Company number：【WTUT-WT88Y-W8BBGB-BWYTT-19998】
注塑机专业英语
钣金 machine cover / upper cover/ side cover
锁模部分 clamping unit
射胶部分 injection unit
机架 machine frame / ba
电气系统 electric system
液压系统 hydraulic system
机械系统 mechanical system
机门 safety door / fixed door / movable door
锁模部分 clamping unit
电脑控制器 computer controller
机械安全锁 mechanical safety interlock
射胶部分 injection unit
液压系统 hydraulic system
电箱 electrical cabinet / cable
机架分体线 stand split line
机架螺丝孔 foundation bolt hole
机架 machine ba / supporting frame
理论注射容积 theoretical shot volume
实际注射量 shot weight
螺杆直径 screw diameter公司宣言
注射压力 injection pressure
注射速度 injection speed
注射速率 injection rate
螺杆长径比 screw L/D ratio
螺杆行程 screw stroke
螺杆转速 screw speed
熔胶能力 plasticizing capacity
锁模力 clamping force
开模/锁模行程 mold clamping / opening stroke
模板尺寸 platen size
拉杆间距 distance between tie bars / rods
模板最大距离 max. daylight
杯龙容模量 mold thickness (min. & max.)
顶出行程 hydraulic ejection stroke
顶出力 hydraulic ejection force
顶针数 nos. of ejector pin
液压系统压力 hydraulic system pressure
油泵马达 pump motor
电热量 heating capacity
温度控制区数 nos. of temp control zones
射嘴接触力 nozzle contact force
Injection射出
Cooling time 冷却时间
Holding time 锁模时间
Injection alarm time 射出警报时间
Injection start delay
Final cushion minimum value
Change-over to holding by value
Plasticizing end value
Hydrarlic change-over pressure holding
Screwvalue for change-over to holding
Change-over to holding by enable value
Hydraulic pressure in holding 锁模压力
Filling stage pressure limit
Injection speed 射出速度
Injection注射
Cooling time冷却时间
Holding time
Injection alarm time注射报警时间
Injection start delay注射开始延时
Final cushion minimum value最后段位置
Change-over to holding by value切换到锁模
agreePlasticizing end value预塑重终点
Hydrarlic change-over pressure holding切换到保压
打羽毛球的好处
Screwvalue for change-over to holding加料
Change-over to holding by enable value
Hydraulic pressure in holding锁模力
Filling stage pressure limit充模压力
Injection speed注射速度
Plasticizing delay预塑延时
1st suck-back speed储料一速度
1st suck-back pressure储料一压力
Screwrotation speed螺杆转速
Decompression value at end of injection注射终点
草书练字
Decompression value at end of plasticizing预塑终点
Mould closing关模
Mould clo force关模压力
Mould closing safety time.. 时间
Mould closing pressure.. 压力
1st closing safety stage pressure合模一段压力
1st mould closing speed ...成型速度
1st stage mould closing speed
1st stage mould closing 位置
High pressure start position高压锁模位置
Number of repeat mould closing movement..重复次数
Holding time 保压时间
Injection start delay 注射延迟
Injection注射
Cooling time冷却时间
Holding time保压时间
Injection alarm time注射报警时间
女宝宝名字Injection start delay注射开始延时(注射延时启动延时)
Final cushion minimum value最后段位置（最小余量）
Change-over to holding by value切换到锁模（保压由位置切换）
Plasticizing end value预塑重终点（熔胶终止）
疏雨
Hydrarlic change-over pressure holding切换到保压
Screwvalue for change-over to holding加料
Change-over to holding by enable value保压由位置切换
Hydraulic pressure in holding锁模力（保压）
Filling 填充
Injection alarm time 射胶时间肉烧饼
Injection start delay 延迟射胶
Final cushion minimum value 不知道这个是在哪个页面或项目下，如果是射胶那应该是：最小射胶终点（应该是品质项目设置的）
Change-over to holding by value不知道这个是在哪个页面或项目下，如果是射胶那应该是：最大射胶终点（应该是品质项目设置的）
Plasticizing end value终点位置
