机械手故障

更新时间:2023-05-22 01:22:11 阅读：评论：0

大连好玩的地方小主持人自我介绍军官待遇霸气业绩冲刺口号砂锅白菜炖豆腐

The mold does not	1) Is the vertical cylinder descending?	1) Press the Up key to rai the vertical
clo	2) Does the productconfirmation	cylinder
	limit switch come on after the	2) Adjust the limit switch and check the wiring
模具不关闭	product is chunked automatically?	3) Check the ON conditions and the interlock
	3) Is the mold clo safety signal	4) Check the ON conditions to e if they are
	comes on?	correct.
	4) Is the cycle start display ON?
		1) 使用操作面板的上来上升机械手
	1) 机械手是否竖直下降	2) 检查限位开关及相关连线
	2) 产品被夹住后产品确认限位开关是否	3) 检查ON的条件和互锁
	自动转ON	4) 检查ON的条件是否满足
	3) 模具关闭安全信号是否转ON?
	4) 周期开始的显示是否为ON?
The Mold does not	1) Is the vertical cylinder descending?	1) Press the Up key to rai the vertical cylinder
open	2) Is the mold open safety signal	2) Check the On conditions and the interlock
模具不开	comes on?
		1) 使用操作面板的上来上升机械手
	1) 机械手是否竖直下降?	2) 检查ON的条件是否满足
	2) 模具关闭安全信号是否转ON?
No descent movement	1) Is the mold open conplete (MO)	1) Adjust the limit switch on the molding
无下降动作	signal comes on?(extracting-side)	machine and check the wiring of the
	2) Are the swing action-end and swing	control box.
	return-end limit switches(on the	2) Adjust the limit switch on the molding machine
	extracting and relea side) function	and check the wiring.
	correctly?	3) Loon gradually until descent movement starts.
	3) Is the dent speed control valve shut	4) Replace bad valve.
	too tightly?	5) See the ction"Manual Operations" and
	4) Is the solenoid valve bad?	"Automatic Operations"
	5) Have the input condifions been met?	6) Replace bent hoss.
	6) Is the air ho bent?	7) Replace the packing.
	7) Is the packing inside the cylinder
	damaged?	1) 调整注塑机的限位开关并检查到控制盒的连线
		2) 调整注塑机的限位开关并检查相关连线
	1) 模开完成信号(MO)是否为ON	3) 逐渐松动阀门直到机械手开始下降
	2) 机械手摆动复归和摆动到位的限位开	4) 更换损坏的阀门
	关是否工作正常?	5) 参看有关“手动操作“和“自动操作”
	3) 机械手下降速度控制气阀是否锁得太	6）更换损坏的气管
	紧?	7) 更换密封
	4) 电磁阀是否损坏？
	5) 是否满足输入条件？
	6) 气管是否被弯曲？
	后视镜怎么调最好图解7) 气缸内部密封是否损坏？
No advance	1) Have the input conditions been met?	1) See the ction "Manual Operations" and
movement	2) Is the advance speed control valve shut	"Automatic Operations"
	too tightly?	2) Loon gradually until advance movement
无前进动作	3) Is the solenoid valve bad?	start
	4) Is the air ho bent?	3) Replace bad valve
	5) Is the packing inside the cylinder damaged?	4) Replace bent ho.
		5) Replace the packing
	1) 输入条件是否满足？
	2) 前进的速度控制阀门是否关得太*？	1) 参看“手动操作”和“自动操作”
	3) 电磁阀门是否损坏？	2) 逐渐松动阀门直到机械手开始前进
	4) 气管是否被弯曲？	3) 更换损坏的阀门
	5) 气缸内部密封是否损坏？	4) 更换气管
		5) 更换密封
The Product is not	1) Are the input conditions met?	1) See the ction "Manual Operations" and
gripped	2) The chuck cylinder is defective?	"Automatic Operations"
