V alox* Resin 553
A sia Pacific: COMMERCIAL
30% GR PBT+PC, UL94 V-0. Reduced warpage characteristics.Applications; appliance handles, spotlights, electric motors, pump housings, etc.
T YPICAL PROPERTIES ¹
TYPICAL VALUE
UNIT
系列活动方案STANDARD
M ECHANICAL
T ensile Stress, brk, Type I, 5 mm/min
110M Pa A STM D 638
F lexural Stress, brk, 1.3 mm/min, 50 mm span 179M Pa A STM D 790F lexural Modulus, 1.3 mm/min, 50 mm span 6890M Pa A STM D 790H ardness, Rockwell R
118-A STM D 785I MPACT
Izod Impact, unnotched, 23°C 640J /m A STM D 4812 Izod Impact, notched, 23°C
85J /m A STM D 256T HERMAL
H DT, 0.45 MPa, 6.4 mm, unannealed 204°C A STM D 648H DT, 1.82 MPa, 6.4 mm, unannealed 160
°C A STM D 648 CTE, -40°C to 40°C, flow 2.16E-051/°C A STM E 831 CTE, 60°C to 138°C, flow 2.16E-051/°C A STM E 831R elative Temp Index, Elec
125°C U L 746B R elative Temp Index, Mech w/impact 110°C U L 746B R elative Temp Index, Mech w/o impact
125°C U L 746B P HYSICAL
S pecific Gravity 1.59-A STM D 792S pecific Volume
0.63c m³/g A STM D 792W ater Absorption, 24 hours
0.07%A STM D 570M old Shrinkage, flow, 1.5-3.2 mm (5)0.3 - 0.5%S ABIC Method M old Shrinkage, flow, 3.2-4.6 mm (5)0.5 - 0.8%S ABIC Method M old Shrinkage, xflow, 1.5-3.2 mm (5)0.4 - 0.6%S ABIC Method M old Shrinkage, xflow, 3.2-4.6 mm (5)
组长英文0.6 - 0.9%S ABIC Method E LECTRICAL
清肝降压胶囊
V olume Resistivity
4.3E+16O hm-cm A STM D 257D ielectric Strength, in air, 3.2 mm 18.8k V/mm A STM D 149D ielectric Strength, in oil, 1.6 mm 2
5.5k V/mm A STM D 149R elative Permittivity, 100 Hz 3.8-A STM D 150R elative Permittivity, 1 MHz
3.7
-
A STM D 150
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA DISCLAIMER : THE MATERIALS AND PRODUCTS OF THE BUSINESSES MAKING UP THE SABIC INNOVATIVE PLASTICS 1) T ypical values only. Variations within normal tolerances are possible for vario colours.All values are measured at least after 48 hours s torage at 230C/50% relative humidity.
All properties, except the melt volume rate are measured on injection m oulded samples.All samples are prepared according to ISO 294.
2) O nly typical data for material lection purpo.Not to be ud for p art or tool design.
3) T his rating is not intended to reflect hazards prented by this or any o ther material under actual fire conditions.4) O wn measurement according to UL.
5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to
differences in processing conditions, equipment, part geometry and tool design. It is recommended t
hat mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
Source, GMD, Last Update:04/14/2003
COMPANY, ITS SUBSIDIARIES AND AFFILIATES ("SABIC IP"), ARE SOLD SUBJECT TO SABIC IP' S STANDARD CONDITIONS OF SALE, WHICH ARE INCLUDED IN THE APPLICABLE DISTRIBUTOR OR OTHER SALES AGREEMENT, PRINTED ON THE BACK OF ORDER ACKNOWLEDGMENTS AND INVOICES, AND AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION, RECOMMENDATIONS, OR ADVICE
CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SABIC IP MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (I) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (II) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SABIC IP MATERIALS, PRODUCTS, RECOMMENDATIONS OR ADVICE. EXCEPT AS PROVIDED IN SABIC IP' S STANDARD CONDITIONS OF SALE, SABIC IP AND ITS REPRESENTATIVES SHALL IN NO EVENT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS OR PRODUCTS DESCRIBED HEREIN.
