Safety Data Sheet
Roto-Xtend Duty Fluid
1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND COMPANY/UNDERTAKING
Product Code 0017 5201 20 Infosafe No. ACN5C GB/eng/C Issued Date
11/07/2011 Product Type/U Compressor oil.
Supplier
Telephone Numbers Emergency Tel. +32 3 870 21 11
Telephone/Fax Number
Plea contact the nearest Atlas Copco Sales Company or for urgent matters the Medical Service of Atlas Copco Airpower in Belgium (+32 3 870 21 05) Atlas Copco Airpower nv Boomsteenweg 957 B-2610 Wilrijk BELGIUM
2. HAZARDS IDENTIFICATION
EC Classification
Not classified as Dangerous under EC criteria.
Human Health Hazards
No specific hazards under normal u conditions. Prolonged or repeated exposure may give ri to dermatitis. Ud oil may contain harmful impurities.
Safety Hazards
Not classified as flammable, but will burn.
Environmental Hazards
Not classified as dangerous for the environment.
3. COMPOSITION/INFORMATION ON INGREDIENTS Preparation Description
Blend of polyolefins and additives.
Name
CAS EINECS Proportion Hazard R Phra Alkaryl amine
68411-46-1 270-128-1 1-5 % R52/53
Dialkyl thiophosphate ester
268567-32-4
0.1-0.5 %
Xi
R41, R43, R52/53
Other Information
See Section 16 'Other Information' for full text of each relevant Risk Phra.
4. FIRST AID MEASURES
Symptoms and Effects
Not expected to give ri to an acute hazard under normal conditions of u. May cau an allergic skin
reaction in nsitive individuals.
Inhalation
中效消毒剂
In the unlikely event of dizziness or naua, remove casualty to fresh air. If symptoms persist, obtain medical attention.
Skin
Remove contaminated clothing and wash affected skin with soap and water. If persistent irritation occurs, obtain medical attention. When using high pressure equipment, injection of product under the skin can occur. If high pressure injuries occur, the casualty should be nt immediately to a hospital. Do not wait for symptoms to develop.
Eye
Flush eye with copious quantities of water. If persistent irritation occurs, obtain medical attention.
Ingestion
Wash out mouth with water and obtain medical attention. Do not induce vomiting.
Advice to Doctor
Treat symptomatically. Aspiration into the lungs may result in chemical pneumonitis. Dermatitis may result from prolonged or repeated exposure. High pressure injection injuries require prompt surgical intervention and possibly steroid therapy, to minimi tissue damage and loss of function.
Becau entry wounds are small and may not reflect the riousness of the underlying damage, surgical exploration to determine the extent of involvement may be necessary. Emesis of lubricants is not usually necessary, unless a large amount has been ingested, or some other compound has been dissolved in the product. If this is indicated, for example, when there is rapid ont of central nervous system depression from large ingested volume - gastric lavage under controlled hospital conditions, with full protection of the airway is required. Supportive care may include oxygen, arterial
blood gas monitoring, respiratory support, and, if aspiration has occurred, treatment with corticosteriods and antibiotics. Seizures should be controlled with Diazepam, or appropriate equivalent drug.
家长感言怎么写5. FIRE FIGHTING MEASURES
Specific Hazards
Combustion is likely to give ri to a complex mixture of airborne solid and liquid particulates and gas, including carbon monoxide and unidentified organic and inorganic compounds.
Extinguishing Media
Foam and dry chemical powder. Carbon dioxide, sand or earth may be ud for small fires only.
Unsuitable Extinguishing Media
Water in jet. U of halon extinguishers should be avoided for environmental reasons.月光光心慌慌11
Protective Equipment
Proper protective equipment including breathing apparatus must be worn when approaching a fire in a confined space.
6. ACCIDENTAL RELEASE MEASURES
Personal Precautions
Avoid contact with skin and eyes. Wear PVC, Neoprene or nitrile rubber gloves. Wear rubber knee length safety boots and PVC Jacket and Trours. Wear safety glass or full face shield if splashes are likely to occur. Environmental Precautions
华山海拔多少米Prevent from spreading or entering into drains, ditches or rivers by using sand, earth, or other appropriate barriers. Inform local authorities if this cannot be prevented.
