side-mounted motors causing it to spin forwards or backwards. The resulting thrust caus the blimp to The two buttons mounted on the top of the controller cau the (single)horizontal prop to spin backwards or forwards. This caus the blimp to ascend or descend. You’ll find that with practice very preci control of your blimp is possible.
Tip!For best performance u short bursts of the engines (1-3 conds).This will conrve battery life as well as make control easier. Experiment with directional control & timing to navigate the vesl as desired.Develop your own skills and techniques!
To drop bombs, press the bomb relea button mounted in the center of the transmitter’s face. Each time you press the button a bomb will be relead.
Gameplay
Compete against friends! Place the target on the floor. Each pilot gets 2minutes to drop his or her bombs onto the target. The one with the best score wins. each pilot takes over from the last one at the spot where the blimp happens to be after two minutes. U your imagination!
Invent competitions such as knocking over targets, steering through cours, time lap racing or even hone your skills trying to pick up light objects by placing a small paper clip on the end of the antenna wire and using it as a hook (You may have to adjust the Ballast Putty to make up for the extra weight). Try delivering the object to a drop-off zone!Safety Precautions for Handling your Blimp
a.Do not u the balloon outdoors since the slightest breeze could blow the balloon away.
b.Do not fly the balloon near sharp or pointed objects. If the balloon repeatedly bumps into sharp or pointed objects, it will damage the balloon and helium gas will leak even though a hole may not be visible.
c.Do not fly the balloon near people, especially children and pets.
d.Do not operate the balloon near people's face or hair. This is very dangerous becau the propellers are constantly turning. If the balloon gets near someone's face or hair, relea the controls to stop the propellers from spinning.
e.The metallized balloon may conduct electricity, which could cau harm or injury. The customer alone is completely fully responsible for the control and safe u of the balloon.
f.Control and navigation will be compromid if operating the balloon near a ventilator, air conditioner outlet or any other source of wind. Avoid rooms with ceiling fans!
g.Do not fly the balloon near any source of heat (Halogen lights,candles, ovens, heat radiators, etc.).
h.When balloon is not in u, leave it inflated inside a cool, dry room with clod windows and doors.
Tip!The module's hanging antenna wire can be ud as a mooring line to tie the balloon to a fixed object.
i.Do not store the balloon in an area where there is a temperature variance of more than 10°. Such an increa in temperature will cau the balloon to expand. If this occurs, carefully open the Auto-Seal Valve carefully inrting a drinking straw and relea a small amount of helium.j.Rooms with windows and direct sunlight may create more than a 10°indoor temperature variance between morning and night. This would NOT be an ideal storage area.
k.The purity of the helium will decrea if air mixes with the Helium. If this occurs, deflate the balloon and refill with fresh Helium.
l.Do not forget to switch OFF the gondola and transmitter when you are finished playing with the blimp.
m.Do not touch the inside of the receiver or the transmitter with your hand or with any metal object.
ballast putty
bomb mount
n.When storing the balloon for a long time period:
1.Remove the module from the balloon by carefully peeling off the tape.
Be careful to hold on to the balloon so it can't float away!
2.Remove the batteries from transmitter and the gondola.
3.Deflate the balloon by carefully inrting a drinking straw into the balloon's valve and then gently squeezing out the balloon's Helium. Warranty in USA and Canada
Your U.S. Navy Blimp is warranted against any manufacturer's defects.
A defective part will be replaced or repaired, with the same or similar model provided that the U.S. Navy Blimp have been operated according to the instructions and that a dated purcha receipt is provided. The warranty does not apply to any product which has been subject to abu, misu, and operation different from that described in this manual, negligence, an accident or not obrving the general safety precautions. Defects caud by tampering, unauthorized alterations or repairs, or other caus not arising out of defects in material or workmanship are not covered by this warranty. Note that the mylar balloon is NOT covered by the warranty.
Warranty in Europe and other countries
The local distributor or retailer will provide a warranty. For further information plea contact the retailer you purchad the product from or contact the importer (name is printed on the package).
Tip! Plea try operating the units with fresh batteries before returning the product. Weak batteries will cau poor performance.
Plea contact Interactive Toy Concepts Ltd. before returning product to your retailer. Most problems can be solved over the phone or via email. Address for shipping products under warranty:
Interactive Toy Concepts Ltd.
1192 Martin Grove Road
Toronto, Ontario, Canada
M9W 5M9
email:***********************
website:
Product must be returned in it’s original packaging, with a proof of purcha and a brief explanation of the problem.
Replacement Parts
If you need to, you can order replacement parts directly from us via telephone or email. Plea call (416) 444-6873 or nd email to ***********************
We rerve the right to make improvements to the design of the Air-Tech Blimp Bomber. Thus, your aircraft may vary slightly from that depicted in the preceding images.
Battery Warnings
U only fresh non-rechargeable batteries of the same or equivalent type as recommended.
Non-rechargeable batteries are
not to be recharged.
寸进尺退Batteries are to be inrted with
the correct polarity.
Exhausted batteries are to be
removed from the toy. Batteries are to be removed if the toy will not be ud for a few days.
The supply terminals (battery contacts) are not to be short-circuited.
FCC Note: (United States Only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cau harmful interference and
(2) This device must accept any interference received, including interference that may cau undesired operation.
NAVY BLIMP Item # 14051AIRSHIP AMERICA 2-channel: Item # 14061 3-channel: Item # 05032 TU
RBO BLIMP
2-channel: Item # 03020 3-channel: Item # 04020
Alien Wizard Item # 02020
BATTLE BOTS Item # 06020BLIMP BOMBER Item # 14001
十字开头的成语
AIRSHIP EARTH Item # 02420STINGRAY Item # 13261 STEALTH Item # 13251
SkyFlyer Item # 13201