Each ur bears full responsibility for making its own determination as to the suitability of SABIC IP' s materials, products, recommendations, or advice for its own particular u. Each ur must identify and perform all tests and analys necessary to assure that its finished parts incorporating SABIC IP materials or products will be safe and suitable for u under end-u conditions. Nothing in this or any other document, nor any oral
recommendation or advice, shall be deemed to alter, vary, superde, or waive any provision of SABIC IP' s Standard Conditions of Sale or this Disclaimer, unless any such modification is specifically agreed to in a writing signed by SABIC IP. No statement contained herein concerning a possible or suggested u of any material, product or design is intended, or should be construed, to grant any licen under any patent or other intellectual property right of SABIC Innovative Plastics Company or any of its subsidiaries or affiliates covering such u or design, or as a recommendation for the u of such material, product or design in the infringement of any patent or other
V alox* Resin 553
A sia Pacific: COMMERCIAL
T YPICAL PROPERTIES ¹
TYPICAL VALUE UNIT STANDARD盆栽仙人掌
E LECTRICAL
D issipation Factor, 100 Hz 0.002-A STM D 150
医疗期的规定
泼水节的来历D issipation Factor, 1 MHz胜
0.02-A STM D 150A rc Resistance, Tungsten {PLC}6P
LC Code A STM D 495H ot Wire Ignition {PLC)
1P LC Code U L 746A H igh Voltage Arc Track Rate {PLC}3P LC Code U L 746A H igh Ampere Arc Ign, surface {PLC}3P LC Code U L 746A C omparative Tracking Index (UL) {PLC}
3P LC Code U L 746A F LAME CHARACTERISTICS
U L Recognized, 94V-0 Flame Class Rating (3)0.86m m U L 94U L Recognized, 94-5VA Rating (3)2.31m m U L 94
O xygen Index (LOI)
37.1%A STM D 2863U V-light, water exposure/immersion九层糕
F 1
-U L 746C
Source, GMD, Last Update:04/14/2003
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA DISCLAIMER : THE MATERIALS AND PRODUCTS OF THE BUSINESSES MAKING UP THE SABIC INNOVATIVE PLASTICS COMPANY, ITS SUBSIDIARIES AND AFFILIATES ("SABIC IP"), ARE SOLD SUBJECT TO SABIC IP' S STANDARD CONDITIONS OF SALE, WHICH ARE INCLUDED IN THE APPLICABLE DISTRIBUTOR OR OTHER SALES AGREEMENT, PRINTED ON THE BACK OF ORDER ACKNOWLEDGMENTS AND INVOICES, AND AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION, RECOMMENDATIONS, OR ADVICE
CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SABIC IP MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (I) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (II) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SABIC IP MATERIALS, PRODUCTS, RECOMMENDATIONS OR ADVICE. EXCEPT AS PROVIDED IN SABIC IP' S STANDARD CONDITIONS OF SALE, SABIC IP AND ITS REPRESENTATIVES SHALL IN NO EVENT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS OR PRODUCTS DESCRIBED HEREIN.Each ur bears full responsibility for making its own determination as to the suitability of SABIC IP' s materials, products, recommendations, or advice for its own particular u. Each ur must identify and perform all tests and analys necessary to assure that its finished parts incorporating SABIC IP materials or products will be safe and suitable for u under end-u conditions. Nothing in this or any other document, nor any oral
recommendation or advice, shall be deemed to alter, vary, superde, or waive any provision of SABIC IP' s Standard Conditions of Sale or this Disclaimer, unless any such modification is specifically agreed to in a writing signed by SABIC IP. No statement contained herein concerning a possible or suggested u of any material, product or design is intended, or should be construed, to
grant any licen under any patent or other intellectual property right of SABIC Innovative Plastics Company or any of its subsidiaries or affiliates covering such u or design, or as a recommendation for the u of such material, product or design in the infringement of any patent or other 1) T ypical values only. Variations within normal tolerances are possible for vario colours.All values are measured at least after 48 hours s torage at 230C/50% relative humidity.
