Alarm ID | Signal Name | Description | ||
1 | G1\BTGJ1_1_ALM | BRG METAL TEMP GEN JOURNAL #1 HIGH | 发电机#1轴承金属温度高 | |
2 | G1\BTGJ1_2_ALM | BRG METAL TEMP GEN JOURNAL #1 HIGH | 发电机#1轴承金属温度高 | |
3 | G1\BTGJ2_1_ALM | BRG METAL TEMP GEN JOURNAL #2 HIGH | 发电机#2轴承金属温度高 | |
4 | G1\BTGJ2_2_ALM | BRG METAL TEMP GEN JOURNAL #2 HIGH | 发电机#2轴承金属温度高 | |
5 | G1\BTJ1_1_ALM | BRG METAL TEMP TURB JOURNAL #1 HIGH | 透平#1轴承金属温度高 | |
6 | G1\BTJ1_2_ALM | BRG METAL TEMP TURB JOURNAL #1 HIGH | 透平#1轴承金属温度高 | |
7 | G1\BTJ2_1_ALM | BRG METAL TEMP TURB JOURNAL #2 HIGH | 透平#2轴承金属温度高 | |
8 | G1\BTJ2_2_ALM | BRG METAL TEMP TURB JOURNAL #2 HIGH | 透平#2轴承金属温度高 | |
9 | G1\BTJ3_1_ALM | BRG METAL TEMP TURB JOURNAL #3 HIGH | 透平#3轴承金属温度高 | |
10 | G1\BTJ3_2_ALM | BRG METAL TEMP TURB JOURNAL #3 HIGH | 透平#3轴承金属温度高 | |
11 | G1\BTTA1_2_ALM | BRG METAL TEMP THRUST ACTIVE 2 HIGH | 主推力瓦2金属温度高 | |
12 | G1\BTTA1_5_ALM | BRG METAL TEMP THRUST ACTIVE 5 HIGH | 主推力瓦5金属温度高 | |
13 | G1\BTTA1_8_ALM | BRG METAL TEMP THRUST ACTIVE 8 HIGH | 主推力瓦8金属温度高 | |
14 | G1\BTTI1_2_ALM | BRG METAL TEMP THRUST INACTIVE 2 HIGH | 副推力瓦2金属温度高 | |
15 | G1\BTTI1_5_ALM | BRG METAL TEMP THRUST INACTIVE 5 HIGH | 副推力瓦5金属温度高 | |
16 | G1\BTTI1_9_ALM | BRG METAL TEMP THRUST INACTIVE 9 HIGH | 副推力瓦9金属温度高 | |
17 | G1\L12H_ACC_ALM | PROT MODULE SPEED SGNL LOSS (DECEL DET) | 保护模块转速信号丢失 | |
18 | G1\L12H_ALM | ELECTRICAL OVERSPEED TRIP - HP | 电超速遮断-高速 | |
19 | G1\L12H_FLT_ALM | LOSS OF PROTECTIVE HP SPEED SIGNALS | 高转速保护信号丢失 | |
20 | G1\L12H_P_ALM | PROTECTIVE OVERSPEED STATUS | 超速保护状态 | |
21 | G1\L12HBLT_ALM | PROTECTIVE OVERSPEED BOLT TRIP | 机械超速保护遮断 | |
22 | G1\L12HF_ALM | CONTROL SPEED SIGNAL LOSS - HP | 控制转速信号丢失-高速 | |
23 | G1\L12HFD_C_ALM | CONTROL SPEED SIGNAL TROUBLE | 控制转速信号故障 | |
24 | G1\L12HFD_P_ALM | PROTECTIVE SPEED SIGNAL TROUBLE | 保护转速信号故障 | |
25 | G1\L25A_ENAB_AL | K25A RELAY HAS NOT BEEN ENABLED | K25V继电器未激活 | |
28 | G1\L26BW_ALM | ON LINE WATER WASH TEMPERATURE NOT OK | 在线水洗温度未OK | |
29 | G1\L26CR1H_ALM | STARTING MEANS CRANK MOTOR TEMP HIGH PHASE#1-TRIP | 启动马达A相温度高-遮断 | |
30 | G1\L26CR1HH_ALM | STARTING MEANS CRANK MOTOR TEMP VERY HIGH PHASE#1 | 启动马达A相温度极高 | |
31 | G1\L26CR2H_ALM | STARTING MEANS CRANK MOTOR TEMP HIGH PHASE#2-TRIP | 启动马达B相温度高-遮断 | |
32 | G1\L26CR2HH_ALM | STARTING MEANS CRANK MOTOR TEMP VERY HIGH PHASE#2 | 启动马达B相温度极高 | |
33 | G1\L26CR3H_ALM | STARTING MEANS CRANK MOTOR TEMP HIGH PHASE#3-TRIP | 启动马达C相温度高-遮断 | |
34 | G1\L26CR3HH_ALM | STARTING MEANS CRANK MOTOR TEMP VERY HIGH PHASE#3 | 启动马达C相温度极高 | |
35 | G1\L26CTH_ALM | CONTROL PANEL TEMPERATURE HIGH | 控制盘温度高 | |
53 | G1\L26QA_ALM | LUBE OIL HEADER TEMPERATURE TOO HIGH | 滑油母管温度太高 | |
54 | G1\L26QN_ALM | LUBE OIL TANK TEMPERATURE TOO LOW | 滑油箱温度太低 | |
55 | G1\L26QT_ALM | LUBE OIL HEADER TEMPERATURE HIGH HIGH | 滑油母管温度高高 | |
60 | G1\L27BLN11_ALM | BAT CHAR AC UNDERVOLT - T.D. NORMAL SD | 充电机交流低电压-T.D.正常SD | |
61 | G1\L27BLN12_ALM | BAT CHAR AC UNDERVOLT - INSTANT NORMAL SD | 充电机交流低电压-及时正常SD | |
62 | G1\L27BLN13_ALM | BATTERY CHARGER AC UNDERVOLTAGE - SHUTDOWN | 充电机交流低电压-停机 | |
63 | G1\L27BN_12_ALM | AC BUS NORMAL INFORMATIONS MISMATCH | 交流母线正常信息失谐 | |
64 | G1\L27BN_ALM | BUS UNDERVOLTAGE - NO AUTO SYNCH | 母线低电压-不能自动同期 | |
67 | G1\L27BZ_12_ALM | AC BUS UNDERVOLTAGE INFORMATIONS MISMATCH | 交流母线低电压信号失谐 | |
68 | G1\L27DZ_ALM | DC POWER SUPPLY UNDERVOLTAGE | 直流系统低电压 | |
69 | G1\L27GRDAC_ALM | GAS DETECT RACK 230 VAC POWER SPPLY FLT | 燃气探测器230V交流电源故障 | |
70 | G1\L27GRDDC_ALM | GAS DETECT RACK 125 VDC POWER SPPLY FLT | 燃气探测器125V直流电源故障 | |
72 | G1\L27MC1N_ALM | MCC BUS #1 UNDERVOLTAGE | MCC#1母线低电压 | |
74 | G1\L27N_ALM | NORMAL SUPPLY LOW VOLTAGE | 正常电源电压低 | |
75 | G1\L27QEL_ALM | LUBE OIL EMERGENCY PUMP MOTOR UNDERVOLTAGE | 应急滑油泵马达低电压 | |
76 | G1\L27S_ALM | STAND BY SUPPLY LOW VOLTAGE | 备用电压低 | |
77 | G1\L27TF_ALM | INLET FILTER DEFECT POWER SUPPLY TROUBLE | 入口过滤器电源故障 | |
79 | G1\L28FD_ALM | FLAME DETECTOR TROUBLE | 火焰探测器故障 | |
80 | G1\L28FD_SD | STARTUP CHECK STOP CHAMB FLMED OUT DURING SD ALARM | 停机时火焰丢失 | |
81 | G1\L28FDT_ALM | LOSS OF FLAME TRIP | 火焰丢失遮断 | |
82 | G1\L2SFT_ALM | STARTUP FUEL FLOW EXCESSIVE TRIP | 启动时燃料量过大遮断 | |
83 | G1\L30AC_APU_AL | AIR PROCESSING UNIT FAULT | 空气处理单元故障 | |
84 | G1\L30BT_ALM | HEAT VENT TURB COMPT CHANGE OVER | 透平冷却风扇切换 | |
85 | G1\L30BTA_ALM | BEARING METAL TEMPERATURE HIGH | 轴承金属温度高 | |
86 | G1\L30BTX_ALM | HEAT VENT TURBINE COMPARTMENT VENT. CHANGE OVER | 透平冷却风扇切换 | |
87 | G1\L30BW_ALM | WATER WASH ONLINE WASHING SKID FAULT | 在线水洗模块故障 | |
88 | G1\L30CBC_ALM | COMP BLD VALVES FAILURE TO OPEN | 防喘阀打开故障 | |
89 | G1\L30CC_ALM | FIRE PROTEC PANEL TROUBLE | 火灾保护模块故障 | |
90 | G1\L30CD_ALM | STARTING MEANS COOLDOWN TROUBLE | 盘车模式启动故障 | |
91 | G1\L30COMM_IO_R | VCMI IO STATE EXCHANGE FOR <R> FAILED | <R>至交换机IO接口故障 | |
92 | G1\L30COMM_IO_S | VCMI IO STATE EXCHANGE FOR <S> FAILED | <S>至交换机IO接口故障 | |
93 | G1\L30COMM_IO_T | VCMI IO STATE EXCHANGED FOR <T> FAILED | <T>至交换机IO接口故障 | |
94 | G1\L30DPFLT_ALM | FLOW INLET DEWPOINT TEMPERATURE SENSOR FAULT | 露点进口温度传感器故障 | |
99 | G1\L30FD_ALM | FAILURE TO IGNITE | 点火失败 | |
100 | G1\L30FORCED_AL | SIGNAL FORCING ENABLED | 信号被强制 | |
101 | G1\L30FPG2L_ALM | GAS FUEL INTER-VALVE PRESS. (P2) LOW | 燃气进口阀压力（P2）低 | |
110 | G1\L30LOAH_ALM | BEARING DRAIN TEMPERATURE HIGH | 轴承回油温度高 | |
111 | G1\L30LOAHH_ALM | BEARING DRAIN TEMPERATURE VERY HIGH | 轴承回油温度非常高 | |
