L exan* Resin 241R
A sia Pacific: COMMERCIAL
10.5 MFR. Improved flame retardance. Internal mold relea.
T YPICAL PROPERTIES ¹
TYPICAL VALUE UNIT STANDARD
M ECHANICAL
T ensile Stress, yld, Type I, 50 mm/min 630k gf/cm²A STM D 638T ensile Stress, brk, Type I, 50 mm/min 700k gf/cm²A STM D 638T ensile Strain, yld, Type I, 50 mm/min 7%A STM D 638T ensile Strain, brk, Type I, 50 mm/min
130%
A STM D 638F lexural Stress, yld, 1.3 mm/min, 50 mm span 980k gf/cm²A STM D 790F lexural Modulus, 1.3 mm/min, 50 mm span 23900k gf/cm²A STM D 790H ardness, Rockwell M 70-A STM D 785H ardness, Rockwell R
118-A STM D 785T aber Abrasion, CS-17, 1 kg
10m g/1000cy A STM D 1044I MPACT
Izod Impact, unnotched, 23°C 326c m-kgf/cm A STM D 4812 Izod Impact, notched, 23°C 81c m-kgf/cm A STM D 256T ensile Impact, Type S
589c m-kgf/cm²A STM D 1822 Falling Dart Impact (D 3029), 23°C
1728c m-kgf A STM D 3029 Instrumented Impact Energy @ peak, 23°C
650c m-kgf A STM D 3763T HERMAL
V icat Softening Temp, Rate B/50
154°C A STM D 1525H DT, 0.45 MPa, 6.4 mm, unannealed 137°C A STM D 648H DT, 1.82 MPa, 6.4 mm, unannealed 132
°C A STM D 648 CTE, -40°C to 95°C, flow 6.84E-051/°C A STM E 831S pecific Heat
1.25J /g-°C A STM C 351T hermal Conductivity
0.27W /m-°C A STM C 177R elative Temp Index, Elec
130
°C
U L 746B
Source, GMD, Last Update:
人间失格名句PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA.
DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SABIC INNOVATIVE PLASTICS HOLDING BV, ITS SUBSIDIARIES AND AFFILIATES ("SELLER"), ARE SOLD SUBJECT TO SELLER'S STANDARD CONDITIONS OF SALE, WHICH CAN BE FOUND AT AND ARE AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION OR RECOMME
正版windows
NDATION CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SELLER MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (i) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SELLER'S PRODUCTS,SERVICES OR RECOMMENDATIONS. EXCEPT AS PROVIDED IN SELLER'S STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS PRODUCTS OR SERVICES DESCRIBED HEREIN. Each ur is responsible for making its own determination as to the suitability of Seller's products, rvices or recommendations for the ur's particular u through appropriate end-u testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller's Standard Conditions of Sale or this Disclaimer,unless it is specifically agreed to in a writing signed Seller. No statement Seller concerning a possible u of any product, rvice or design is intended, or should be construed, to grant any licen under any patent or other intellectual property right of Seller or as a recommendation for the u of such product, rvice or design in a manner that infringes any patent or other intellectual property right.SABIC Innovative Plastics is a trademark of SABIC Holding Europe BV 1) T ypical values only. Variations within normal tolerances are possible for vario colours.All values are measured at least after 48 hours s torage at 230C/50% relative humidity.
All properties, expect the melt volume rate are measured on injection m oulded samples.All samples are prepared according to ISO 294.
2) O nly typical data for material lection purpo.Not to be ud for p art or tool design.
3) T his rating is not intended to reflect hazards prented this or any o ther material under actual fire conditions.4) O wn measurement according to UL.关于愿望的作文
5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to
differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
L exan* Resin 241R
A sia Pacific: COMMERCIAL
T YPICAL PROPERTIES ¹
TYPICAL VALUE UNIT STANDARD
T HERMAL
R elative Temp Index, Mech w/impact 130°C
U L 746B R elative Temp Index, Mech w/o impact
130°C U L 746B P HYSICAL
外贸依存度S pecific Gravity 1.2-A STM D 792S pecific Volume 0.83c m³/g A STM D 792D ensity
1.19g /cm³A STM D 792W ater Absorption, 24 hours
0.15%A STM D 570W ater Absorption, equilibrium, 23C 0.35%A STM D 570 Water Absorption, equilibrium, 100°C 0.58%A STM D 570M old Shrinkage, flow, 3.2 mm (5)0.5 - 0.7%
S ABIC Method Melt Flow Rate, 300°C/1.2 kgf
10.5g /10 min A STM D 1238O PTICAL
协管
L ight Transmission, 2.54 mm 88%A STM D 1003H aze, 2.54 mm 1%A STM D 1003R efractive Index
1.586-A STM D 542E LECTRICAL
V olume Resistivity
>1.E+17O hm-cm A STM D 257D ielectric Strength, in air, 3.2 mm 14.9k V/mm A STM D 149R elative Permittivity, 50/60 Hz 3.17-A STM D 150R elative Permittivity, 1 MHz 2.96-A STM D 150D issipation Factor, 50/60 Hz 0.0009-A STM D 150D issipation Factor, 1 MHz 0.01-A STM D 150H ot Wire Ignition {PLC)
2P LC Code U L 746A H igh Voltage Arc Track Rate {PLC}2P LC Code U L 746A H igh Ampere Arc Ign, surface {PLC}1P LC Code U L 746A C omparative Tracking Index (UL) {PLC}
2
P LC Code
U L 746A
DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SABIC INNOVATIVE PLASTICS HOLDING BV, ITS SUBSIDIARIES AND AFFILIATES ("SELLER"), ARE SOLD SUBJECT TO SELLER'S STANDARD Source, GMD, Last Update:
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA.