	3) The solenoid valve is defective?	2) Replace the chuck cylinder
产品未抓紧	4) Is the molding machine mold open stroke correct?	3) Replace the solenoid valve
	5) Is the uploader crosswi stroke correct?	4) Adjust the molding open of molding machine.
	6) Is the protrusion of ejector pin appropriate?Is the	5) Adjust the crosswi stroke.
	tting time on the timer appropriate?	6) Adjust the ejector advance stroke on the molding
	7) The ho for the chuck pipe is loo.	machine side
	8) Has mold paration deteriorated?	7) If the ho is loo, replace it with now one.
		8) Apply mold paration solution or repair the metal
	1) 输入条件是否满足？	mold.
儿童卧房	2) 产品夹的气筒是否损坏？
	3) 电磁阀是否损坏？	1) 参看“手动操作”和“自动操作”
	4) 注塑机的模开行程是否正确？	2) 更换夹子的气筒
	5) 机械手的摆动行程是否正确？	3) 更换电磁阀
	6) 顶针的顶出是否合适？定时器的时间设定是否合适?	4) 调整注塑机的开模
	7) 夹子的气管是否松？	5) 调整摆动行程
	8) 开模情况是否恶化	6) 调整注塑机的顶针顶出行程
	普通话英语	7) 如果气管松，更换新的
		8) 修理模具
No return	1) Have the input conditions been met?	1) See the ction "Manual Operation"...
movement	2) Are the swing action-end and swing return-end limit	2) Adjust the limit switch on the molding machine
	switches(on the extracting and relea side)	and check the wiring.
无回位	function correctlly?	3) Replace bad valve
	3) Is the solenoid valve bad?
		1) 参看“手动操作”和“自动操作”
	1) 输入条件是否满足?	2) 调整注塑机的限位开关并检查相关连线
	2) 机械手摆动复归和摆动到位的限位开关是否正常?	3) 更换坏的电磁阀
	3) 电磁阀是否损坏?
No ascent	1) Have the input conditions been met?	1) See the ction "Manual Operation"...
	2) Is the ascent speed control valve shut too tightly?	2) Loon gradually until ascent movement
无上升	3) Is the solenoid valve bad?	starts
		3) Replace bad valve
	1) 输入条件是否满足?
	2) 上升速度控制阀门是否关得太警？	1) 参看“手动操作”和“自动操作”
	3) 电磁阀是否损坏?	2) 逐渐松动阀门直到机械手开始上升
		3) 更换坏的电磁阀
No swing	1) Are swing-action and swing-return signal being	1) Refer to ction "Manual Operation"...
	output?	2) Loon gradually until swing starts
无摆动	2) Is swing speed control valve shut too tightly?	3) Replace bad valve
	3) Is solenoid valve bad?	4) Replace bent ho.
	4) Is the air ho bent?	5) Replace bad packing.
	5) Is cylinder packing bad?
		1) Refer to ction "Manual Operation"...
	1) 摆动复归及摆动到位?	2) 逐渐松动阀门直到机械手开始摆动
	2) 摆动的速度控制阀门是否关得太紧?	3) 更换坏的阀门
	3) 电磁阀是否损坏?	4) 更换气管
	4) 气管是否弯曲？	5) 更换密封
	5) 气筒内密封是否损坏？
Swing stops midway	1) Does Product-Confirmation signal go OFF during	1) Check limit-switch tting and wiring.
	swing?	2) Check limit-switch tting and wiring.
机械手摆动中途停止	2) Are ascent-end and return-end switches OFF?
		1) 检查限位开关和相关连线
	1) 机械手摆动过程中产品确认信号是否变OFF	2) 检查限位开关及相关连线
	2) 上升结束和回位开关是否变OFF?

本文发布于:2023-05-22 01:22:11，感谢您对本站的认可！

本文链接：https://www.wtabcd.cn/fanwen/fan/89/922726.html

上一篇：IBPHYSICSSL

下一篇：三维动画术语中英文对照

标签：是否机械手摆动开关阀门

留言与评论（共有 0 条评论）