112 | G1\L30LTA | HIGH LOAD TUNNEL TEMP - AUTO UNLOADING | 负荷坑道温度高-自动减负荷 | |
113 | G1\L30LTTH_ALM | LUBE OIL HEADER TEMP SENSOR HIGH SPREAD | 滑油母管温度传感器高信号 | |
116 | G1\L30SPA | COMBUSTION TROUBLE | 燃烧故障 | |
117 | G1\L30SPT | HIGH EXHAUST TEMPERATURE SPREAD TRIP | 排气分散度高遮断 | |
118 | G1\L30SPTA | EXHAUST THERMOCOUPLE TROUBLE | 排烟热电偶故障 | |
119 | G1\L30TWW_ALM | WHEELSPACE TEMP HIGH - WW INHIBITED | 轮间温度高-水洗禁止 | |
120 | G1\L30TXA_ALM | EXHAUST TEMPERATURE HIGH | 排烟温度高 | |
123 | G1\L30VL_ALM | HEAT VENT DLN COMPARTMENT VENT. ELECTRICAL FAULT | DLN小间风扇电气故障 | |
124 | G1\L30VLX_ALM | HEAT VENT DLN COMPARTMENT VENT. CHANGE OVER | DLN小间风扇切换 | |
128 | G1\L30WSA1_ALM | WHEELSPACE TEMP DIFFERENTIAL HIGH | 轮间温度差值高 | |
129 | G1\L30WSA2_ALM | WHEELSPACE TEMPERATURE HIGH | 轮间温度高 | |
130 | G1\L32DW_ALM | GENERATOR BREAKER TRIP REVERSE POWER | 发电机开关遮断逆功率动作 | |
131 | G1\L33ARS_ALM | AC TRANSFER CB SPRING CHARGE FAILURE | 交流信号转换弹性模量信号故障 | |
133 | G1\L33CDMN_ALM | AT MIN TNR REVERSE POWER NOT DETECTED | 逆功率在最小TNR未探测到 | |
140 | G1\L33PS1C_ALM | GAS FUEL VENT VALVE LIMIT SWITCH NOT CLOSED | 气体燃料清吹阀限位开关未关闭 | |
141 | G1\L33PS2O_ALM | GAS FUEL VENT VALVE LIMIT SWITCH NOT OPEN | 气体燃料清吹阀限位开关未打开 | |
142 | G1\L33PSC_ALM | GAS FUEL VENT VALVE CLOSED TROUBLE | 气体燃料清吹阀关闭故障 | |
143 | G1\L33PSO_ALM | GAS FUEL VENT VALVE OPEN TROUBLE | 气体燃料清吹阀打开故障 | |
144 | G1\L33S_ALM | GAS FUEL AUTOMATIC VALVE FAULT | 气体燃料自动阀故障 | |
145 | G1\L33VG11_ALM | GAS FUEL VENT VALVE OUT OF POSITION | 气体燃料排污阀位置故障 | |
147 | G1\L33VL_ALM | HEAT VENT GAS/DLN COMPT VENT FLAP TROUBLE | DLN通风扇故障 | |
148 | G1\L39VA_ALM | HIGH VIBRATION | 振动高 | |
149 | G1\L39VCA_ALM | VIBRATION BN GT. AXIAL SHAFT DISPLACEMENT ALERT | 发电机轴振高报警 | |
150 | G1\L39VCD_ALM | VIBRATION BN GT. AXIAL SHAFT DISPLACEMENT DANGER | 发电机轴振高危险 | |
151 | G1\L39VD1_ALM | VIBRATION SENSOR DISABLED | 振动探测器失效 | |
152 | G1\L39VD3_ALM | VIBRATION START INHIBIT | 振动故障启动禁止 | |
153 | G1\L39VDIFF_ALM | VIBRATION SENSOR DIFFERENTIAL TROUBLE | 振动探测器差别故障 | |
154 | G1\L39VF_ALM | VIBRATION TRANSDUCER FAULT | 振动传感器故障 | |
155 | G1\L39VS10A_ALM | VIB BN GEN BRG #2 RADIAL SHAFT DISPLACEMENT ALERT | 发电机#2轴承振动差别故障 | |
156 | G1\L39VS10D_ALM | VIB BN GEN BRG #2 RADIAL SHAFT DISPLACEMENT DANGER | 发电机#2轴承振动差别危险 | |
157 | G1\L39VS1A_ALM | VIB BN GT BRG #1 RADIAL SHAFT DISPLACEMENT ALERT | 轮机间#1轴承振动差别故障 | |
158 | G1\L39VS1D_ALM | VIB BN GT BRG #1 RADIAL SHAFT DISPLACEMENT DANGER | 轮机间#1轴承振动差别危险 | |
159 | G1\L39VS3A_ALM | VIB BN GT BRG #3 RADIAL SHAFT DISPLACEMENT ALERT | 轮机间#3轴承振动差别故障 | |
160 | G1\L39VS3D_ALM | VIB BN GT BRG #3 RADIAL SHAFT DISPLACEMENT DANGER | 轮机间#3轴承振动差别危险 | |
161 | G1\L39VS9A_ALM | VIB BN GEN BRG #1 RADIAL SHAFT DISPLACEMENT ALERT | 发电机#1轴承振动差别故障 | |
162 | G1\L39VS9D_ALM | VIB BN GEN BRG #1 RADIAL SHAFT DISPLACEMENT DANGER | 发电机#1轴承振动差别危险 | |
163 | G1\L39VSD_ALM | HIGH VIBRATION SHUTDOWN | 振动高停机 | |
164 | G1\L39VT_ALM | HIGH VIBRATION TRIP | 振动高遮断 | |
165 | G1\L3A_ALM | TURBINE UNDERSPEED | 透平低转速 | |
166 | G1\L3APFLT_ALM | AMBIENT PRESS FAULT-XFER TO SITE CONST | 大气压力传感器故障选择常数 | |
167 | G1\L3CPRI_ALM | INLET PRESS DROP MEASUREMENT FAULT | 进气压差测量故障 | |
168 | G1\L3D_UCVX_AF | UCVx AIRFLOW OR OVERTEMPERATURE TROUBLE | 入口空气超温故障 | |
169 | G1\L3D_UCVX_OT | UCVx OVERTEMPERATURE | 入口空气超温 | |
170 | G1\L3DWBCOKZ_AL | FSR LIMITED DUE TO DWATT XDUCER FAILURE | 有功变送器故障限制FSR | |
171 | G1\L3FS1C_T_ALM | GAS FUEL SHUT OFF VALVE SWITCH FAIL TO CLOSED | 燃气截止阀关闭位置故障 | |
172 | G1\L3FTGL_ALM | GAS FUEL TEMPERATURE GAS LOW | 燃气温度低 | |
173 | G1\L3FTGLT_ALM | GAS FUEL TEMPERATURE GAS TOO LOW - TRIP | 燃气温度太低-遮断 | |
174 | G1\L3FTGLZ_ALM | GAS FUEL TEMPERATURE GAS LOW DURING STARTUP - TRIP | 启动期间燃气温度低-遮断 | |
175 | G1\L3GCVA_ALM | G1 GCV NOT FOLLOWING REF | 燃气控制阀（GCV）未跟踪 | |
176 | G1\L3GCVFLT_ALM | GCV SERVO TROUBLE | 燃气控制阀GCV1伺服故障 | |
177 | G1\L3GLTSDTC_AL | SHUT DOWN GAS LEAK TEST COMPLETE | 停机过程可燃气体泄露实验 | |
178 | G1\L3GLTSUTC_AL | START UP GAS LEAK TEST COMPLETE | 启动过程可燃气体泄露实验 | |
179 | G1\L3GRVA_ALM | STOP/SPEED RATIO VALVE NOT TRACKING | 速断阀未跟踪 | |
180 | G1\L3GRVFLT | GAS RATIO VALVE POSITION SERVO TROUBLE | 燃气速比阀位置伺服故障 | |
181 | G1\L3GRVT_ALM | STOP/SPEED RATIO VALVE NOT TRACKING TRIP | 速断阀未跟踪遮断 | |
182 | G1\L3HQ1_ALM | HYDRAULIC SUPPLY MAIN PUMP DEFAULT | 主液压油泵运行报警 | |
183 | G1\L3IGVFLT_ALM | IGV POSITION SERVO FAULT | IGV位置伺服故障 | |
184 | G1\L3LTOT_ALM | LUBE OIL TANK TEMP SENSOR HIGH SPREAD | 滑油箱温度传感器分散度高 | |
185 | G1\L3MP_ALM | MASTER PROTECTIVE START CHECK ETR FAULT | 主保护启动检查ETR故障 | |
186 | G1\L3SFLT_ALM | CONTROL SYSTEM FAULT TRIP | 控制系统故障遮断 | |
187 | G1\L3TFLT_ALM | LOSS OF COMPR DISCHARGE PRESS BIAS | 失去压气机出口压力基准 | |
188 | G1\L3TMFLT1_ALM | STARTING MEANS LOSS TRQ CNV GUIDE VANE FEEDBACK | 启动状态丢失液力变扭器反馈信号 | |
189 | G1\L3TNRERRX | DWATT TOO LOW TO SUPPORT TNR-TNR LOWER | 有功太低降速 | |
190 | G1\L3TTWS_ALM | FORCED COOLDOWN DUE TO CO2 RELEASE | CO2释放致使机组盘车 | |
191 | G1\L3VLST_ALM | HEAT VENT GAS PRESS ULTRA LOW DOWNSTREAM SSOV | 燃气压力极低停止88VL | |
192 | G1\L3VTCC_ALM | EXHAUST TC VTCC COMMUNICATIONS FAULT | 排气温度VTCC诊断报警 | |
193 | G1\L3WCTIM_ALM | WATER WASH ONLINE ONLINE WATER INHIBITED | 在线水洗被禁止 | |
194 | G1\L3Z_ALM | FAILURE TO SYNCHRONIZE | 同期故障 | |
195 | G1\L43ADJ_ALM | VSVO IN CALIBRATION MODE | VSVO校验模式 | |
196 | G1\L43MAINT_ALM | MAINTENANCE - FORCING MODE ENABLED | 维护-强制模式被激活 | |
197 | G1\L45FP1_ALM | FIRE PROTECTION - FIRE PRE ALARM ZONE 1 | 火灾保护-1区域火灾预报警 | |
