C YCOLOY™ Resin CY6414
E urope-Africa-Middle East: COMMERCIAL
Flame retardant modified PC blend using non-brominated and non-chlorinated flame retardant systems, offering high heat for application in appliances, lighting and electrical market.
TYPICAL PROPERTIES¹
TYPICAL VALUE Unit Standard
M ECHANICAL
T ensile Stress, yld, Type I, 50 mm/min
650
k gf/cm²A STM D 638T ensile Stress, brk, Type I, 50 mm/min 630k gf/cm²A STM D 638T ensile Strain, yld, Type I, 50 mm/min 6%A STM D 638T ensile Strain, brk, Type I, 50 mm/min 85%
A STM D 638T ensile Modulus, 5 mm/min
23700k gf/cm²A STM D 638T ensile Stress, yield, 50 mm/min 66M Pa I SO 527T ensile Stress, break, 50 mm/min 67M Pa I SO 527T ensile Strain, yield, 50 mm/min 5.7%I SO 527T ensile Strain, break, 50 mm/min >100%I SO 527T ensile Modulus, 1 mm/min 2420M Pa I SO 527F lexural Stress, yield, 2 mm/min 96M Pa I SO 178F lexural Modulus, 2 mm/min
2470
M Pa I SO 178
I MPACT
Izod Impact, unnotched 80*10*4 +23°C
N B
红烧鹌鹑k J/m²I SO 180/1U Izod Impact, notched 80*10*4 +23°C 50k J/m²I SO 180/1A Izod Impact, notched 80*10*4 0°C 14k J/m²I SO 180/1A Izod Impact, notched 80*10*4 -30°C
12k J/m²I SO 180/1A Charpy 23°C, V-notch Edgew 80*10*3 sp=62mm 28k J/m²I SO 179/1eA Charpy 0°C, V-notch Edgew 80*10*3 sp=62mm 17k J/m²I SO 179/1eA Charpy -30°C, V-notch Edgew 80*10*3 sp=62mm
12
k J/m²I SO 179/1eA
T HERMAL
H DT, 1.82 MPa, 6.4 mm, unannealed
118
°C A STM D 648 CTE, -40°C to 40°C, flow
7.E-05
1/°C
I SO 11359-2
Source GMD, last updated:
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA
DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SAUDI BASIC INDUSTRIES CORPORATION (SABIC) OR ITS SUBSIDIARIES OR AFFILIATES ( S ELLER ) ARE SOLD SUBJECT TO SELLER S STANDARD CONDITIONS OF SALE, WHICH ARE AVAILABLE UPON REQUEST. INFORMATION AND RECOMMENDATIONS CONTAINED IN THIS DOCUMENT ARE GIVEN IN GOOD FAITH. HOWEVER, SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATION, WARRANTY OR GUARANTEE (i) THAT ANY RESULTS DESCRIBED IN THIS DOCUMENT WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN OR APPLICATION INCORPORATING SELLER S MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS. UNLESS OTHERWISE PROVIDED IN SELLER S
STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS DESCRIBED IN THIS DOCUMENT.
Each ur is responsible for making its own determination as to the suitability of Seller s materials, products, rvices or recommendations for the ur s particular u through appropriate end-u and other testing and analysis.Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller s Standard Conditions of Sale or this Disclaimer, unless it is specifically agreed to in a writing signed by Seller. Statements by Seller concerning a possible u of any material, product, rvice or design do not, are not intended to, and should not be construed to grant any licen under any patent or other intellectual property right of Seller or as a (1) Typical values only. Variations within normal tolerances are possible for various colors. All values are
逆向而行measured after at least 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
(2) Only typical data for lection purpos. Not to be ud for part or tool design.
(3) This rating is not intended to reflect hazards prented by this or any other material under actual fire conditions.
(4) Internal measurements according to UL standards.
(5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.(6) Needs hard coat to consistently pass 60 c Vertical Burn.
