NO | Code代码 | Type of Error | Possible Caus | Items to be Inspected | Action | |
10 | 0 | Motor Overheat/ Overload 电动机过热、过载 | 1. Motor thermal switch was clod. 2. Electronic thermal overload of either one of the following was activated: 150% for 60 c or longer, 200% for 26 c or longer, 300% for 10 c or longer. 3. No quence input power is supplied 1.电机热开关被闭合。 2.电子热过载中以下任一被激活: 150 %60 秒或更长时间、 26 秒或更长时间的 200%、 300%,持续 10 秒或更长时间。 3.没有序列输入供电。 | 1. Overload operation cycle. 2. Motor ambient temperature (must be lower the 40°C (104°F).) 3. Motor's cooling fan. 4. PWM carrier frequency 台风计划was incread. 5. Sequence input power. 1.超负荷运行周期。 2.电机的环境温度 (必须是低 40 ° C (104 ° F)。 3.电机冷却风扇。 4.PWM 载波频率增加。 5.序列输入功率。 | 1. Reduce operation load rate to 100% or less. 2. Cool down ambient temperature. 3. Repair motor's cooling fan. 4. Change the PWM carrier frequency to the standard value. 5. Provide appropriate quence input power. 1.减少操作负荷率为 100%或更少。2.环境温度下冷却。 3.修理电机的冷却风扇。 4.改变 PWM 载波频率的标准值。5.提供适当的序列输入的功率 | |
11 | 1 | Optional Card Failure | Optional card failure. | 1. See instruction manual of the optional card. | ||
12 | 2 | Power Elemen Failure 功率单元故障 | Overcurrent or overheat of power elements, or drop of drive power. 过流、过热 动力元件,或滴 驱动电源。 | 1. Setting of Drive and Motor Parameters. 2. Short of motor U, V, and W wiring. 3. Drive or power element failure. 4. Overload operation cycle. 1.设置的驱动器和电机的参数。2.缺的电机的 U、 V 和 W 接线。3.开车或电源单元出现故障。4.过载运行周期。 | 1. Check tting of parameters. 2. Check wiring and repair short. 3. Repair drive and power element. 4. Reduce operation load rate to 100% or less 1.请检查参数的设定。2.检查接线和补短。3.修复驱动器和电源的元素。4.减少操作负荷率为 100%或更少 | |
13 | 3 | Bus Overvoltage 母线过电压 | C bus input power exceeded 825 V. C总线输入功率超过825 V | 1. Input power exceeds specifications. 2. Retarding torque is beyond allowable range. 1。输入功率超过规范。2。制动转矩超出容许范围。 | 1. Verify that input power is appropriate. 2. Set lower current limit or lect appropriate resistance value for external regenerative resistor. 。验证输入功率是适当的。2。设置当前的下限或选择适合外部再生电阻器的电阻值。 | |
14 | 4 | Bus Overcurrent 过电流 | (This error code is not ud.) (这个不使用错误代码。) | |||
15 | 5 | Wrong Setting/Data Unconverted (1) | 1. Drop number is t to zero (0). 2. Set data is invalid. 3. Communication code is invalid (at communication with a host computer). 4. Motor is not for input voltage class. | 1. Drop number is out of tting range. 2. Set data or data combination is out of tting range. 3. Communication cable. 4. Power voltage and motor no-load voltage. | 1. Correct the drop number to the range of 1 to 99. 2. Correct t data. 3. Check drive grounding and connection of communication cable. 4. Correct tting of Motor Parameters. | |
16 | 6 | Motor Overspeed/ Speed Deviation Error | 1. Motor speed exceeded overspeed detection level. 2. Deviation of motor speed from speed reference exceeded speed deviation upper or lower limit. | 1. Improper overspeed detection level. 2. Overshoot at rapid acceleration or deceleration. 3. Material running out or cutting off during torque control operation. 4. Motor driven by load. | 1, 2. Adjust speed regulator gain and/or overspeed detection level. 3. Add speed clamping circuit. 4. Reduce load. | |
17 | C | Communication Error | Communication errors occurred more than allowable times. | 1. Improper baud rate. 2. Electrical noi. | 1. U proper baud rate (standard: 9600). 2. Install noi suppressors. | |
18 | r | Regulator Failure | 1. Power-up lf-diagnostics failure. 2. Option board failure was detected when optional card was installed. | 1. Control Board failure. 2. Option board failure. | 1. Replace the Control Board.草书书法字帖 2. Replace the option board. | |