198 | G1\L45FP2_ALM | FIRE PROTECTION - FIRE PRE ALARM ZONE 2 | 火灾保护-2区域火灾预报警 | |
199 | G1\L45FPX_ALM | FIRE PROTECTION - GENERAL FIRE ALARM ZONE 1 & 2 | 火灾保护-发电机1&2区域火灾报警 | |
200 | G1\L45FTX1_ALM | FIRE PROTECTION - FIRE ALARM ZONE 1 | 火灾保护-1区域火灾报警 | |
201 | G1\L45FTX2_ALM | FIRE PROTECTION - FIRE ALARM ZONE 2 | 火灾保护-2区域火灾报警 | |
202 | G1\L45HA4_ALM | SENSOR 45HA-4 CONTROL CARD FAULT | 传感器45HA-1控制卡故障 | |
203 | G1\L45HA4H_ALM | HZD GAS DETEC DLN COMP-DLN VENT/GAS CAB HIGH LEVEL | 危险气体检测DLN室#4探头高报警 | |
204 | G1\L45HA4HH_ALM | HZD GAS DETEC DLN/AUX COMPT#4 HIGH HIGH LEVEL | 危险气体检测DLN室#4探头高高报警 | |
205 | G1\L45HA4T_ALM | HZD GAS DETEC DLN COMPT- VENT DUCT/GAS CAB TRIP | 危险气体检测DLN室危险气体高遮断 | |
206 | G1\L45HA5_ALM | SENSOR 45HA-5 CONTROL CARD FAULT | 传感器45HA-5控制卡故障 | |
207 | G1\L45HA5HH_ALM | HZD GAS DETEC DLN/AUX COMPT#5 HIGH HIGH LEVEL | 危险气体检测DLN室#5探头高高报警 | |
208 | G1\L45HA6_ALM | SENSOR 45HA-6 CONTROL CARD FAULT | 传感器45HA-6控制卡故障 | |
209 | G1\L45HA6HH_ALM | HZD GAS DETEC DLN/AUX COMPT#6 HIGH HIGH LEVEL | 危险气体检测DLN室#6探头高高报警 | |
210 | G1\L45HGDHH_ALM | HZD GAS DETEC HIGH HIGH LEVEL INFORMATION | 危险气体检测高高值 | |
211 | G1\L45HGDSD_ALM | HAZARDOUS GAS DETECTION FAILURE - SHUT DOWN | 危险气体检测故障-停机 | |
212 | G1\L45HT1_ALM | SENSOR 45HT-1 CONTROL CARD FAULT | 传感器45HA-1控制卡故障 | |
213 | G1\L45HT1H_ALM | HZD GAS DETEC TURBINE COMPT- TURB FRAME HIGH LEVEL | 危险气体检测透平间危险气体高值 | |
214 | G1\L45HT1HH_ALM | HZD GAS DETEC TURBINE COMPT#1 HIGH HIGH LEVEL | 危险气体检测透平间#1探头高高值 | |
215 | G1\L45HT1T_ALM | HZD GAS DETEC TURB COMP - TURB FRAME TRIP | 透平间危险气体检测遮断 | |
216 | G1\L45HT2_ALM | SENSOR 45HT-2 CONTROL CARD FAULT | 传感器45HA-2控制卡故障 | |
217 | G1\L45HT2HH_ALM | HZD GAS DETEC TURBINE COMPT#2 HIGH HIGH LEVEL | 危险气体检测透平间#2探头高高值 easy的最高级 | |
218 | G1\L45HT3_ALM | SENSOR 45HT-3 CONTROL CARD FAULT | 传感器45HA-3控制卡故障 | |
219 | G1\L45HT3HH_ALM | HZD GAS DETEC TURBINE COMPT#3 HIGH HIGH LEVEL | 危险气体检测透平间#3探头高高值 | |
220 | G1\L45HT4_ALM | SENSOR 45HT-4 CONTROL CARD FAULT | 传感器45HA-4控制卡故障 | |
221 | G1\L45HT4H_ALM | HZD GAS DETEC TURBINE COMPT- VENT DUCT HIGH LEVEL | 危险气体检测透平间#4、#5、#6探头高报警 | |
222 | G1\L45HT4HH_ALM | HZD GAS DETEC TURBINE COMPT#4 HIGH HIGH LEVEL | 危险气体检测透平间#4探头高高值 | |
223 | G1\L45HT4T_ALM | HZD GAS DETEC TURB COMP- VENT DUCT TRIP | 危险气体检测透平间危险气体高遮断 | |
224 | G1\L45HT5_ALM | SENSOR 45HT-5 CONTROL CARD FAULT | 传感器45HA-5控制卡故障 | |
225 | G1\L45HT5HH_ALM | HZD GAS DETEC TURBINE COMPT#5 HIGH HIGH LEVEL | 危险气体检测透平间#5探头高高值 | |
226 | G1\L45HT6_ALM | SENSOR 45HT-6 CONTROL CARD FAULT | 传感器45HA-6控制卡故障 | |
227 | G1\L45HT6HH_ALM | HZD GAS DETEC TURBINE COMPT#6 HIGH HIGH LEVEL | 危险气体检测透平间#6探头高高值 | |
228 | G1\L48_ALM | TURBINE INCOMPLETE SEQUENCE | 透平程序未完成 | |
229 | G1\L48CR_ALM | STARTING MEANS TURB SHFT FAIL TO BREAK TURB AWAY | 启动状态盘不动大轴 | |
230 | G1\L49X_ALM | HEAT VENT AUXILIARY MOTOR OVERLOAD | 辅机间风扇马达过载 | |
231 | G1\L4CT_ALM | CUSTOMER TRIP | 紧急遮断 | |
233 | G1\L4IGVT_ALM | INLET GUIDE VANE CONTROL FAULT TRIP | IGV控制故障遮断 | |
234 | G1\L4QESTP1_ALM | DC 88QE PUMP FIRST STEP TIMER FAILURE | 88QE第一时间继电器故障 | |
235 | G1\L4QESTP2_ALM | DC 88QE PUMP SECOND STEP TIMER FAILURE | 88QE第二时间继电器故障 | |
236 | G1\L4QETRPZ_ALM | AC PUMP FAILURE TRIP | 交流油泵故障遮断 | |
237 | G1\L4QETST_ALM | DC PUMP TEST FAILED | 直流油泵试验故障 | |
238 | G1\L4TK_WW_ALM | EXHAUST FRAME BLOWER FAULT. WATER WASH INHIBITED | 排气框架风扇故障-禁止水洗 | |
241 | G1\L51QE_ALM | LUBE OIL EMERGENCY PUMP MOTOR OVERLOAD | 应急油泵马达过载 | |
242 | G1\L51QEFLT_ALM | DC PUMP ABNORMAL POWER | 直流油泵电源异常 | |
243 | G1\L51QEOFF_ALM | EMERGENCY LUBE OIL PUMP OUT OF SERVICE | 应急滑油泵退出工作 | |
248 | G1\L52BT_ALM | HEAT VENT TURBINE COMPARTMENT VENT. FAULT | 透平冷却风扇故障 | |
251 | G1\L52G1_ALM | GENERATOR BREAKER TRIPPED | 发电机开关跳闸 | |
252 | G1\L52HQ1_ALM | HYDRAULIC SUPPLY AUXILIARY PUMP DISCREPANCY | 辅助液压油泵故障 | |
253 | G1\L52QA_ALM | LUBE OIL AUX PUMP IN OPERATION | 辅助滑油泵运行 | |
255 | G1\L52TG_ALM | TURNING GEAR MOTOR FAULT | 盘车马达故障 | |
256 | G1\L52TK1_ALM | EXHAUST FRAME BLOWER #1 DISCREPENCY | 排气框架1#冷却风机故障 | |
257 | G1\L52TK2_ALM | EXHAUST FRAME BLOWER #2 DISCREPENCY | 排气框架2#冷却风机故障 | |
259 | G1\L52VL_ALM | HEAT VENT DLN COMPARTMENT VENT. FAULT | 气体小间排气风机故障 | |
261 | G1\L5CFG_TRP_AL | VPRO - OS SETPOINT CONFIG ERROR TRIP | VPRO超速配置选择错误跳闸 | |
262 | G1\L5E_ALM | EMERGENCY MANUAL TRIP - MKVI PANEL | 手动紧急遮断-MKVI控制面板 | |
263 | G1\L5ESTOP1_ALM | E-STOP 1 PROTECTIVE CIRCUIT LATCHED | #1紧急停机按钮保护线路闭锁 | |
264 | G1\L5ESTOP1_FZA | VPRO E-STOP PB CIRCUIT OPEN | VPRO-紧急停机线路回路闭锁 | |
265 | G1\L5VPRO_LATCH | PROTECTIVE VPRO CARD TRIP - LATCH | 保护VPRO卡遮断-闭锁 | |
266 | G1\L60BOG_ALM | TURBINE STARTUP BOGGED DOWN - TRIP | 透平启动失败-遮断 | |
267 | G1\L60FSRG_ALM | FSR GAG NOT AT MAX LIMIT | FSR不在最大限 | |
268 | G1\L60TRF_ALM | FSR TEMPERATURE REFERENCE ACTIVE | FSR温度基准被激活 | |
269 | G1\L62CD_ALM | COOLDOWN SEQUENCE RUNNING | 盘车程序运行 | |
270 | G1\L62TT2_ALM | STARTUP CHECK STOP FAILURE TO START | 启动检查终止故障禁止启动 | |
271 | G1\L62WWY_ALM | WARNING : VENTIL AFTER OFF LINE WW INTERRUPTED | 警告：通风后离线水洗禁止 | |
273 | G1\L63BWL_ALM | WATER WASH PRESSURE OR FLOW FAULT | 水洗压力或流量故障 | |
274 | G1\L63CA1L_ALM | FLOW INLET GT AIR FILTER COMPRESSED AIR TROUBLE | 进气虑压缩空气故障 | |
276 | G1\L63CPDL_ALM | CPD PRESSURE LOW ALARM | 压气机出口压力低故障 | |
277 | G1\L63CSH_ALM | FLOW INLET COMPRESSOR PRESSURE HIGH ALARM | 压气机进口压力高报警 | |
278 | G1\L63CSH_SENSR | FLOW INLET COMP DIFF PRESS SWITCH TROUBLE | 压气机进口压差开关故障 | |