恒洁卫浴在十大名牌排名第几Clean-up Methods - Small Spillages
Absorb liquid with sand or earth. Sweep up and remove to a suitable, clearly marked container for disposal in accordance with local regulations.
Clean-up Methods - Large Spillages
Prevent from spreading by making a barrier with sand, earth or other containment material. Reclaim liquid
directly or in an absorbent. Dispo of as for small spills.
7. HANDLING AND STORAGE
Handling
U local exhaust ventilation if there is risk of inhalation of vapours, mists or aerosols. Avoid prolonged or repeated contact with skin. When handling product in drums, safety footwear should be worn and proper handling equipment should be ud. Prevent spillages. Cloth, paper and other materials that are ud to absorb spills prent a fire hazard. Avoid their accumulation by disposing of them safely and immediately. In addition to any specific recommendations given for controls of risks to health, safety and the environment, an asssment of risks must be made to help determine controls appropriate to local circumstances. Exposure to this product should be reduced as low as reasonably practicable. Reference should be made to the Health and Safety Executive's publication '
COSHH Esntials'.
Storage
Keep in a cool, dry, well-ventilated place. U properly labelled and cloable containers. Avoid direct sunlight, heat sources, and strong oxidizing agents.
Storage Temperatures
0ºC Minimum. 50ºC Maximum.
Recommended Materials
For containers or container linings, u mild steel or high density polyethylene.
Unsuitable Materials
For containers or container linings, avoid PVC.
Other Information
Polyethylene containers should not be expod to high temperatures becau of possible risk of distortion.
8. EXPOSURE CONTROLS, PERSONAL PROTECTION
Exposure Limits
No Exposure Limit Established
Exposure Controls
The u of personal protective equipment is only one aspect of an integrated approach to the Control Of Substances Hazardous to Health.
The management of Health and Safety at Work Regulations 1992 require employers to identify and evaluate the risks to health and to implement appropriate measures to eliminate or minimi tho risks. The choice of personal protective equipment is highly dependent upon local conditions, e.g. exposure to other chemical substances and micro-organisms, thermal hazards (protection from extremes of cold and heat), electrical hazards, mechanical hazards and appropriate degree of manual dexterity required to undertake an activity. Whilst the content of this ction may inform the c播音主持专业就业前景
hoice of personal protective equipment ud, the limitations of any information which can be provided must be fully understood, e.g. personal protective equipment chon to protect employees from occasional splashes maybe entirely inadequate for activities involving partial or complete immersion.If the levels of oil mist or vapour in air are likely to exceed the occupational exposure standards then consideration should be given to the u of local exhaust ventilation to reduce personal exposure.
The choice of personal protective equipment should only be undertaken in the light of a full risk asssment by a suitably qualified competent person ( e.g. a professionally qualified occupational hygienist).
Effective protection is only achieved by correctly fitting and well maintained equipment and employers should ensure that appropriate training is given. All personal protective equipment should be regularly inspected and replaced if defective.
Respiratory Protection
Care should be taken to keep exposures below applicable occupational exposure limits. If this cannot be achieved, u of a respirator fitted with an organic vapour cartridge combined with a partic
ulate pre-filter should be considered. Half masks (EN 149) or valved half masks (EN 405) in combination with type A2 (EN 141) and P2/3 (EN 143) pre-filters maybe considered.
Hand Protection
Chemical protective gloves are made from a wide range of materials, but there is no single glove material ( or combination of materials) which gives unlimited resistance to any individual or combination of substances or preparations. The extent of the breakthrough time will be affected by a combination of factors which include permeation, penetration, degradation, u pattern ( full immersion, occasional contacts) and how the glove is stored when not in u.
Theoretical maximum levels of protection are ldom achieved in practice and the actual level of protection can be difficult to asss. Effective breakthrough time should be ud with care and a margin of safety should be applied. HSE guidance on protective gloves recommends a 75% safety factor to be applied to any figures obtained in a laboratory test. Nitrile gloves may offer relatively long breakthrough times and slow permeation rates. Test data, e.g breakthrough data obtained through test standard EN374-3:1994 are available from reputable equipment suppliers.
