stripper plate | 推件板 | |
stripper ring. strpper disk | 推件环/盘 | |
runner stripper plate | 推流道板 | |
stripper distance | 脱模距 | |
动模 | movable mould moving half | |
定模座板 | fixed clamp plate, top clamping plate. top plate | |
动模座板 | moving clamp plate. bottom clamping plate. bottom plate | |
上模座板 | upper clamping plate | |
下模座板 | lower clamping plate | |
凹模固定板 | cavity-retainer plate | |
型芯固定板 | core-retainer plate | |
凸模固定板 | punch-retainer plate | |
模套 | cha. bolster. frame | |
支承板 | backing plate. supprr plate | |
垫块 | spacer parallel | |
支架 | ejector housing. mould ba leg | |
cavity (of a mould) | 型腔 | |
impression cavity block. cavity plate | 凹模 | |
cavity splits 飘香鸡 | 凹模拼块 | |
thread ring. threaded cavity | 螺纹型环 | |
cavity-retainer plate | 凹模固定板 | |
internal mould pressure. cavity pressure | 模内压力 | |
runner plate | 流道板 | |
warm runner plate | 温流道板 | |
impression cavity block. cavity plate | 凹模 | |
fixed clamp plate, top clamping plate. top plate | 定模座板 | |
moving clamp plate. bottom clamping plate. bottom plate | 动模座板 | |
upper clamping plate | 上模座板 | |
lower clamping plate | 下模座板 | |
cavity-retainer plate | 凹模固定板 | |
core-retainer plate | 型芯固定板 | |
punch-retainer plate | 凸模固定板 | |
backing plate. supprr plate 搜狗浏览器网页 | 支承板 | |
mould plate | 模板 | |
finger guide plate | 斜槽导板 | |
ejector plate return pin. push-back pin | 复位杆 | |
puller plate. limit plate | 定矩拉板 | |
stripper plate | 饱经风霜推件板 | |
ejector retainer plate | 推杆固定板 | |
dejection plate. ejector plate | 推板 | |
runner stripper plate | 推流道板 | |
heating plate | 加热板 | |
director guide fush. ejector bushing | 推板导套 | |
ejector plate return pin. push-back pin | 报捷复位杆 | |
ejector pin | 推出零件/推杆 | |
ejector pin with cylindrical head | 圆柱头推杆 | |
shouldered ejector pin | 带肩推杆 | |
flat ejector pin | 扁推杆 | 马尾巴|
ejector sleeve | 推管 | |
ejector pad | 推块 | |
ejector retainer plate | 推杆固定板 | |
dejection plate. ejector plate | 推板 | |
ejector tie rod | 连接推杆 | |
side core. slide core | 侧型芯 | |
slide. cam slide | 滑块 | |
slide. core-slide | 侧型芯滑块 | |
slide glide strip | 滑块导板 | |
core splits | 型芯拼块 | |
core splits | 型芯 | |
side core. slide core | 侧型芯 | |
thread plug, threaded core | 螺纹型芯 | |
core-retainer plate | 型芯固定板 | |
slide. core-slide | 侧型芯滑块 | |
core-pulling force | 油芯力 | |
core-pulling distance | 抽芯距 | |
gating inrt | 浇口镶块 | |
mould inrt | 镶件 | |
movable inrt. loo detail | 活动镶件 | |
sprue bush sprue busing | 浇口套 | |
sprue puller | 拉料杆 | |
sprue puller, z-shaper | 钩形拉料杆 | |
sprue puller, ball headed | 球头拉料杆 | |
sprue puller. conical headed | 圆锥头拉料杆 | |
insulated runner mould | 绝热流道模 | |
warm runner mould | 温流道模 | |
runner | 分流道 | |
runner plate | 流道板 | |
manifold block hot-runner manifold | 热流道板（柱） | |
warm runner plate | 温流道板 | |
runner puller. runner lock pin | 分流道拉料杆 | |
runner stripper plate | 推流道板 | |