279 | G1\L63CSHH_ALM | INLET FILTER VERY HIGH PRESSURE DROP - TRIP | 进气滤压差非常高-遮断 | |
280 | G1\L63EAH_ALM | EXHAUST DUCT PRESSURE HIGH | 排气压力高 | |
281 | G1\L63ETF_SENSR | EXHAUST DUCT PRESS SWITCH FAILURE | 排气压力开关故障 | |
282 | G1\L63ETH_ALM | EXHAUST DUCT PRESSURE HIGH TRIP | 排气压力高-遮断 | |
283 | G1\L63FG1_ALM | HEAT VENT 63FG-1 SENSOR TROUBLE | 63FG-1传感器故障 | |
284 | G1\L63FG2_ALM | HEAT VENT 63FG-2 SENSOR TROUBLE | 63FG-2传感器故障 | |
285 | G1\L63FGDH_ALM | GAS FUEL STRAINER DIFF PRESS HIGH | 燃气滤压差高 | |
286 | G1\L63FGL_ALM | GAS FUEL PRESSURE LOW | 燃气压力低 | |
288 | G1\L63GSD1H_ALM | GAS FUEL SCRUBBER GAS #1 DIFF PRESS HIGH | 燃气#1过滤器压差高 | |
289 | G1\L63GSD2H_ALM | GAS FUEL SCRUBBER GAS #2 DIFF PRESS HIGH | 燃气#2过滤器压差高 | |
290 | G1\L63HF1H_ALM | HYDRAULIC SUPPLY FILTER HIGH DIFF PRESSURE | 液压油滤压差高 | |
291 | G1\L63HQ1L_ALM | HYDRAULIC SUPPLY SYSTEM OUTPUT PRESSURE LOW | 液压油系统排出压力低 | |
292 | G1\L63QA2L_ALM | LUBE OIL HEADER LOW PRESSURE | 滑油母管压力低 | |
294 | G1\L63QQ10H_ALM | LUBE OIL MIST ELIM FILTER HIGH DIFF PRESSURE | 油雾分离机滤网压差高 | |
295 | G1\L63QQ1H_ALM | LUBE OIL FILTER HIGH DIFF PRESSURE | 滑油过滤器压差高 | |
296 | G1\L63QQ8H_ALM | LUBE OIL TORQUE CONVERT FILTER HIGH DIFF PRESSURE | 液力变扭器滤网压差高 | |
297 | G1\L63QT_ALM | LUBE OIL GEN PRESSURE LOW LOW | 发电机滑油压力低低 | |
298 | G1\L63QT_SENSR | LUBE OIL HEADER PRESSURE SENSOR FAULT | 滑油母管压力传感器故障 | |
299 | G1\L63QTX_ALM | TURBINE LUBE OIL HEADER PRESS LOW TRIP | 透平滑油母管压力低遮断 | |
300 | G1\L63TF1H_ALM | FLOW INLET FILTER DIFF PRESSURE | 进气虑压差高 | |
301 | G1\L63TK_ALM | COOL SEAL AIR EXH BLOWER FAN#1 OR #2 LOW DIFF PRES | 排气框架冷却风扇#1OR#2压差低 | |
302 | G1\L63TKY_ALM | EXHAUST FRAME PRESS SW TROUBLE | 排气框架压力开关故障 | |
304 | G1\L64D_ALM | BATTERY 125VDC GROUND | 蓄电池125V直流接地 | |
305 | G1\L71GS12A_ALM | GAS FUEL SCRUBBER #1 - 2A LEVEL HIGH | 燃气气水分离器#1-2A液位高 | |
306 | G1\L71GS12B_ALM | GAS FUEL SCRUBBER #1 - 2B LEVEL HIGH | 燃气气水分离器#1-2B液位高 | |
307 | G1\L71GS13_ALM | GAS FUEL SCRUBBER #1 - 3 LEVEL HIGH | 燃气气水分离器#1-3液位高 | |
308 | G1\L71GS1H_ALM | GAS FUEL COALESC FILTER #1 LEVEL HIGH | 燃气#1过滤器液位高 | |
309 | G1\L71GS1HT_SNS | GAS FUEL #1 COALESC FILTER LEVEL SENSOR TROUBLE | 燃气#1过滤器液位传感器故障 | |
310 | G1\L71GS22A_ALM | GAS FUEL SCRUBBER #2 - 2A LEVEL HIGH | 燃气气水分离器#2-2A液位高 | |
311 | G1\L71GS22B_ALM | GAS FUEL SCRUBBER #2 - 2B LEVEL HIGH | 燃气气水分离器#2-2B液位高 | |
312 | G1\L71GS23_ALM | GAS FUEL SCRUBBER #2 - 3 LEVEL HIGH | 燃气气水分离器#2-3A液位高 | |
313 | G1\L71GS2H_ALM | GAS FUEL COALESC FILTER #2 LEVEL HIGH | 燃气#2过滤器液位高 | |
314 | G1\L71GS2HT_SNS | GAS FUEL #2 COALESC FILTER LEVEL SENSOR TROUBLE | 燃气#2过滤器液位传感器故障 | |
315 | G1\L71GSHHT | GAS FUEL SEPARATOR CONDENSATE VERY HIGH LEVEL TRIP | 燃气分离器冷凝装置液位非常高遮断 | |
316 | G1\L71GSHHT_ALM | GAS FUEL SEPARATOR CONDENSATE VERY HIGH LEVEL | 燃气分离器冷凝装置液位非常高 | |
317 | G1\L71QH_ALM | LUBE OIL TANK HIGH LEVEL | 滑油箱液位高 | |
318 | G1\L71QL_ALM | LUBE OIL TANK LOW LEVEL | 滑油箱液位低 | |
319 | G1\L71WG1_ALM | GENERATOR LIQUID LEVEL DETECTOR | #1发电机漏液检测有液体 | |
| 小学生成语故事 | 323 | G1\L72QE_ALM | LUBE OIL EMERGENCY PUMP NOT IN OPERATION | 应急油泵未运行 |
324 | G1\L72QETST_ALM | DC PUMP DID NOT START | 直流油泵未启动 | |
325 | G1\L72QEZ_ALM | LUBE OIL EMERGENCY PUMP IN OPERATION | 应急油泵运行状态 | |
328 | G1\L83CBLIMIT | CBV FAILED TO CLOSE-LOAD LIMITING | CBV关闭故障-负荷受限 | |
329 | G1\L83HOST_ALM | OVERSPEED TEST MODE SELECTED | 超速试验模式选择 | |
330 | G1\L83RBO_ALM | REMOTE BREAKER OPEN DETECTED | 远方开关监视打开 | |
331 | G1\L83WW_ALM | WATER WASH WASHING ONLINE PROHIB INLET TEMP LOW | 进水温度低在线水洗被禁止 | |
332 | G1\L83WWON_ALM | WATER WASH WASHING ONLINE - 24H TIMER PROGR. | 在线水洗-24小时延时 | |
333 | G1\L86ARS_ALM | AC TRANSFER FAULT | 交流转换故障 | |
335 | G1\L86CBA_ALM | COOL SEAL AIR COMP BLEED VALVE CLOSE POS PBL | 冷却密封空气阀关闭 | |
336 | G1\L86CBT_ALM | COOL SEAL AIR COMP BLEED VALVE OPEN POS PBL-TRIP | 冷却密封空气阀打开-遮断 | |
338 | G1\L86CRTX_ALM | STARTING MOTOR PROTECTIVE LOCKOUT | 启动马达保护闭锁 | |
339 | G1\L86FPG2HT_A | POST-IGNITION P2 HIGH TRIP | 后着火P2压力高遮断 | |
340 | G1\L86FPG2IH_AL | PRE-IGNITION P2 PRESS HIGH IGN INHIBIT | 先着火P2压力高被抑制 | |
341 | G1\L86FPG2LT_A | POST-IGNITION P2 LOW TRIP | 后着火P2压力低遮断 | |
342 | G1\L86GCVT_ALM | G1 GCV NOT FOLLOWING REF TRIP | 燃气控制阀GCV未跟踪遮断 | |
343 | G1\L86GLTA_ALM | GAS LEAK TEST OF SRV FAILED | 燃气泄漏试验失败 | |
344 | G1\L86GLTB_ALM | GAS LEAK TEST OF GCV/VENT FAILED | 燃气泄漏试验排出失败 | |
349 | G1\L86GVA_ALM | INLET GUIDE VANE CONTROL TROUBLE | IGV控制故障 | |
350 | G1\L86N_ALM | ELECTRICAL TROUBLE - NORMAL SHUTDOWN | 电气故障-正常停机 | |
351 | G1\L86QE_ALM | DC PUMP ELECTRICAL TROUBLE START INHIBITED | 直流油泵电气故障禁止启动 | |
352 | G1\L86S | AUTO SYNCHRONIZING LOCKOUT | 自动同期装置闭锁 | |
353 | G1\L86TCI | COMPRESSOR INLET THERMOCOUPLE DISAGREE | 压气机进口热电偶不适合 | |
354 | G1\L86TFB_ALM | EXHAUST THERMOCOUPLES OPEN TRIP | 排气热电偶开路遮断 | |
355 | G1\L86TGT1_ALM | GENERATOR DIFFERENTIAL TRIP CHANNEL 1 | 发电机差动遮断1通道 | |
356 | G1\L86TGT2_ALM | GENERATOR DIFFERENTIAL TRIP CHANNEL 2 | 发电机差动遮断2通道 | |
357 | G1\L86TVA_ALM | INLET GUIDE VANE POSITION TROUBLE | IGV位置故障 | |
358 | G1\L86TXT_ALM | EXHAUST OVER TEMPERATURE TRIP | 排气超温遮断 | |
361 | G1\L86WW_ALM | OFF LINE COMP WW - USE RESET DISPLAY | 离线水洗-使用复位画面 | |
362 | G1\L90TKL_ALM | COOL SEAL AIR EXH BLOWERS LOAD DECREASE TROUBLE | 冷却密封风机负荷减少故障 | |
363 | G1\L94F1B_ALM | FIRE PROTECTION - CO2 RELEASED ZONE 1 | 火灾保护-CO2释放1区域 | |
364 | G1\L94F2B_ALM | FIRE PROTECTION - CO2 RELEASED ZONE 2 | 火灾保护-CO2释放2区域 | |
366 | G1\L94TC_ALM | STARTING MEANS TRQ CONVERTER DRAIN VALVE TROUBLE | 液力变扭器排放阀故障 | |