19 | E | Pul Encoder (PG) Failure (2) | Incorrect A-pha/B-pha signal level of pul encoder (PG). | 1. Miswiring or disconnection of pul encoder (PG) wiring. 2. Pul encoder (PG) failure. 3. Input power failure. | 1. Correct wiring. 2. Replace the pul encoder (PG). 3. Repair or replace the power element. | |
20 | G | Ground Fault (3) | Ground fault was detected in wiring of motor U, V, and W. | 1. Insufficient insulation of motor wiring. 2. Insufficient insulation of motor. | 1. Correct wiring. 2. Repair motor. | |
21 | H | Drive Overheat (Converter Portion Failure) | 1. Converter portion heatsink overheat. 2. Overcurrent of converter portion (4) 3. Exceeding allowable charging time of DC bus. (4) | 1. Load status of the drive and ambinet temperature (should be 55°C (131°F) or lower). 2. Input power and short circuit of DC bus circuit. 3. Capacity of DC bus capacitors. | 1. Reduce operation load rate and cool down the ambient temperature. 2. Repair defective portions . 3. Review the organization of DC bus charging circuit. 4. Replace Control Board ACDC-41. | |
22 | L | AC Power Supply Failure | 1. When an external converter is ud, IP signal from the converter has been kept for longer than the tting of Application Parameter "Inst. Pwr. Dip Detect Time". 2. DC bus voltage is lower than 399 V. | 1. Power loss or circuit breaker trip. 2. Converter portion was defective. | 1. Check input power. 2. Repair the converter portion. | |
23 | P | Control Power Failure | (This error code is not ud.) | |||
24 | U | Bus Low Voltage (5) | DC bus voltage is lower than 371 V. | 1. Input power is lower than the specifications. 2. Short of DC bus input power. 3. Fault of internal power elements. 4. Fault of converter portion. | 1. Provide proper input power according to specifications. 2. Check an external regenerative resistor. 3. Repair the drive. 4. Repair the converter portion. | |
25 | 一个人的空间d | Driver Power Supply Failure | (This error code is not ud.) | |||
(1)While parameters are transmitted to the drive, this error code lights on, but when the parameters can be t normally and transmission is completed normally, this error code will be turned OFF. (2)This error will be cleared when the drive enters in the test operation mode. (3)This error code is effective only when an optional residual current transformer is ud. (4)This is not applicable to Model UVZC3401G to UVZC3407G. (5)This error code is not displayed when the drive is ud with a common bus input power. When an external converter is ud, the bus low voltage error of the inverter will be cleared if the inverter does not receive the RDY signal from the converter | ||||||
26 | 7 | Motor Overheat Alarm | Motor temperature measured by thermistor exceeded the t value of overheat temperature. | 1. Overload operation cycle. 2. Motor ambient temperature (must be lower the 40°C (104°F).) 3. Motor's cooling fan | 1. Reduce load rate of operation to 100% or less. 2. Cool down ambient temperature. 3. Repair motor's cooling fan. 4. Correct the t value of overheat temperature. | |
27 | 8 | During Torque Limiting (displayed only during speed control) | Torque current reference is limited by FWD/REV torque limit. | 1. Load is too large. 2. Accel/decel time is too short. 3. Set value of torque limit is too small. | 1. Reduce load. 2. Set longer accel/decel time. 3. Set larger torque limit. | |
28 | 9 | Torque Control Failure (displayed only during torque control) | Speed is clamped in torque control operation with speed clamping circuit. | Load status becomes less than torque current reference. | Set load status within control range. | |
29 | Line Overspeed | Motor Speed exceeded detection level 1 and 2 for alarm. | Adequacy of the speed detection levels 1 and 2 for alarm. | Speed down the motor. | ||
30 | A | Line Overspeed | Motor Speed exceeded detection level 1 and 2 for alarm. | Adequacy of the speed detection levels 1 and 2 for alarm. | Speed down the motor. | |