fixed clamp plate, top clamping plate. top plate | 定模座板 | |
moving clamp plate. bottom clamping plate. bottom plate | 动模座板 | |
upper clamping plate | 上模座板 | |
lower clamping plate | 下模座板 | |
clamping force. locking force | 锁模力 | |
pin-point gate | 点浇口 | |
fixed clamp plate, top clamping plate. top plate | 定模座板 | |
moving clamp plate. bottom clamping plate. bottom plate | 动模座板 | |
upper clamping plate | 上模座板 | |
lower clamping plate | 下模座板 | |
angle pin. finger cam | 斜销 | |
guide pillar. guide pin. leader pin | 导柱 | |
guide pillar straight. straight leader pin | 带头导柱 | |
guide pillar. shouldered. shoulder leader pin | 带肩导柱 | |
ejector guide pillar. ejector guide pin | 推板导柱 | |
ejector plate return pin. push-back pin | 复位杆 | |
stop pin. stop button | 限位钉 | |
ejector pin | 推出零件/推杆 | |
ejector pin with cylindrical head | 圆柱头推杆 | |
shouldered ejector pin | 带肩推杆 | |
flat ejector pin | 扁推杆 | |
runner puller. runner lock pin | 分流道拉料杆 | |
clamping force. locking force | 锁模力 | |
dejection plate. ejector plate | 推板 | |
ejection force | 脱模力 | |
ring gate | 环形浇口 | |
horingontal parting line | 水平分型面(线) | |
thread ring. threaded cavity | 螺纹型环 | |
locating ring | 定位圈/限位零件 | |
stripper ring. strpper disk | 推件环/盘 | |
length bolt. puller bolt | 定矩拉杆 | |
side core. slide core | 侧型芯 | |
gate | 浇口 | |
direct gate spruce gate | 直接浇口 | |
ring gate | 环形浇口 | |
disk gate | 盘形浇口 | |
spoke gate spider gate | 轮辐浇口 | |
pin-point gate | 点浇口 | |
edge gate | 侧浇口 | |
submarine gate tunnel gate | 潜伏浇口 | |
ta be gate | 护耳浇口 | 健康零食前十名|
fan gate | 扇形浇口 | |
valve gate | 阀式浇口 | |
finger guide plate | 斜槽导板 | |
guide pillar. guide pin. leader pin | 导柱 | |
guide pillar straight. straight leader pin | 带头导柱 | |
guide pillar. shouldered. shoulder leader pin | 带肩导柱 | |
ejector guide pillar. ejector guide pin | 推板导柱 | |
guide bush. guide bushing | 导套 | |
guide fush, straight. shraighr bushing | 直导套 | |
guide fush, hended. shonlder bushing | 带头导套 | |
director guide fush. ejector bushing | 推板导套 | |
condary nozzle | 二级喷嘴 | |
cooling channel. cooling line | 冷却通道 | |
hot runner mould | 热流道模 | |
manifold block hot-runner manifold | 热流道板（柱） | |
shot capacity | 注射能力 | |
ejector housing. mould ba leg | 支架 | |
mould bas locating elements | 锥形定位件 | |
mould bas (of a injection mould) | 模架(注射模) | |
standard mould bas | 标准模架 | |
guide pillar. guide pin. leader pin | 导柱 | |
guide pillar straight. straight leader pin | 肥皂的制作带头导柱 | |
guide pillar. shouldered. shoulder leader pin | 带肩导柱 | |
cha. bolster. frame | 模套 | |
stationary mould fixed half | 定模 | |
movable mould moving half | 动模 | |
upper mould, upper half | 上模 | |
lower mould. lower half | 下模 | |
本文发布于:2023-07-29 19:42:33，感谢您对本站的认可！
本文链接：https://www.wtabcd.cn/fanwen/fan/89/1101163.html
版权声明：本站内容均来自互联网，仅供演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系，我们将在24小时内删除。
| 留言与评论（共有 0 条评论） |