367 | G1\L94X_S_ALM | SHUTDOWN PAUSED - COMP BLD VLV POS FAIL | 停机时压气机防喘阀位置故障 | |
368 | G1\L94XZ_ALM | FIRED SHUTDOWN ABNORMAL SEQUENCE - TRIP | 停机火灾程序异常-遮断 | |
369 | G1\L96FG1_ALM | HEAT VENT 96FG-1 SENSOR TROUBLE | 加热口96FG-1传感器故障 | |
370 | G1\L96FGDIFF_AL | GAS FUEL PRESSURE TRANSMITTERS DIFFERENCE FAILURE | 燃气压力差别器故障 | |
371 | G1\L96FGH_ALM | FUEL GAS PRESSURE HIGH | 燃气压力高 | |
372 | G1\L96FGL_ALM | GAS FUEL SUPPLY PRESSURE LOW | 燃气供给压力低 | |
373 | G1\LAFPAP_SENSR | BAROMETRIC PRESSURE TRANSDUCERS DISAGREE | 大气压力传感器不合适 | |
374 | G1\LCPD_SENSR建筑实践 | COMPRESSOR DISCH XDUCER DIFF FAULT HIGH | 压气机排气压差高报警 | |
375 | G1\LCPRERR_ALM | COMP OP LIMIT PROTECTION MAX CTRL ERROR | 压气机压比错误 | |
376 | G1\LDWATT_ALM | MEGAWATT TRANSDUCER SIGNAL TROUBLE | 功率变送器信号故障 | |
377 | G1\LDWCAL_ALM | DWATT NONZERO WITH BREAKER OPEN | 开关断开而功率不为零 | |
379 | G1\LFPG2_SENSR | INTERVALVE PRESSURE TRANSDUCERS DISAGREE | 级间压力传感器不一致 | |
380 | G1\LFQGUV_ALM | GAS FUEL FLOW OUT OF RANGE | 燃气流量超范围 | |
381 | G1\LFSGRH_ALM | SRV OPEN AT 90 % - RISK OF TRIP ON HIGH EXH TEMP | 燃气速比阀开至90%-排气温度高有遮断危险 | |
382 | G1\LFSRCPR_ALM | COMP LIMIT FSR BACKUP CONTROL ACTIVE | 压气机工作极限控制备用FSR激活 | |
383 | G1\LFTG_ALM | GAS FUEL THERMOCOUPLE SIGNAL TROUBLE | 燃气热电偶信号故障 | |
387 | G1\LTBRGH_ALM | LUBE OIL TG TEMP FEED/RETURN DIFF HIGH | 轮机滑油供油/回油温差高 | |
388 | G1\LTBRGHH_ALM | LUBE OIL TG TEMP FEED/RETURN DIFF HIGH HIGH | 轮机滑油供油/回油温差高高 | |
389 | G1\LTGBRGH_ALM | LUBE OIL GEN TEMP FEED/RETURN DIFF HIGH | 发电机滑油供油/回油温差高 | |
390 | G1\LTGBRGHH_ALM | LUBE OIL GEN TEMP FEED/RETURN DIFF HIGH HIGH | 发电机滑油供油/回油温差高高 | |
391 | G1\LTNHLOSS_ALM | LOSS OF CTRL SPEED SIGNAL - START EMERG. LO PUMP | 丢失控制转速信号-启应急油泵 | |
392 | G1\LTTH1_ALM | LUBE OIL HEADER SENSOR#1 FAULT | 滑油母管#1温度传感器故障 | |
393 | G1\LTTH2_ALM | LUBE OIL HEADER SENSOR#2 FAULT | 滑油母管#2温度传感器故障 | |
394 | G1\LTTH3_ALM | LUBE OIL HEADER SENSOR#3 FAULT | 滑油母管#3温度传感器故障 | |
395 | G1\R5E_ALM | EMERGENCY REMOTE MANUAL TRIP | 远方手动紧急遮断 | |
396 | G1\XUCVXR0S02_A | <R> SLOT 2 UCVX DIAGNOSTIC ALARM | <R>机2通道UCVX诊断报警 | |
397 | G1\XUCVXS0S02_A | <S> SLOT 2 UCVX DIAGNOSTIC ALARM | <S>机2通道UCVX诊断报警 | |
398 | G1\XUCVXT0S02_A | <T> SLOT 2 UCVX DIAGNOSTIC ALARM | <T>机2通道UCVX诊断报警 | |
399 | G1\XVAICR0S04_A | <R> SLOT 4 VAIC DIAGNOSTIC ALARM | <R>机4通道VAIC诊断报警 | |
400 | G1\XVAICR0S06_A | <R> SLOT 6 VAIC DIAGNOSTIC ALARM | <R>机6通道VAIC诊断报警 | |
401 | G1\XVAICR0S08_A | <R> SLOT 8 VAIC DIAGNOSTIC ALARM | <R>机8通道猪肉榨菜VAIC诊断报警 | |
402 | G1\XVAICR0S15_A | <R> SLOT 15 VAIC DIAGNOSTIC ALARM | <R>机15通道VAIC诊断报警 | |
403 | G1\XVAICS0S04_A | <S> SLOT 4 VAIC DIAGNOSTIC ALARM | <S>机4通道VAIC诊断报警 | |
404 | G1\XVAICS0S06_A | <S> SLOT 6 VAIC DIAGNOSTIC ALARM | <S>机6通道VAIC诊断报警 | |
405 | G1\XVAICS0S15_A | <S> SLOT 15 VAIC DIAGNOSTIC ALARM | <S>机15通道VAIC诊断报警 | |
406 | G1\XVAICT0S04_A | <T> SLOT 4 VAIC DIAGNOSTIC ALARM | <T>机4通道VAIC诊断报警 | |
407 | G1\XVAICT0S06_A | <T> SLOT 6 VAIC DIAGNOSTIC ALARM | <T>机6通道VAIC诊断报警 | |
408 | G1\XVAICT0S15_A | <T> SLOT 15 VAIC DIAGNOSTIC ALARM | <T>机15通道VAIC诊断报警 | |
409 | G1\XVCMIR0S01_A | <R> SLOT 1 VCMI DIAGNOSTIC ALARM | <R>机1通道VCMI诊断报警 | |
410 | G1\XVCMIS0S01_A | <S> SLOT 1 VCMI DIAGNOSTIC ALARM | <S>机1通道VCMI诊断报警 | |
411 | G1\XVCMIT0S01_A | <T> SLOT 1 VCMI DIAGNOSTIC ALARM | <T>机1通道VCMI诊断报警 | |
412 | G1\XVCRCR0S09_A | <R> SLOT 9 VCRC DIAGNOSTIC ALARM | <R>机9通道VCRC诊断报警 | |
413 | G1\XVCRCR0S12_A | <R> SLOT 12 VCRC DIAGNOSTIC ALARM | <R>机12通道VCRC诊断报警 | |
414 | G1\XVCRCR0S13_A | <R> SLOT 13 VCRC DIAGNOSTIC ALARM | <R>机13通道VCRC诊断报警 | |
415 | G1\XVCRCR0S14_A | <R> SLOT 14 VCRC DIAGNOSTIC ALARM | <R>机14通道VCRC诊断报警 | |
416 | G1\XVCRCR0S17_A | <R> SLOT 17 VCRC DIAGNOSTIC ALARM | <R>机17通道VCRC诊断报警 | |
417 | G1\XVCRCR0S18_A | <R> SLOT 18 VCRC DIAGNOSTIC ALARM | <R>机18通道VCRC诊断报警 | |
418 | G1\XVCRCS0S09_A | <S> SLOT 9 VCRC DIAGNOSTIC ALARM | <S>机9通道VCRC诊断报警 | |
419 | G1\XVCRCS0S12_A | <S> SLOT 12 VCRC DIAGNOSTIC ALARM | <S>机12通道VCRC诊断报警 | |
420 | G1\XVCRCS0S13_A | <S> SLOT 13 VCRC DIAGNOSTIC ALARM | <S>机13通道VCRC诊断报警 | |
421 | G1\XVCRCS0S14_A | <S> SLOT 14 VCRC DIAGNOSTIC ALARM | <S>机14通道VCRC诊断报警 | |
422 | G1\XVCRCS0S17_A | <S> SLOT 17 VCRC DIAGNOSTIC ALARM | <S>机17通道VCRC诊断报警 | |
423 | G1\XVCRCS0S18_A | <S> SLOT 18 VCRC DIAGNOSTIC ALARM | <S>机18通道VCRC诊断报警 | |
424 | G1\XVCRCT0S09_A | <T> SLOT 9 VCRC DIAGNOSTIC ALARM | <T>机9通道VCRC诊断报警 | |
425 | G1\XVCRCT0S12_A | <T> SLOT 12 VCRC DIAGNOSTIC ALARM | <T>机12通道VCRC诊断报警 | |
426 | G1\XVCRCT0S13_A | <T> SLOT 13 VCRC DIAGNOSTIC ALARM | <T>机13通道VCRC诊断报警 | |
427 | G1\XVCRCT0S14_A | <T> SLOT 14 VCRC DIAGNOSTIC ALARM | <T>机14通道VCRC诊断报警 | |
428 | G1\XVCRCT0S17_A | <T> SLOT 17 VCRC DIAGNOSTIC ALARM | <T>机17通道VCRC诊断报警 | |
429 | G1\XVCRCT0S18_A | <T> SLOT 18 VCRC DIAGNOSTIC ALARM | <T>机18通道VCRC诊断报警 | |
430 | G1\XVPROR8S01_A | <X> VPRO DIAGNOSTIC ALARM | <X>通道诊断报警 | |
431 | G1\XVPROS8S02_A | <Y> VPRO DIAGNOSTIC ALARM | <Y>通道诊断报警 | |
432 | G1\XVPROT8S03_A | <Z> VPRO DIAGNOSTIC ALARM | <Z>通道诊断报警 | |
433 | G1\XVRTDR0S20_A | <R> SLOT 20 VRTD DIAGNOSTIC ALARM | <R>机20通道VRTD诊断报警 | |
434 | G1\XVRTDS0S20_A | <S> SLOT 20 VRTD DIAGNOSTIC ALARM | <S>机21通道VRTD诊断报警 | |
435 | G1\XVRTDT0S20_A | <T> SLOT 20 VRTD DIAGNOSTIC ALARM | <T>机22通道VRTD诊断报警 | |
436 | G1\XVSVOR0S05_A | <R> SLOT 5 VSVO DIAGNOSTIC ALARM | <R>机5通道VSVO诊断报警 | |
437 | G1\XVSVOR0S07_A | <R> SLOT 7 VSVO DIAGNOSTIC ALARM | <R>机7通道VSVO诊断报警 | |