C YCOLOY™ Resin CY6414
E urope-Africa-Middle East: COMMERCIAL
TYPICAL PROPERTIES¹
TYPICAL VALUE Unit Standard
山大威海分校T HERMAL
CTE, -40°C to 40°C, xflow
7.E-05
乡村振兴战略1/°C I SO 11359-2 Ball Pressure Test, 125°C +/- 2°C
P ass -I EC 60695-10-2 Ball Pressure Test, 125°C +/- 2°C, by VDE P ass -I EC 60695-10-2V icat Softening Temp, Rate B/50133°C I SO 306V icat Softening Temp, Rate B/120
134°C I SO 306H DT/Af, 1.8 MPa Flatw 80*10*4 sp=64mm 116°C I SO 75/Af R elative Temp Index, Elec
中班班级计划
105°C U L 746B R elative Temp Index, Mech w/impact 95°C U L 746B R elative Temp Index, Mech w/o impact
100
°C U L 746B
P HYSICAL
M old Shrinkage, flow, 3.2 mm (5)
0.4 - 0.8
%
S ABIC Method D ensity
1.18g /cm³I SO 1183 Water Absorption, (23°C/sat)
0.3%I SO 62 Moisture Absorption (23°C / 50% RH)0.1%
I SO 62 Melt Volume Rate, MVR at 260°C/5.0 kg
13
c m³/10 min I SO 1133
E LECTRICAL
R elative Permittivity, 1 kHz
3.01
-A STM D 150R elative Permittivity, 1 MHz 2.95-A STM D 150D issipation Factor, 1 kHz 0.0017-A STM D 150D issipation Factor, 1 MHz 0.0088-A STM D 150H ot Wire Ignition {PLC)
2P LC Code U L 746A H igh Ampere Arc Ign, surface {PLC}1P LC Code U L 746A C omparative Tracking Index (UL) {PLC}3
P LC Code U L 746A V olume Resistivity
1.E+15O hm-cm I EC 60093S urface Resistivity, ROA
4.E+16
O hm
I EC 60093
DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SAUDI BASIC INDUSTRIES C
ORPORATION (SABIC) OR ITS SUBSIDIARIES OR AFFILIATES ( Each ur is responsible for making its own determination as to the suitability of Seller Source GMD, last updated:
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA
S ELLER ) ARE SOLD SUBJECT TO SELLER S STANDARD CONDITIONS OF SALE, WHICH ARE AVAILABLE UPON REQUEST. INFORMATION AND RECOMMENDATIONS CONTAINED IN THIS DOCUMENT ARE GIVEN IN GOOD FAITH. HOWEVER, SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATION, WARRANTY OR GUARANTEE (i) THAT ANY RESULTS DESCRIBED IN THIS DOCUMENT WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN OR APPLICATION INCORPORATING SELLER S MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS. UNLESS OTHERWISE PROVIDED IN SELLER S
STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS DESCRIBED IN THIS DOCUMENT.
s materials, products, rvices or recommendations for the ur s particular u through appropriat
e end-u and other testing and analysis.Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller s Standard Conditions of Sale or this Disclaimer, unless it is specifically agreed to in a writing signed by Seller. Statements by (1) Typical values only. Variations within normal tolerances are possible for various colors. All values are
measured after at least 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
(2) Only typical data for lection purpos. Not to be ud for part or tool design.
(3) This rating is not intended to reflect hazards prented by this or any other material under actual fire conditions.
(4) Internal measurements according to UL standards.
(5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.(6) Needs hard coat to consistently pass 60 c Vertical Burn.