All properties, except the melt volume rate are measured on injection m oulded samples.All samples are prepared according to ISO 294.
2) O nly typical data for material lection purpo.Not to be ud for p art or tool design.
3) T his rating is not intended to reflect hazards prented by this or any o ther material under actual fire conditions.4) O wn measurement according to UL.
5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to
differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
V alox* Resin 553
A sia Pacific: COMMERCIAL
P ROCESSING PARAMETERS
TYPICAL VALUE UNIT
I njection Molding
D rying Temperature 120°C D rying Time
3 - 4h rs D rying Time (Cumulative)12h rs M aximum Moisture Content 0.02
%M elt Temperature 250 - 265°C N ozzle Temperature
245 - 260°C F ront - Zone 3 Temperature 250 - 265°C M iddle - Zone 2 Temperature 245 - 260°C R
ear - Zone 1 Temperature 240 - 255°C M old Temperature 65 - 90°C B ack Pressure 0.3 - 0.7M Pa S crew Speed
50 - 80r pm S hot to Cylinder Size 40 - 80
%V ent Depth
0.025 - 0.038
m m
Source, GMD, Last Update:04/14/2003
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA DISCLAIMER : THE MATERIALS AND PRODUCTS OF THE BUSINESSES MAKING UP THE SABIC INNOVATIVE PLASTICS COMPANY, ITS SUBSIDIARIES AND AFFILIATES ("SABIC IP"), ARE SOLD SUBJECT TO SABIC IP' S STANDARD CONDITIONS OF SALE, WHICH ARE INCLUDED IN THE APPLICABLE DISTRIBUTOR OR OTHER SALES AGREEMENT, PRINTED ON THE BACK OF ORDER ACKNOWLEDGMENTS AND INVOICES, AND AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION, RECOMMENDATIONS, OR ADVICE
CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SABIC IP MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (I) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (II) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SABIC IP MATERIALS, PRODUCTS, RECOMMENDATIONS OR ADVICE. EXCEPT AS PROVIDED IN SABIC IP' S STANDARD CONDITIONS OF SALE, SABIC IP AND ITS REPRESENTATIVES SHALL IN NO EVENT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS OR PRODUCTS DESCRIBED HEREIN.Each ur bears full responsibility for making its own determination as to the suitability of SABIC IP' s materials, products, recommendations, or advice for its own particular u. Each ur must identify and perform all tests and analys necessary to assure that its finished parts incorporating SABIC IP materials or products will be safe and suitable for u under end-u conditions. Nothing in this or any other document, nor any oral
recommendation or advice, shall be deemed to alter, vary, superde, or waive any provision of SABIC IP' s Standard Conditions of Sale or this Disclaimer, unless any such modification is specifically agreed to in a writing signed by SABIC IP. No statement contained herein concerning a possible or suggested u of any material, product or design is intended, or should be construed, to
grant any licen under any patent or other intellectual property right of SABIC Innovative Plastics Company or any of its subsidiaries or affiliates covering such u or design, or as a recommendation for the u of such material, product or design in the infringement of any patent or other 1) T ypical values only. Variations within normal tolerances are possible for vario colours.All values are measured at least after 48 hours s torage at 230C/50% relative humidity.
All properties, except the melt volume rate are measured on injection m oulded samples.All samples are prepared according to ISO 294.
2) O nly typical data for material lection purpo.Not to be ud for p art or tool design.
3) T his rating is not intended to reflect hazards prented by this or any o ther material under actual fire conditions.4) O wn measurement according to UL.
5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to
differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