438 | G1\XVSVOS0S05_A | <S> SLOT 5 VSVO DIAGNOSTIC ALARM | <S>机5通道VSVO诊断报警 | |
439 | G1\XVSVOS0S07_A | <S> SLOT 7 VSVO DIAGNOSTIC ALARM | <S>机7通道VSVO诊断报警 | |
440 | G1\XVSVOT0S05_A | <T> SLOT 5 VSVO DIAGNOSTIC ALARM | <T>机5通道VSVO诊断报警 | |
441 | G1\XVSVOT0S07_A | <T> SLOT 7 VSVO DIAGNOSTIC ALARM | <T>机7通道VSVO诊断报警 | |
442 | G1\XVTCCR0S19_A | <R> SLOT 19 VTCC DIAGNOSTIC ALARM | <R>机19通道VTCC诊断报警 | |
443 | G1\XVTCCR0S21_A | <R> SLOT 21 VTCC DIAGNOSTIC ALARM | <R>机21通道VTCC诊断报警 | |
444 | G1\XVTCCS0S21_A | <S> SLOT 21 VTCC DIAGNOSTIC ALARM | <S>机21通道VTCC诊断报警 | |
445 | G1\XVTCCT0S21_A | <T> SLOT 21 VTCC DIAGNOSTIC ALARM | <T>机21通道VTCC诊断报警 | |
446 | G1\XVTURR0S10_A | <R> SLOT 10 VTUR DIAGNOSTIC ALARM | <R>机10通道VTUR诊断报警 | |
447 | G1\XVTURS0S10_A | <S> SLOT 10 VTUR DIAGNOSTIC ALARM | <S>机10通道VTUR诊断报警 | |
448 | G1\XVTURT0S10_A | <T> SLOT 10 VTUR DIAGNOSTIC ALARM | <T>机10通道VTUR诊断报警 | |
449 | G1\XVVIBR0S16_A | <R> SLOT 16 VVIB DIAGNOSTIC ALARM | <R>机16通道VVIB诊断报警 | |
450 | G1\XVVIBS0S16_A | <S> SLOT 16 VVIB DIAGNOSTIC ALARM | <S>机16通道VVIB诊断报警 | |
451 | G1\XVVIBT0S16_A | <T> SLOT 16 VVIB DIAGNOSTIC ALARM | <T>机16通道VVIB诊断报警 | |
452 | G1\XVVIBT0S19_A | <T> SLOT 19 VVIB DIAGNOSTIC ALARM | <T>机19通道VVIB诊断报警 | |
459 | G1\L3CP_ALM | DAMPER CUSTOMER START INHIBIT | 挡板未打开启动被禁止 | |
460 | G1\L26HA11HH_AL | HEAT VENT VERY HIGH TEMP. IN DLN COMPARTMENT | DLN小间加热温度非常高 | |
461 | G1\L26HA11LL_AL | HEAT VENT VERY LOW TEMP. IN DLN COMPARTMENT | DLN小间通风温度非常低 | |
462 | 中国哪里最冷G1\L26HAHH_ALM | HEAT VENT VERY HIGH TEMP. IN AUXILIARY COMPARTMENT | 辅机间加热温度非常高 | |
463 | G1\L26HALL_ALM | HEAT VENT VERY LOW TEMP. IN AUXILIARY COMPARTMENT | 辅机间通风温度非常低 | |
464 | G1\L26HTHH_ALM | HEAT VENT VERY HIGH TEMP. IN TURBINE COMPARTMENT | 轮机间加热温度非常高 | |
465 | G1\L26HTLL_ALM | HEAT VENT VERY LOW TEMP. IN TURBINE COMPARTMENT | 轮机间通风温度非常低 | |
469 | G1\L33BT_ALM | HEAT VENT TURB COMPT VENT FLAP TROUBLE | 透平间通风振动故障 | |
473 | G1\L86BTX_ALM | HEAT VENT LOSS OF TURB. COMP. VENT.- FAST SHUTDOWN | 丢失透平冷却风机-立即停机 | |
474 | G1\L86VLX_ALM | HEAT VENT LOSS OF DLN COMPARTMENT VENTILATION | 丢失DLN小间通风装置 | |
479 | G1\L26HGHH_ALM | HEAT VENT VERY HIGH TEMP. IN LOAD COMPARTMENT | 负荷连轴节间通风温度非常低 | |
480 | G1\L26HGLL_ALM | HEAT VENT VERY LOW TEMP. IN LOAD COMPARTMENT | 负荷连轴节间加热温度非常高 | |
484 | G1\L30HG1X_ALM | GENETATOR SPACE HEATER IN TROUBLE | 发电机加热器故障 | |
485 | G1\L30VG_ALM | HEAT VENT LOAD COMPARTMENT VENT. ELECTRICAL FAULT | 负荷联轴节间通风机电气故障 | |
486 | G1\L30VGX_ALM | HEAT VENT LOAD COMPARTMENT VENT. CHANGE OVER | 负荷联轴节间通风机切换 | |
490 | G1\L33VG_ALM | 初中数学复习HEAT VENT LOAD COMPT VENT FLAP TROUBLE | 负荷联轴节间通风机振动故障 | |
491 | G1\L33VS411C_AL | GAS FUEL SHUT OFF VALVE LIMIT SWITCH NOT CLOSED | 燃气截止阀限位开关未关闭 | |
492 | G1\L33VS411CX_A | GAS FUEL SHUT OFF VALVE CLOSED TROUBLE | 燃气截止阀关闭故障 | |
493 | G1\L33VS421O_AL | GAS FUEL SHUT OFF VALVE LIMIT SWITCH NOT OPEN | 燃气截止阀限位开关未打开 | |
494 | G1\L33VS421OX_A | GAS FUEL SHUT OFF VALVE OPEN TROUBLE | 燃气截止阀打开故障 | |
498 | G1\L52VG_ALM | HEAT VENT LOAD COMPARTMENT VENT. FAULT | 负荷间排气风机故障 | |
515 | G1\L86VGX_ALM | HEAT VENT LOSS OF LOAD COMPARTMENT VENTILATION | 丢失负荷间通风装置 | |
523 | G1\FPG20A_SENSR | GCV 1 PRESSURE TRANSDUCER FAULT | GCV1压力传感器故障 | |
524 | G1\FPG21A_SENSR | GCV 2 PRESSURE TRANSDUCER FAULT | GCV2压力传感器故障 | |
525 | G1\FPG22A_SENSR | GCV 3 PRESSURE TRANSDUCER FAULT | GCV3压力传感器故障 | |
526 | G1\L26FT2G_ALM | FUEL GAS INTERVALVE TEMP TC TROUBLE | 燃气进口阀温度测点故障 | |
533 | G1\L27BLN21_ALM | BAT CHAR 2 AC UNDERVOLT - T.D. NORMAL SD | 2蓄电池交流低电压 | |
534 | G1\L27BLN22_ALM | BAT CHAR 2 AC UNDERVOLT - INSTANT NORMAL SD | 2蓄电池交流低电压-瞬间正常 | |
535 | G1\L27BLN23_ALM | BATTERY CHARGER 2 AC UNDERVOLTAGE - SHUTDOWN | 2蓄电池交流低电压-停机 | |
538 | G1\L27X1_ALM | G60A PROTECTION POWER SUPPLY FAULT | G60A保护电源故障 | |
539 | G1\L27X2_ALM | G60B PROTECTION POWER SUPPLY FAULT | G60B保护电源故障 | |
540 | G1\L28FPDON_ALM | PRIMARY FLAME DETECTOR ON ALARM | 初级火焰探测器报警 | |
541 | G1\L28FSD_ALM | SECONDARY FLAME DETECTOR TROUBLE ALARM | 二级火焰探测器报警 | |
542 | G1\L30BSA_ALM | BEARING SEAL AIR VALVE TROUBLE | 轴承密封空气阀故障 | |
543 | G1\L30COM_EXFLT | EXCITER TO MKVI COMMUNICATION FAULT | 励磁到MKVI通讯故障 | |
544 | G1\L30EX_FSP | EXCITER FAILURE TO STOP | 励磁故障停机 | |
545 | G1\L30EX_FTS | EXCITER FAILURE TO START | 励磁故障启动 | |
546 | G1\L30EX_RS | EXCITER NOT READY TO START | 励磁未准备好启动 | |
548 | G1\L30FPDAR_ALM | COMBUSTION PRIMARY ZONE AUTO REIGNITION | 燃烧区域初次自动点火 | |
549 | G1\L30FQRG1ER_A | FUEL G1 Cv REF OUT OF LIMITS - AUTO LOW | 燃料G1极限热值低 | |
550 | G1\L30FQRG2ER_A | FUEL G2 Cv REF OUT OF LIMITS - AUTO LOW | 燃料G2极限热值低 | |
551 | G1\L30FQRG2PF_A | G2 MANIFOLD PPRESSURE TRANSDUCER TROUBLE | G2压力传感器故障 | |
552 | G1\L30FQRG3ER_A | FUEL G3 Cv REF OUT OF LIMITS - AUTO LOW | 燃料G3极限热值低 | |
553 | G1\L30FQRG3PF_A | G3 MANIFOLD PRESSURE TRANSDUCER TROUBLE | G3压力传感器故障 | |
556 | G1\L30FX1_ALM | FAILURE TO FLAME OUT PRIMARY ZONE - ALARM | 燃烧区域初次点火故障报警 | |
557 | G1\L30FX2_ALM | FAILURE TO REIGNITE PRIMARY ZONE - ALARM | 燃烧区域再次点火故障报警 | |
558 | G1\L30FX3_ALM | FAIL TO RE-IGN PRIM IN SEC L.R. - ALARM | 区域燃烧模式选择故障报警 | |
559 | G1\L30FXML_ALM | DLN PREMIX MODELESS - GOTO SEC LOAD REC | DLN从预混状态转到负荷状态 | |
560 | G1\L30FXP1_ALM | FAIL TO LEAVE PREMIX XFER - GOTO L-L | 未经预混状态转到L-L状态 | |
561 | G1\L30G60A_ALM | G60A GENERAL FAULT | G60A整体报警 | |
562 | G1\L30G60B_ALM | G60B GENERAL FAULT | G60B整体报警 | |
563 | G1\L30MRSYNC_AL | SYNC INHIBITED - EX MAN REG ACTIVE | 同期禁止-励磁手动激活 | |