CONDITIONS OF SALE, WHICH CAN BE FOUND AT AND ARE AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION OR RECOMMENDATION CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SELLER MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (i) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SELLER'S PRODUCTS,SERVICES OR RECOMMENDATIONS. EXCEPT AS PROVIDED IN SELLER'S STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS PRODUCTS OR SERVICES DESCRIBED HEREIN. Each ur is responsible for making its own determination as to the suitability of Seller's products, rvices or recommendations for the ur's particular u through appropriate end-u testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller's Standard Conditions of Sal
e or this Disclaimer,unless it is specifically agreed to in a writing signed Seller. No statement Seller concerning a possible u of any product, rvice or design is intended, or should be construed, to grant any licen under any patent or other intellectual property right of Seller or as a recommendation for the u of such product, rvice or design in a manner that infringes any patent or other intellectual property right.1) T ypical values only. Variations within normal tolerances are possible for vario colours.All values are measured at least after 48 hours s torage at 230C/50% relative humidity.
郑远海All properties, expect the melt volume rate are measured on injection m oulded samples.All samples are prepared according to ISO 294.
2) O nly typical data for material lection purpo.Not to be ud for p art or tool design.
3) T his rating is not intended to reflect hazards prented this or any o ther material under actual fire conditions.4) O wn measurement according to UL.
5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to
differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
L exan* Resin 241R
A sia Pacific: COMMERCIAL
T YPICAL PROPERTIES ¹
TYPICAL VALUE UNIT STANDARD
F LAME CHARACTERISTICS
U L Recognized, 94V-2 Flame Class Rating (3)1.09m m U L 94
U L Recognized, 94V-0 Flame Class Rating (3)5.99m m U L 94U V-light, water exposure/immersion
F 2
-U L 746C
Source, GMD, Last Update:
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA.
DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SABIC INNOVATIVE PLASTICS HOLDING BV, ITS SUBSIDIARIES AND AFFILIATES ("SELLER"), ARE SOLD SUBJECT TO SELLER'S STANDARD CONDITIONS OF SALE, WHICH CAN BE FOUND AT AND ARE AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION OR RECOMMENDATION CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SELLER MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (i) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SELLER'S PRODUCTS,SERVICES OR RECOMMENDATIONS. EXCEPT AS PROVIDED IN SELLER'S STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS PRODUCTS OR SERVICES DESCRIBED HEREIN. Each ur is responsible for making its own determination as to the suitability of Seller's products, rvices
or recommendations for the ur's particular u through appropriate end-u testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller's Standard Conditions of Sale or this Disclaimer,unless it is specifically agreed to in a writing signed Seller. No statement Seller concerning a possible u of any product, rvice or design is intended, or should be construed, to grant any licen under any patent or other intellectual property right of Seller or as a recommendation for the u of such product, rvice or design in a manner that infringes any patent or other intellectual property right.1) T ypical values only. Variations within normal tolerances are possible for vario colours.All values are measured at least after 48 hours s torage at 230C/50% relative humidity.
All properties, expect the melt volume rate are measured on injection m oulded samples.All samples are prepared according to ISO 294.
2) O nly typical data for material lection purpo.Not to be ud for p art or tool design.
3) T his rating is not intended to reflect hazards prented this or any o ther material under actual fire conditions.4) O wn measurement according to UL.
5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range du
e to
differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
L exan* Resin 241R
A sia Pacific: COMMERCIAL
P ROCESSING PARAMETERS
TYPICAL VALUE UNIT
蝠的组词I njection Molding
D rying Temperature 120°C D rying Time
3 - 4h rs D rying Time (Cumulative)48h rs M aximum Moisture Content 0.02
%M elt Temperature 295 - 315°C N ozzle Temperature
290 - 310°C F ront - Zone 3 Temperature 295 - 315°C M iddle - Zone 2 Temperature 280 - 305°C R ear - Zone 1 Temperature 270 - 295°C M old Temperature 70 - 95°C B ack Pressure 0.3 - 0.7M Pa S crew Speed
40 - 70r pm S hot to Cylinder Size 40 - 60
%V ent Depth
0.025 - 0.076
m m
Source, GMD, Last Update:
乌镇景区
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA.
DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SABIC INNOVATIVE PLASTICS HOLDING BV, ITS SUBSIDIARIES AND AFFILIATES ("SELLER"), ARE SOLD SUBJEC
T TO SELLER'S STANDARD CONDITIONS OF SALE, WHICH CAN BE FOUND AT AND ARE AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION OR RECOMMENDATION CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SELLER MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (i) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SELLER'S PRODUCTS,SERVICES OR RECOMMENDATIONS. EXCEPT AS PROVIDED IN SELLER'S STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS PRODUCTS OR SERVICES DESCRIBED HEREIN. Each ur is responsible for making its own determination as to the suitability of Seller's products, rvices or recommendations for the ur's particular u through appropriate end-u testing and analysis. Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller's Standard Conditions of Sale or this Disclaimer,unless it is specifically agreed to in a writing signed Seller. No statement Seller concerning a possible u of any product, rvice or design is intended, or should be construed, to grant any licen under any patent or other intellectual property right of Seller or as a recommendation for the u of such product, rvice or design in a manner that infringes any patent or other intellectual property right.1) T ypical values only. Variations
within normal tolerances are possible for vario colours.All values are measured at least after 48 hours s torage at 230C/50% relative humidity.
All properties, expect the melt volume rate are measured on injection m oulded samples.All samples are prepared according to ISO 294.
2) O nly typical data for material lection purpo.Not to be ud for p art or tool design.
3) T his rating is not intended to reflect hazards prented this or any o ther material under actual fire conditions.4) O wn measurement according to UL.
5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to
differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