31 | F | Motor Temperature Sensor Failure | Thermistor resistance for motor is out of allowable range. | 1. Short, disconnection, contact failure of wiring. 2. Thermistor failure. 3. Motor temperature is lower than –5°C (23°F). 4. Motor temperature is higher than 150°C (302°F). | 1. Check wiring. 2. Replace the thermistor. 3. Operate the motor in warm air. | |
J | EEPROM 桂花树怎么画Write Error | Error of wiring to EEPROM occurred. | 1. Writing to EEPROM exceeded hundred thousand times. 2. Element failure. | 1, 2. Replace the Control Board. | ||
32 | b | During Ba Blocking (1) (3) | Ba block is activated at power-up. | Power was turned ON while RUN signal was ON. | Turn RUN signal ON after power-up. | |
33 | c | Communication Error | Communication error occurred or communication watchdog error was detected. | 1. Improper baud rate. 2. Electrical noi. | 1. Correct baud rate (standard: 9600). 2. Install noi suppressors. | |
34 | h | Set Data Ignored | Set data is invalid. | 1. Set data is beyond tting range. 2. Set data combination is beyond tting range. | 1, 2. Correct t data. | |
35 | AC Power Supply Instantaneous Power Failure Overlo | 1. When an external converter is ud, the IP 为什么不可以signal from the converter was received. 2. DC bus voltage is lower than 399 V | 1. Instantaneous power loss. 2. Input power voltage is out of the specifications, or power capacity is too small. | 1. Check input power. 2. Correct power capacity. | ||
36 | O | Overload Alarm | Overload operation continued for over 80% of allowable overload time. | 1. Overload operation cycle. 2. Incorrect t value. 3. Pha loss of U, V, W output. 4. PWM carrier frequency was incread. | 1. Reduce load rate to 100% or less. 2. Correct Drive and Motor Parameters. 3. Correct wiring. Repair the drive if necessary. 4. Change the PWM carrier frequency to the standard value. | |
37 | n | Converter Portion Failure (1) (2) 转换器部分失败(1)(2 | Fault signal of converter portion was detected. 检测故障信号转换器的部分 | 1. Input power of converter portion is OFF or below the specifications. 2. Converter portion failure. 1。输入功率转换器部分或低于规范。2。转换器部分失败。 | 1. Establish input power. 2. Repair the converter portion. 1。建立输入功率。2。修复转换器部分。 | |
38 | y | Option Board Fault | Communication with option board was disconnected due to option board failure. | Option board failure. | See instruction manual of the option board. | |
39 | - | Forced Stop (1) (4) | Forced stop command was received through communication. | Check the status of the command source. | Take adequate action depending on the status of the command source. | |
(1)No operation is possible while this code is displayed. (2)No operation is possible until converter portion becomes ready for operation. (3)No operation is possible while this code is displayed. This code will be cleared by turning OFF the RUN signal of external quence input. (4)No operation is possible while this code is displayed. This code will be cleared by turning OFF the RUN signal of external quence input and pressing the RESET switch. | ||||||
40 41 42 43 44 45 手工作品制作方法 | 0 1 2 3 4 6 | Processor Internal Error | Self-diagnostics Failure at Power-up | Control Board failure | Replace the Control Board | |
形容桂花香的优美句子 46 | 7 | Mismatching of revisions | 勇敢 Mismatching of revisions between main-firmware and sub-firmware. Mismatching of revisions between sub-firmware and option board. | Control Board failure. Option board failure. | Replace the Control Board. Replace option board. | |
本文发布于:2023-05-17 09:28:38,感谢您对本站的认可!
本文链接:https://www.wtabcd.cn/fanwen/fan/89/907541.html
版权声明:本站内容均来自互联网,仅供演示用,请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系,我们将在24小时内删除。
留言与评论(共有 0 条评论) |