Shenzhen Sunlord Electronics Co., Ltd.
什么的纪律>发展党员制度
All products listed in this specification are developed, designed and intended for u in general electronics equipment. The products are not designed or warranted to meet the requirements of the applications listed below, who performance and/or quality require especially high reliability, or who failure, malfunction or trouble might directly cau damage to society, person, or property. Plea understand that we are not responsible for any damage or liability caud by u of the products in any of the applications below. Plea contact us for more details if you intend to u our products in the following applications.
1.Aircraft equipment
2.Aerospace equipment
3.Undera equipment
4.nuclear control equipment
5.military equipment
6.Power plant equipment
7.Medical equipment
8.Transportation equipment (automobiles, trains, ships,etc.)
9.Traffic signal equipment
10.Disaster prevention / crime prevention equipment
11.Data-processing equipment
12. Applications of similar complexity or with reliability requirements comparable to the applications listed in the above
This specification applies to CWS7060EF wire wound SMD type power inductors
2.
Product Description and Identification (Part Number) 1) Description
Wire Wound SMD Type Power Inductor,CWS7060EF, 2) Product Identification (Part Number)
CWS 7060 EF -XXX ① ② ③ ④
3.
Electrical Characteristics
Plea refer to Appendix A （Page 7）
1) Operating temperature (Including lf-generated heat): -40℃~+125℃
2) Storage temperature and humidity range (product with taping ): -10
℃~+40℃, RH 70% Max.
4.
Shape and Dimensions 1) Dimensions:
5.
Test and Measurement Procedures 5.1 Test Conditions
灵芝孢子粉副作用5.1.1 Unless otherwi specified, the standard atmospheric conditions for measurement/test as:
a. Ambient Temperature: 20±15℃
b. Relative Humidity: 65±20%
c. Air Pressure: 86 KPa to 106 KPa
5.1.2 If any doubt on the results, measurements/tests should be made within the following limits:
a. Ambient Temperature: 20±2℃
b. Relative Humidity: 65±5%
c. Air Pressure: 86KPa to 106 KPa
5.2 Visual Examination
a. Inspection Equipment: 20 X magnifier
爱的承诺5.3 Electrical Test
5.3.1 DC Resistance (DCR)
a. Refer to Appendix A .
b. Test equipment (Analyzer): HIOKI3540 or equivalent. 5.3.2 Impedance (Z)
a. Refer to Appendix A .
b. Test equipment: WK6500B or equivalent. 5.3.3 Rated Current
Unit: mm
如何经营感情ABC
Recommended pad
a. Refer to Appendix A.
b. Test equipment: Agilent E3633A, NF ZM2355, R2M-2H3 or equivalent..
c. Definition of Rated Current (Ir): Compare to the temperature ri approximate40℃, the smaller is Rated Current.(reference
environment temperature:25℃)保管室
5.4 Reliability Test
生日快乐日语The test samples shall be soldered to the test
6.
Packaging
6.1 Tape Carrier Packaging:
Packaging code: T
(1) Tape carrier packaging are specified in attached figure Fig.6.1-1~2 (2) Tape carrier packaging quantity:
a. Taping Drawings (Unit: mm)
Fig.6.1-1
b. Reel and Taping Dimensions (Unit: mm)
c. Peeling off force: 10gf to 130gf in the direction show below.
7.
Recommended Soldering Technologies 7.1 Re-flowing Profile: △ 1~2 ℃/c. Ramp
△ Pre-heating: 150~190℃/90±30 c. △ Time above 240℃: 20~40c
△ Peak temperature: 255℃ Max./5c; △ Solder paste: Sn/3.0Ag/0.5Cu △ Max.2 times for Re-flowing
8. Supplier Information
a) Supplier:
Shenzhen Sunlord Electronics Co., Ltd. b) Manufacturer:
Shenzhen Sunlord Electronics Co., Ltd. c) Manufacturing Address:
Sunlord Industrial Park, Dafuyuan Industrial Zone, Guanlan, Shenzhen, China Zip: 518110使用协议
255℃
200℃
150℃
Fig.6.1-2