564 | G1\L30PGTOF_ALM | GAS FUEL XFER PURGE VALVE FAILURE TO OPEN | 燃气清吹阀打开故障 | |
565 | G1\L30QB_ALM | GENERATOR LIFT BEARING LIFT PUMP CHANGE OVER ALM | 发电机顶轴油泵切换故障 | |
566 | G1\L30QVX_ALM | LUBE OIL MIST ELIM FAULT - CHANGE OVER | 油雾分离机故障-切换 | |
567 | G1\L30TXAH1 | FIRST FAILED HIGH EXHAUST THERMOCOUPLE | 首次点火不成功排气温度高 | |
568 | G1\L33TH3_ALM | IBH MANUAL ISOLATION VALVE NOT OPEN | IBH手动隔离阀未打开 | |
569 | G1\L33TH4C_ALM | BLEED DRAIN VALVE FAILURE TO CLOSE | 排污阀关闭故障 | |
570 | G1\L3AFDEP_ALM | EXHAUST PRESSURE TRANSDUCER TROUBLE | 排气压力传感器故障 | |
571 | G1\L3BHF1_ALM | IBH CONTROL VALVE NOT TRACKING | IBH控制阀未跟踪 | |
572 | G1\L3BHF3_ALM | COMP OPERATING LIMIT CONTROL FAULT | 压气机工作极限控制故障 | |
573 | G1\L3BHFT_ALM | BLEED HEAT SYSTEM NOT OPERATIONAL - TRIP | 进气加热系统为投运-遮断 | |
574 | G1\L3GCV3A_ALM | GCV3 NOT FOLLOWING REF ALARM | 燃气控制阀GCV3未跟踪报警 | |
575 | G1\L3GCV3FLT_A | GCV3 GAS CONTROL VLV SERVO TROUBLE ALARM | 燃气控制阀GCV3伺服故障报警 | |
576 | G1\L3GCVSA_ALM | G2 GCV NOT FOLLOWING REF ALARM | 燃气控制阀GCV2未跟踪报警 | |
577 | G1\L3GCVSFLT_A | SEC GAS CONTROL VLV SERVO TROUBLE ALARM | 燃气控制阀GCV2伺服故障报警 | |
578 | G1\L3GFIVPH_ALM | P2 SUPPLY PRESSURE TOO HIGH FOR STARTUP | 启动过程中P2压力太高 | |
579 | G1\L3GFIVPL_ALM | P2 SUPPLY PRESSURE TOO LOW FOR START UP | 启动过程中P2压力太低 | |
580 | G1\L43EX_ALM | EX2K MANUAL (FVR) REGULATOR ACTIVE | 励磁手动激活 | |
582 | G1\L4DLNT_ALM | DRY LOW NOx SYSTEM TROUBLE - TRIP | DLN系统故障-遮断 | |
583 | G1\L4EXOFF_ALM | EX2K OPERATOR SELECTED EXCITATION OFF | 励磁操作选择停止方式 | |
584 | G1\L4GFIVPT_ALM | P2 SUPPLY PRESSURE TOO LOW TRIP | P2压力太低遮断 | |
586 | G1\L60GC1FSH_A | GAS CTRL VLV TOO FAR OPEN - ABORT START | 燃气控制阀开度过限-启动失败 | |
587 | G1\L63PG2H_ALM | GAS TRANSFER PURGE SYSTEM HIGH PRESS | 燃气轻吹系统压力高 | |
588 | G1\L63QB1L_ALM | GENERATOR LIFT LIFTING OUTPUT LOW PRESSURE ALM | 发电机顶轴油泵出口压力低报警 | |
591 | G1\L83FQG1NC_AL | FQCV #1 RUNNING NON-CRITICAL MODE | FQCV#1运行-临界模式 | |
592 | G1\L83FQG2NC_AL | FQCV #2 RUNNING NON-CRITICAL MODE | FQCV#2运行-临界模式 | |
593 | G1\L83FQG3NC_AL | FQCV #3 RUNNING NON-CRITICAL MODE | FQCV#3运行-临界模式 | |
595 | G1\L83LLBM_ALM | LEAN-LEAN BASE MODE SELECTED | L-L燃烧模式选择 | |
596 | G1\L83LLEXT_ALM | EXTEND L-L MODE HIGH EMISSIONS - ALARM | 进入扩展L-L模式-报警 | |
598 | G1\L86BQ_ALM | BEARING SEAL AIR VALVE POSITION TROUBLE | 轴承密封空气阀位置故障 | |
605 | G1\L86GCV3T_ALM | G3 GCV NOT FOLLOWING REF TRIP | 燃气控制阀GCV3未跟踪遮断 | |
606 | G1\L86GCVST_ALM | G2 GCV NOT FOLLOWING REF TRIP | 燃气控制阀GCV2未跟踪遮断 | |
609 | G1\L86PGTLO_ALM | GAS XFER PURGE VALVE FAILURE TO CLOSE | 燃气轻吹阀关闭故障 | |
610 | G1\L86PGVL_ALM | XFER PRG VLV FAILED TO OPEN-LOWER LOAD | 燃气轻吹阀打开故障-降负荷 | |
613 | G1\L86QB_ALM | GENERATOR LIFT LOSS OF BEARING LIFT PUMPS ALARM | 发电机顶轴油泵故障报警 | |
614 | G1\L86QBLO_ALM | GENERATOR LIFT LUBE OIL PUMPS LOCKOUT ALARM | 发电机顶轴油泵闭锁报警 | |
615 | G1\L86QVX_ALM | LUBE OIL MIST ELIM FANS LOSS - SD | 油雾风机丢失 | |
616 | G1\L94DP1_ALM | G60A CRITICAL FAILURE | 发电机保护柜G60A严重故障 | |
617 | G1\L94DP2_ALM | G60B CRITICAL FAILURE | 发电机保护柜G60B严重故障 | |
618 | G1\L94FX1_ALM | FAILURE TO LEAVE SECONDARY XFER - TRIP | 二级燃烧转换模式故障-遮断 | |
619 | G1\L94FX2_ALM | FAILURE TO REIGNITE PRIMARY ZONE - TRIP | 一级燃烧点火失败-遮断 | |
620 | G1\L94FX3_ALM | FAIL TO REIGNITE PRIM IN SEC - L.R. TRIP | 二次点火失败-L.R.遮断 | |
621 | G1\L94FX4_ALM | FAILURE TO LEAVE PREMIX TRANSFER - TRIP | 预混转换失败-遮断 | |
622 | G1\L94GEN | GENERATOR TROUBLE SHUTDOWN | 发电机故障-停机 | |
623 | G1\L94GSDW_ALM | COMBUSTION PROTECTION SHUTDOWN LOCKOUT | 燃烧保护停机闭锁 | |
624 | G1\LCPBHP_ALM | IBH PRESSURE TRANSDUCER FAULT | IBH压力传感器故障 | |
625 | G1\LFAG1NBA_A | GCV 1 REG AT NULL COMP AUTHORITY LIMIT | GCV1零位补偿超限 | |
626 | G1\LFAG2NBA_A | GCV 2 REG AT NULL COMP AUTHORITY LIMIT | GCV2零位补偿超限 | |
627 | G1\LFAG3NBA_A | GCV 3 REG AT NULL COMP AUTHORITY LIMIT | GCV3零位补偿超限 | |
629 | G1\L33THFLT_ALM | INLET BLEED HEATING VALVE POSITION TROUBLE | 进气加热IBH位置故障 | |
630 | G1\L30CSX_ALM | CUSTOMER COOLING SYSTEM FAULT | 主冷却系统故障 | |
632 | G1\L30AC1_ALM | 400VAC POWER SUPPLY FAULT #1 | 400V交流电源#1故障 | |
633 | G1\L30AC2_ALM | 230VAC NORMAL POWER SUPPLY FAULT #2 | 230V交流电源#2故障 | |
634 | G1\L30AC3_ALM | 230VAC UPS POWER SUPPLY FAULT #3 | 230V交流电源#3故障 | |
635 | G1\L30AC4_ALM | 115VAC POWER SUPPLY FAULT #4 | 115V交流电源#4故障 | |
636 | G1\L30BB_ALM | DAMPER OUT OF ORDER | 挡板故障 | |
637 | G1\L30UPSCS_ALM | INVERTER STATIC CONVERTER GROUP FAULT | 逆变器静止转换器故障 | |
638 | G1\L30UPSMAN_AL | UPS SYSTEM OUT OF ORDER | UPS系统故障 | |
639 | G1\L30UPSMIN_AL | INVERTER MINOR GROUP FAULT | 逆变器小模块故障 | |
640 | G1\L30UPSMOD_AL | INVERTER MODULE GROUP FAULT | 逆变器单元故障 | |
641 | G1\LALM_PO_ALM | AIR FILTER ALARM PANEL OPEN | 空气过滤器故障打开面板 | |
642 | G1\L71WG2_ALM | GENERATOR LIQUID LEVEL DETECTOR 2# NDE | #2发电机漏液检测有液体 | |
643 | G1\L3DWRF | LOSS OF EXTERNAL SETPOINT LOAD SIGNAL | 丢失外部预选负荷信号 | |
644 | G1\L30CR_ALM | STARTING MEANS CRANKING MOTOR FAULT | 启动马达故障 | |
645 | G1\L43CR_ALM | STARTING MEANS CRANKING MOTOR LOCAL POSITION | 启动马达就地状态故障 | |
646 | G1\L30SG1_ALM | EXCITER CHANNEL FAILED WITH IGNITOR ON | 点火过程中励磁通道故障 | |
652 | G1\L45FP4_ALM | FIRE PROTECTION - FIRE PRE ALARM ZONE 4 | 火灾保护-4区火灾预报警 | |
653 | G1\L45FTX4_ALM | FIRE PROTECTION - FIRE ALARM ZONE 4 | 火灾保护-4区火灾报警 | |
654 | G1\L94F4B_ALM | FIRE PROTECTION - CO2 RELEASED ZONE 4 | 火灾保护-4区CO2释放 | |
662 | G1\L4TFHH_ALM | FLOW INLET FILTER DIFF PRESSURE HIGH TRIP | 进气滤压差高遮断 | |
663 | G1\L63TF2H_ALM | FLOW INLET FILTER DIFF PRESSURE HIGH | 进气滤压差高 | |
