Corning® ClearCurve® ZBL Optical Fiber
Product Information
Bend Performance and Compatibility
Corning® ClearCurve® ZBL Optical Fiber delivers the best macrobending performance in the industry while maintaining compatibility with current optical fibers, equipment, practices and procedures. This full-spectrum single-mode optical fiber when subjected to smaller radii bends experiences virtually no signal loss. ClearCurve fiber exceeds the most stringent bend performance requirements of ITU-T Recommendations G.657.B3, while remaining fully compliant with ITU-T Recommendation G.652.D and the installed ba of Corning® SMF-28e® and SMF-28e+® fiber. Now network planners and designers can design optical fiber into much more challenging installations and environments, and cable designers can offer optical cables with unmatched ruggedness for easier installation and handling.
再寄小读者
Maximum Attenuation Wavelength (nm)
Maximum Value (dB/km)*
13100.33 – 0.351383**0.31 – 0.3514900.21 – 0.2415500.19 – 0.201625榴莲有核吗
0.21 – 0.23
Attenuation vs. Wavelength Range (nm)Ref. λ (nm)
Max. α Difference
(dB/km)
沈小明
1285 – 133013100.031525 – 1575
1550
0.02
Optical Specifications
PI 1464 | Issued : July 2010 Superdes: October 2009 | TL 9000/ISO 9001 Registered
* M aximum specified attenuation value available within the stated ranges.
** A ttenuation values at this wavelength reprent post-hydrogen aging performance.孕妇能吃毛蛋吗
Alternate attenuation offerings available upon request.
The attenuation in a given wavelength range does not exceed the attenuation of the reference wavelength (λ) by more than the value of α.
* T he induced attenuation due to fiber wrapped around a mandrel of a specified diameter.
Zero Dispersion Wavelength (λ0): 1304 nm ≤λ0≤1324 nm
Zero Dispersion Slope (S0): ≤0.092 ps/(nm2*km)
* C omplies with IEC 60794-3: 2001, Section 5.5, Method 1, (m = 20,
Q = 0.01%), September 2001.
The link design value is a term ud to describe the PMD of concatenated lengths of fiber (also known as PMD Q). This value reprents a statistical upper limit for total link PMD. Individual PMD values may change when fiber is cabled. Corning’s fiber specification supports emerging network design requirements for high-data-rate systems operating at 10 Gb/s or higher.
Corning Incorporated
One Riverfront Plaza Corning, NY 14831 U.S.A. Ph: 607-248-2000 Email: /opticalfiber Corning and ClearCurve are registered trademarks of Corning Incorporated, Corning, NY.
© 2010 Corning Incorporated
拿铁英语
Macrobend Loss
Mandrel Radius (mm)Number of
Turns
Wavelength
(nm)
Induced
Attenuation*
(dB)
511550≤0.10 511625≤0.30
Point Discontinuity
Wavelength (nm)Point Discontinuity (dB) 1310≤0.05
1550≤0.05 Mode-Field Diameter
Wavelength (nm)MFD (μm)
13108.6 ± 0.4
15509.65 ± 0.5 Dispersion
Wavelength (nm)Dispersion Value
[ps/(nm*km)]
1550≤18Coating Geometry
Coating Diameter245 ± 5 μm Coating-Cladding Concentricity<12 μm
Polarization Mode Dispersion (PMD)
Value (ps/√km) PMD Link Design Value≤0.06* Maximum Individual Fiber≤0.2Glass Geometry
Fiber Curl≥4.0 m radius of curvature Cladding Diameter125.0 ± 0.7 μm
对领导班子的意见和建议Core-Clad Concentricity≤0.5 μm
Cladding Non-Circularity≤0.7%
Environmental
Test Test Condition
Induced
Attenuation
1310 nm, 1550 nm
& 1625 nm
(dB/km) Temperature
Dependence-60°C to +85°C*≤0.05
Temperature
Humidity Cycling
-10°C to +85°C*
up to 98% RH≤0.05 Water Immersion23°C ± 2°C≤0.05
狗腿是什么意思Heat Aging85°C ± 2°C*≤0.05
踏踢
Damp Heat85°C* at 85%
RH≤0.05
Cable Cutoff Wavelength(λccf)λccf≤1260 nm Dimensional Specifications Environmental Specifications
Mechanical Specifications
Proof Test
The entire fiber length is subjected to a tensile stress ≥100 kpsi (0.7 GPa)*.
* Higher proof test levels available.
Length
Fiber lengths available up to 50.4* km/spool.
* Longer spliced lengths available.
* Reference temperature = +23°C
Operating Temperature Range: -60°C to + 85°C
Optical Specifications (cont’d)