C YCOLOY™ Resin CY6414
E urope-Africa-Middle East: COMMERCIAL
TYPICAL PROPERTIES¹
TYPICAL VALUE Unit Standard
E LECTRICAL文科考研
D issipation Factor, 1 MHz
0.008
一曝十寒什么意思-
I EC 60250F LAME CHARACTERISTICS
U L Recognized, 94V-0 Flame Class Rating (3)
1.2m m U L 94
U L Recognized, 94-5VB Rating (3)
2.5m m U L 94
Glow Wire Flammability Index 960°C, pass at, by VDE 0.75m m I EC 60695-2-12G low Wire Ignitability Temperature, 0.75 mm, by VDE 775°C I EC 60695-2-13G low Wire Ignitability Temperature, 1.5 mm, by VDE 775°C I EC 60695-2-13G low Wire Ignitability Temperature, 3.0 mm, by VDE 775°C I EC 60695-2-13O xygen Index (LOI)
32
%
I SO 4589
Source GMD, last updated:
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA
DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SAUDI BASIC INDUSTRIES CORPORATION (SABIC) OR ITS SUBSIDIARIES OR AFFILIATES ( S ELLER ) ARE SOLD SUBJECT TO SELLER S STANDARD CONDITIONS OF SALE, WHICH ARE AVAILABLE UPON REQUEST. INFORMATION AND RECOMMENDATIONS CONTAINED IN THIS DOCUMENT ARE GIVEN IN GOOD FAITH. HOWEVER, SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATION, WARRANTY OR GUARANTEE (i) THAT ANY RESULTS DESCRIBED IN THIS DOCUMENT WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN OR APPLICATION INCORPORATING SELLER S MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS. UNLESS OTHERWISE PROVIDED IN SELLER S
STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS DESCRIBED IN THIS DOCUMENT.
Each ur is responsible for making its own determination as to the suitability of Seller s materials, p
roducts, rvices or recommendations for the ur s particular u through appropriate end-u and other testing and analysis.Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller s Standard Conditions of Sale or this Disclaimer, unless it is specifically agreed to in a writing signed by Seller. Statements by (1) Typical values only. Variations within normal tolerances are possible for various colors. All values are
measured after at least 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
(2) Only typical data for lection purpos. Not to be ud for part or tool design.
时光匆匆的句子
(3) This rating is not intended to reflect hazards prented by this or any other material under actual fire conditions.
(4) Internal measurements according to UL standards.
(5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recomm
ended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.(6) Needs hard coat to consistently pass 60 c Vertical Burn.
C YCOLOY™ Resin CY6414
E urope-Africa-Middle East: COMMERCIAL
PROCESSING PARAMETERS
TYPICAL VALUE Unit
I njection Molding
D rying Temperature 90 - 100°C D rying Time
2 - 4h rs M aximum Moisture Content 0.02
%M elt Temperature 250 - 300°C N ozzle Temperature
230 - 290°C F ront - Zone 3 Temperature 240 - 300°C M iddle - Zone 2 Temperature 230 - 290°C R ear - Zone 1 Temperature 210 - 260°C H opper Temperature 60 - 80°C M old Temperature
60 - 90
°C
Source GMD, last updated:
PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA
DISCLAIMER : THE MATERIALS, PRODUCTS AND SERVICES OF SAUDI BASIC INDUSTRIES CORPORATION (SABIC) OR ITS SUBSIDIARIES OR AFFILIATES ( S ELLER ) ARE SOLD SUBJECT TO SELLER S STANDARD CONDITIONS OF SALE, WHICH ARE AVAILABLE UPON REQUEST. INFORMATION AND RECOMMENDATIONS CONTAINED IN THIS DOCUMENT ARE GIVEN IN GOOD FAITH. HOWEVER, SELLER MAKES NO EXPRESS OR IMPLIED REPRESENTATION, WARRANTY OR GUARANTEE (i) THAT ANY RESULTS DESCRIBED IN THIS DOCUMENT WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN OR APPLICATION INCORPORATING SELLER S
MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS. UNLESS OTHERWISE PROVIDED IN SELLER S
STANDARD CONDITIONS OF SALE, SELLER SHALL NOT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS, SERVICES OR RECOMMENDATIONS DESCRIBED IN THIS DOCUMENT.
Each ur is responsible for making its own determination as to the suitability of Seller s materials, products, rvices or recommendations for the ur s particular u through appropriate end-u and other testing and analysis.Nothing in any document or oral statement shall be deemed to alter or waive any provision of Seller s Standard Conditions of Sale or this Disclaimer, unless it is specifically agreed to in a writing signed by Seller. Statements by (1) Typical values only. Variations within normal tolerances are possible for various colors. All values are
measured after at least 48 hours storage at 23°C/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
(2) Only typical data for lection purpos. Not to be ud for part or tool design.
(3) This rating is not intended to reflect hazards prented by this or any other material under actual fire conditions.
(4) Internal measurements according to UL standards.
(5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.(6) Needs hard coat to consistently pass 60 c Vertical Burn.