664 | G1\R5E1_ALM | REMOTE EMERGENCY TRIP PUSH BUTTON 1 - LCR DESK | 远方紧急遮断#1按钮按下-控制台 | |
665 | G1\R5E3_ALM | REMOTE EMERGENCY TRIP SIGNAL 1 - DCS SYSTEM | 远方紧急遮断信号#1-DCS系统 | |
666 | G1\L52MCB_ALM | FUSE FAULT ON UNDERVOLTAGE RELAY | 低电压继电器保险丝故障 | |
667 | G1\L86MON_ALM | 74/86 LOCK OUT RELAYS COIL | 发电机保护柜74/86继电器闭锁线圈故障 | |
668 | G1\L86G2AB_ALM | LOCKOUT RELAY 74/86-2A&2BTRIP TO EXCITATION | 励磁系统闭锁线圈74/86-2A&2B遮断 | |
670 | G1\LMX3_ALM | GENERATOR PROTECTION MX3 WATCHDOG | 发电机保护MX3监视 | |
671 | G1\L26GGCA_ALM | GENERATOR COLD GAS TEMPERATURE HIGH | 发电机冷风温度高 | |
672 | G1\L26GGCAH_ALM | GENERATOR COLD GAS TEMPERATURE HIGH | 发电机冷风温度高 | |
673 | G1\L26GGCF_ALM | GENERATOR COLD GAS RTD OUT OF LIMIT FAILURE | 发电机冷风RTD出口极限故障 | |
674 | G1\L26GGH17_ALM | EXCITER HOT GAS TEMPERATURE HIGH | 励磁热风温度高 | |
675 | G1\L26GGHA_ALM | GENERATOR HOT GAS TEMPERATURE HIGH | 发电机热风温度高 | |
676 | G1\L26GGHF7_ALM | EXCITER HOT GAS RTD OUT OF LIMIT FAILURE | 励磁热风RTD出口极限故障 | |
677 | G1\L26GGHF_ALM | GENERATOR HOT GAS RTD OUT OF LIMIT FAILURE | 发电机热风RTD出口极限故障 | |
678 | G1\L26GGHH7_ALM | EXCITER HOT GAS TEMPERATURE HIGH NSD | 励磁热风温度高NSD | |
679 | G1\L26GGHHA_ALM | GENERATOR HOT GAS TEMPERATURE HIGH | 发电机热风温度非常高 | |
680 | G1\L26GSAF1_ALM | STATOR COLLECTOR END RTD FAILURE | 定子终端RTD故障 | |
681 | G1\L26GSAF2_ALM | STATOR COLLECTOR END RTD FAILURE NSD | 定子终端RTD故障NSD | |
682 | G1\L26GSAH_ALM | GENERATOR STATOR COLLECTOR END TEMP HIGH | 发电机定子终端温度高 | |
683 | G1\L26GSAHH_ALM | GENERATOR STATOR COLLECTOR END TEMP HIGH | 发电机定子终端温度非常高 | |
684 | G1\L26GSFF1_ALM | STATOR COLLECTOR END RTD FAILURE | 定子终端RTD故障 | |
685 | G1\L26GSFF2_ALM | STATOR COLLECTOR END RTD FAILURE NSD | 定子终端RTD故障NSD | |
686 | G1\L26GSFH_ALM | GENERATOR STATOR COUPLING END TEMP HIGH | 发电机定子终端温度高 | |
687 | G1\L26GSFHH_ALM | GENERATOR STATOR COUPLING END TEMP HIGH | 发电机定子终端温度非常高 | |
688 | G1\L52QB_ALM | GENERATOR LIFT STANDBY BEAR LIFT OIL PMP RUNN | 发电机顶轴油泵运行 | |
689 | G1\L63QB2L_ALM | GENERATOR LIFT LIFTING OUTPUT LOW PRESSURE ALM | 发电机顶轴油泵出口压力低报警 | |
690 | G1\L33EF_ALM | HEAT VENT EXHAUST COMPT VENT FLAP TROUBLE | 排气框架通风故障 | |
691 | G1\L52EF_ALM | HEAT VENT EXHAUST COMPARTMENT VENT. FAULT | 排气框架通风机故障 | |
693 | G1\L39VS2A_ALM | VIB BN GT BRG #2 RADIAL SHAFT DISPLACEMENT ALERT | 透平#2轴承振动大报警 | |
694 | G1\L39VS2D_ALM | VIB BN GT BRG #2 RADIAL SHAFT DISPLACEMENT DANGER | 透平#2轴承振动大危险 | |
695 | G1\L30GVX_ALM | HEAT VENT GENERATOR COMPARTMENT VENT. CHANGE OVER | 发电机间冷却风机切换 | |
696 | G1\L52GV_ALM | HEAT VENT GENERATOR COMPARTMENT VENT. FAULT | 发电机间冷却风机故障 | |
697 | G1\L86GVX_ALM | HEAT VENT LOSS OF GENERATO COMPARTMENT VENTILATION | 丢失发电机间通风设备 | |
704 | G1\L30DC1_ALM | 125VDC POWER SUPPLY FAULT #1 | 125V直流电源故障#1 | |
705 | G1\L63QQ20H_ALM | LUBE OIL MIST ELIM FILTER HIGH DIFF PRESSURE | 油雾分离器滤网压差高 | |
708 | G1\L86EFX_ALM | HEAT VENT LOSS OF BUILDING VENTILATION | 丢失隔音罩通风装置 | |
709 | G1\L30QBX1_ALM | GENERATOR LIFT BEARING LIFT PUMP CHANGE OVER ALM | 发电机顶轴油泵#1切换故障 | |
710 | G1\L30QBX2_ALM | GENERATOR LIFT BEARING LIFT PUMP CHANGE OVER ALM | 发电机顶轴油泵#2大连一方切换故障 | |
711 | G1\L30QVX1_ALM | LUBE OIL MIST ELIM FAULT - CHANGE OVER | 滑油油雾分离机#1故障-切换 | |
712 | G1\L30QVX2_ALM | LUBE OIL MIST ELIM FAULT - CHANGE OVER | 滑油油雾分离机#2故障-切换 | |
713 | G1\L26BATH_ALM | BATTERY COMPARTMENT HIGH TEMP | 蓄电池间温度高 | |
714 | G1\L26BATL_ALM | BATTERY COMPARTMENT LOW TEMP | 蓄电池间温度低 | |
715 | G1\LMCBTRIP_ALM | MCB- TRIPPED | MCB-遮断 | |
716 | G1\LSPRINGCH_AL | SPRING NOT CHARGED ALARM | 机械装置未切换故障 | |
717 | G1\L63CBL1_ALM | CO2 LOSS GAS ZONE 1 | 1区域丢失CO2气体 | |
718 | G1\L63CBL2_ALM | CO2 LOSS GAS ZONE 2 | 2区域丢失CO2气体 | |
719 | G1\L63CBL4_ALM | CO2 LOSS GAS ZONE 4 | 4区域丢失CO2气体 | |
720 | G1\LSYNMEAS1FLT | SYNCH VOLT REFERENCE FAULT (1YH) | 同期电压参考故障（1YH） | |
721 | G1\LSYNMEAS2FLT | SYNCH VOLT REFERENCE FAULT (3YH) | 同期电压参考故障（3YH） | |
722 | G1\L30MT_ALM | NORMAL STOPPING UNIT FROM CUSTOMER TRANSFORMER | 主变停止装置正常 | |
723 | G1\L33CL1_ALM | FIRE PROTECTION - CO2 LOCKED OFF IN ZONE 1 | 火灾保护-1区域CO2闭锁 | |
724 | G1\L33CL2_ALM | FIRE PROTECTION - CO2 LOCKED OFF IN ZONE 2 | 火灾保护-2区域CO2闭锁 | |
725 | G1\L33CL4_ALM | FIRE PROTECTION - CO2 LOCKED OFF IN ZONE 4 | 火灾保护-4区域CO2闭锁 | |
726 | G1\L33DH1_ALM | DIVERTER HSRG CLOSED | 烟气挡板关闭 | |
727 | G1\L63ATJB_ALM | PERF MONITORING INSTRUM BOX VERY LOW TEMP | 监视仪表盘温度非常低 | |
728 | G1\R5E2_ALM | REMOTE EMERGENCY TRIP PUSH BUTTON 2 - LCR DESK | 远方#2紧急遮断按钮按下-控制台 | |
729 | G1\R5E4_ALM | REMOTE EMERGENCY TRIP SIGNAL 2 - DCS SYSTEM | 远方#2紧急遮断按钮按下-DCS系统 | |
730 | G1\L74HT1_ALM | CONTROL COMPARTMENT TEMP HIGH | 控制室温度高 | |
731 | G1\L74HT2_ALM | CONTROL COMPARTMENT TEMP LOW | 控制室温度低 | |
732 | G1\L27BLX_ALM | BATTERY SUPPLY FAULT | 蓄电池供给故障 | |
733 | G1\L30HG2_ALM | FAULT FEEDER Q60 SPACE HEATER FOR GLAC | Q60馈线柜加热器故障太冷 | |
734 | G1\L30HG3_ALM | FAULT FEEDER Q62 SPACE HEATER FOR GNAC | Q62馈线柜加热器故障太热 | |
735 | G1\L96QV1H_ALM | LUBE OIL MIST ELIM HIGH DIFFERENTIAL PRESSURE | 油雾分离机滤网压差高 | |
736 | G1\L96QV1L_ALM | LUBE OIL MIST ELIM LOW DIFFERENTIAL PRESSURE | 油雾分离机滤网压差低 | |
737 | G1\R_IO_STATE_A | R PROCESSOR OFFLINE ALARM | R离线数据故障 | |
738 | G1\S_IO_STATE_A | S PROCESSOR OFFLINE ALARM | S离线数据故障 | |
739 | G1\T_IO_STATE_A | T PROCESSOR OFFLINE ALARM | T离线数据故障 | |
本文发布于:2023-05-23 11:23:56，感谢您对本站的认可！
本文链接：https://www.wtabcd.cn/fanwen/fan/89/924967.html
版权声明：本站内容均来自互联网，仅供演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系，我们将在24小时内删除。
| 留言与评论（共有 0 条评论） |
