模具名称中英文对照

更新时间:2023-07-29 22:03:22 阅读: 评论:0

中文      =  英文
顶针  =  E.P.
有托顶针  = Stepped E.P.
扁顶针  = Rectangular E.P.
司筒/司筒针  = E.P.Sleeve
直身导边  = Straight Leader Pin
有托导边  = Shoulder Leader Pin
直身杯司  = Straight Bushing
有托杯司  = Shoulder Bushing
方定位块  = Position  Block Set
定位锥  = Taper Pin Set
尼龙塞  = Parting Lock
中托司套  = Ejector Lead Bushing
中托导柱  = Ejector Leader Pin
脱水口螺丝组  = Puller Bolt Set
限位螺丝  = Stopper Bolt
限位钉  = Positioning Pin
管位块  = Slotter Key
弹簧  = Spring
螺钉  = Screw
限位块  = Distance Spacer
无头螺钉  = Screw Plug
平头螺钉  = Socket Head Cap Screw
波子螺丝  = Ball Plunger
定位螺钉  = Positioning Screw Plug
胶圈  = O ring
喉塞  = Taper Screw Plug
法兰  = Locating Ring
唧嘴  = Sprue Bushing
截流塞  = Cooling Circuit Plug
上固定板  = Top Clamping Plate
脱料板  = Runner Stripper Plate
上模板  = Cavity Plate
推板  = Stripper Plate
下模板  = Core Plate
支承板  = Support Plate
间隔板  = Spacer Block
顶针板1  = Ejector Plate 1
顶针板2  = Ejector Plate 2
下固定板  = Bottom Clamping Plate
回针  = Return Pin
拉杆  = Support Pin
拉杆定位介子  = Support Pin Spacer
齿轮  = Gear
丝杆  = Screw
轴承  = Bearing
油缸  = Oil Cylinder
气缸  = Air Cylinder
间隔圈  = Spacer Ring
垃圾钉  = Slopper Ring
撑头  = Support Pillar
行位开关组  = Detection Switch Set
站脚  = Distance Spacer
斜顶  = ANGULAR
扣机(尼龙拉勾)  = nylon latch lock
模胚(架)  = mold ba
上模  = Cavity
上模镶件  = Cavity Inrt
上模镶针  = Inlay Cavity Pin
潜水镶套  = Pin Point Gate Bushing
死寂电影流道衬板  = Runner Plate
水口扣针  = Runer Lock Pin
行位  = Slider
趟过去
行位开关组  = Detection Switch Set
站脚  = Distance Spacer
行位导向键  = Slider Certer Rail
行位镶件  = Slider Inrt
斜边  = Angular Pin
方斜边  = Angular Cam
铲鸡  = Locking Block
行位压板  = Slider Guide Rail那些未完成的>端口速率
隔热板  = Insulation Sheet
小鱼的画法压板(其他类)  = Holding Plate
楔块  = Spacer Wedge
销钉  = Dowel Pin
下模  = Core
下模镶件  = Core Inrt
支承板  = Support Plate
间隔板  = Spacer Block
下模镶针  = Core Pin
撑头  = Support Pillar
流道衬板  = Runner Plate
水口扣针  = Runer Lock Pin
拉板  = Tension Link
拉板介子  = Tension Link Retainer
行位垫块  = Slide Plate
斜边压块  = Holding Plate For A.P.
斜顶滑座  = Slide Unit For Loo Core
冷胶套  = Sprue Lock Bushing
运水镶件  = Inrt For Cooling
等高螺丝  = Stopper Bolt
入水  = gate
进入位  = gate location
水口形式  = gate type
大水口  = edge gate
细水口  = pin-point gate
水口大小  = gate size
转水口  = switching runner/gate
唧嘴口直径  = sprue diameter
流道  = runner
热流道  = hot runner/hot
manifold
热嘴冷流道  = hot sprue/cold runner
唧嘴直流  = direct sprue gate正义之战
圆形流道  = round/full/half runner
流道电脑分析  = mold flow analysis
流道平衡  = runner balance
热嘴  = hot sprue
热流道板  = hot manifold
发热管  = cartridge heater
探针  = thermocouples
插头  = connector plug
插座  = connector socket
密封/封料  = al
运水  = water line/line lpug
喉管  = tube
塑胶管  = plastic tube
快速接头  = jiffy quick connector plug/socker
模具零件  = mold components
三板模  = 3-plate mold
二板模  = 2-plate mold
边钉/导边  = leader pin/guide pin
迎老爷
边司/导套  = bushing/guide bushing
中托司  = shoulder guide bushing
中托边  = guide pin
中托导柱  = Ejector Leader Pin
脱水口螺丝组  = Puller Bolt Set
限位螺丝  = Stopper Bolt
顶针板  = ejector retainner plate
限位钉  = Positioning Pin
眼神描写托板  = support plate
螺丝  = screw
管钉  = dowel pin
开模槽  = ply bar scot
内模管位  = core/cavity inter-lock
压座/斜鸡  = wedge
耐磨板/油板  = wedge wear plate
压条  = plate
定位圈  = locating ring
琐扣  = latch
扣鸡  = parting lock t
推杆  = push bar
栓打螺丝  = S.H.S.B
顶板  = eracuretun
活动臂  = lever arm
分流锥  = spure sperader
水口司  = bush
隔片  = buffle
弹弓柱  = spring rod
弹弓  = die spring
镶针  = pin
销子  = dowel pin
波子弹弓  = ball catch
复位键\提前回杆  = early return bar
气阀  = valves
斜导边  = angle pin
术语  = terms
承压平面平衡  = parting surface support balance
模排气  = parting line venting
回针碰料位  = return pin and cavity interference
模总高超出啤机规格 = mold ba shut hight
顶针碰运水  = water line interferes withejector pin
料位出上/下模  = part from cavith (core) side
模胚原身出料位  = cavity direct cut on A-plate,core direct cut on B-plate.
不准用镶件  = Do not u (core/cavity) inrt
用铍铜做镶件  = u beryllium copper inrt
初步(正式)模图设计  = preliinary (final) mold design
弹弓压缩量  = spring compresd length
稳定性好  = good stability,stable
强度不够  = insufficient rigidity
均匀冷却  = even cooling
扣模  = sticking
热膨胀  = thero expansion
公差  = tolorance
铜公(电极)  = copper electrode

本文发布于:2023-07-29 22:03:22,感谢您对本站的认可!

本文链接:https://www.wtabcd.cn/fanwen/fan/89/1101254.html

版权声明:本站内容均来自互联网,仅供演示用,请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系,我们将在24小时内删除。

标签:行位   螺丝   流道   螺钉   镶件
相关文章
留言与评论(共有 0 条评论)
   
验证码:
推荐文章
排行榜
Copyright ©2019-2022 Comsenz Inc.Powered by © 专利检索| 网站地图