Personal hygiene is a key element of effective hand care. Gloves must only be worn on clean hands. After using gloves, hands should be washed and dried thoroughly. A non perfumed moisturir should be applied.
Eye Protection
Goggles conforming to a minimum standard of EN 166 345B should be considered if there is a possibility of eye contact with the product through splashing. Higher rated eye protection must be considered for highly hazardous operations or work areas. For example, employees involved in metalworking operations such as chipping, grinding or cutting may require additional protection to avert injury from fast moving particles or broken tools.
Body Protection
Minimi all forms of skin contact. Overalls and shoes with oil resistant soles should be worn. Launder overalls and undergarments regularly.
Environmental Exposure Controls
Minimi relea to the environment. An environmental asssment must be made to ensure compli
ance with local environmental legislation.
9. PHYSICAL AND CHEMICAL PROPERTIES
Colour Straw. Pale yellow.
Physical State Liquid at ambient temperature.
Odour Characteristic.
pH Value Data not available.
Vapour Pressure Expected to be less than 0.5 Pa at 20°C.
Initial Boiling Point Data not available.
Solubility in Water Negligible.
Density circa 842 kg/m3 at 15ºC.
Flash Point >230ºC (COC).
Flammable Limits - Upper 10%(V/V) (typical).
Flammable Limits - Lower 1%(V/V) (typical).
Auto-Ignition Temperature Expected to be above 320ºC.
Kinematic Viscosity 46 mm2/s at 40ºC.
Evaporation Rate Data not available.
Vapour Density (Air=1) Greater than 1.
Partition co-efficient, n-octanol/water Log Pow expected to be greater than 6.
Pour Point circa -60ºC.
10. STABILITY AND REACTIVITY
Stability
Stable.
Conditions to Avoid
Extremes of temperature and direct sunlight.
Materials to Avoid
Strong oxidizing agents.
Hazardous Decomposition Products
Hazardous decomposition products are not expected to form during normal storage.
11. TOXICOLOGICAL INFORMATION
Basis for Asssment
Toxicological data have not been determined specifically for this product. Information given is bad on a knowledge of the components and the toxicology of similar products.
Acute Toxicity - Oral
LD50 expected to be > 2000 mg/kg.
Acute Toxicity - Dermal
LD50 expected to be > 2000 mg/kg.
危险化学品安全管理制度
Acute Toxicity - Inhalation
终身无憾Not considered to be an inhalation hazard under normal conditions of u.
Eye Irritation
Expected to be slightly irritating.
Skin Irritation
Expected to be slightly irritating.
Respiratory Irritation
If mists are inhaled, slight irritation of the respiratory tract may occur.
Skin Sensitisation
Not expected to be a skin nsitizer.
Carcinogenicity
Components are not known to be associated with carcinogenic effects.
Mutagenicity
Not considered to be a mutagenic hazard.
Reproductive Toxicity
Not considered to be toxic to reproduction.
Other Information
Prolonged and/or repeated contact with this product can result in defatting of the skin, particularly at
elevated temperatures. This can lead to irritation and possibly dermatitis, especially under conditions of poor personal hygiene. Skin contact should be minimid. High pressure injection of product into the skin may lead to local necrosis if the product is not surgically removed. Ud oils may contain harmful impurities that have accumulated during u. The concentration of such impurities will depend on u and they may prent risks to health and the environment on disposal. ALL ud oil should be handled with caution and skin contact avoided as far as possible.
12. ECOLOGICAL INFORMATION
Basis for Asssment
Ecotoxicological data have not been determined specifically for this product. Information given is bad on a knowledge of the components and the ecotoxicology of similar products.
Mobility
Liquid under most environmental conditions. Floats on water. If it enters soil, it will adsorb to soil particles and will not be mobile.
Persistence / Degradability
Not expected to be readily biodegradable. Major constituents are expected to be inherently biodegradable, but the product contains components that may persist in the environment.
