最全的压铸模具相关英语注释超值压铸英语
A 安装尺⼨install dimension
凹模固定板retainer plate
凹模female die, female mold, negative mold
B 备件spare parts
变质modification
变质剂modification agent
扒渣slagging-off
保温炉holding furnace
保压压⼒dwell pressure
表⾯缺陷surface defect
C 淬⽕硬度quenching hardness
抽芯core
侧⾯抽芯side core
抽芯油缸core oil cylinder
插拔式结构plug
抽芯机构core puller
抽芯油缸⽀架bracket of cylinder
粗糙度roughness/degree 铸件表⾯粗糙度surface roughness
擦伤galling
尺⼨公差dimension tolerance of casting
除⽓degassing
吹⽓净化blow purifying
除⽓剂degassing flux
出渣de-slagging
出渣⼝slag hole
沉渣sludge
出炉⼝tap hole
菜花头Cauli-flowering
超声波检验ultrasonic test
重熔re-melting
D 端盖cover
动模垫块spacer parallel
锻钢forged steel
氮化处理nitriding treatment
断裂fracture
塑性断裂plastic fracture
导柱guide pillar
导套guide sleeve
导向板guide plate
导向件guide part
动型moving die/ejector die/movable mould
动模座板moving clamp plate/bottom clamping plate 定模座板fixed clamp plate/top plate 定型fixed die/cover die
定模套版bolster/fixed die
顶杆ejector pin
顶出结构ejector mechanism
顶出ejector
吊装孔lifting eye
吊环lifting ring
镀钛处理titanium plating treatment
多⾁缺陷metallic projection
电⽕花electric spark
打磨grinding
F 分流锥divider/blast cone
分型⾯mold parting/parting face/mold joint
附页attachment/appendix
复位杆ret bar(rod)
附件故障accessory
覆盖剂covering flux
废⾦属料scrap
浮渣cinder
反射炉reverberatory furnace
废品reject
飞边joint flash
仿真simulation
G 规格specification/standard 数值孔径numerical aperture (N.A)
固定段gment
坩埚crucible
坩埚炉crucible furnace
感应电炉electric induction furnace
沟槽blind scab
硅Silicon
H 滑块sliding block
滑块部件moving parts
滑块退让return/move back
焊补welding-on
横浇道runner
合模die locking
横流道runner
回炉料foundry returns
合型mold asmbling/closing/die locking
合型⼒die locking force
化学成分不合格chemical consistence analysis J 浇⼝套sprue bush
浇排道系统pouring system
浇不⾜misrun
浇注pouring
浇注断裂interrupted pour
浇道⽐gating ratio
浇包ladle
精整dressing and finishing
精度accuracy
接⼝connector
击伤shot damage
⾦相组织metallographic structure
⾦属残液heel
⾦相检验metallographic test
⾦属型涂料die coating/coating for metal mold 加压速度rate of pressure increasing
间隙clearance
精炼refining
精炼剂refining flux
精密铸造precision casting
静置holding/stewing
渗透impregnation
集渣装置dirt traps
夹杂类缺陷inclusion defects
夹渣entrapped slag/slag inclusion
夹具tool fixtures
K 壳体housing
开炉blowing in
孔洞缺陷cavity
库存inventory
L 冷却cooling
冷却⽔管cooling water pipe
冷却耐压管cooling pressure pipe
冷却⽔管⽤密封圈O-ring/aling ring/gasket ring
冷室卧式压铸机horizontal (cold chamber) die casting machine 冷却系统cooling system
冷却⽔接⼝cooling water connector
冷裂cold crack
冷隔cold lap
铝Aluminum
裂纹crack
拉伤caught casting
拉杆孔draw bar
螺纹screw/thread
螺纹结构screw structure
螺纹公称直径(直径diameter)
公称尺⼨(名义尺⼨) specified size/nominal dimension
漏油leakage of oil
棱边倒⾓edge
炉料charge
炉衬furnace lining
炉⽓分析flue gas analysis
炉前分析on-the-spot sample analysis
流痕bloom/flow line
⼒学性能不合格physical-mechanical characteristic abnormal
M ⽑坯rough/blank
⽑坯铸件rough casting
⽑刺veining/burr
模芯core
模框frame
模槽mold channel
模套cha/bolster/frame
模具钢die steel
模具图纸mold drawing
内浇⼝in-gate
冒⼝rir/feeder head
冒⼝浇注系统feeder head gating system
镁Magnesium
锰Mangane
密闭耐压系统tightness test
N 内浇道in-gate
镍Nickle
P 配油盘pressure plate
排⽓块exhaust block
排⽓槽air vent
排⽓孔vent/venting channel
排⽓塞venting plug
配合套圆形:fitting sleeve ⽅型: fitting ca 跑铝aluminum slop out of mold 喷射冶⾦injecting metallurgy
喷丸清理shot blasting cleaning
抛丸清理wheel blasting cleaning
偏析gregation
破坏性实验destructive test
Q 取件机extractor
去除浇冒⼝de-gating
清铲chipping
缺陷铸件defecting casting
⽓孔blowhole/gas cavity/pinhole/porosity ⽓孔缩blowhole shrinkage
去⽑刺de-burring
去除氧化⽪de-scaling
