HIGH SPEED-10 MBit/s
LOGIC GATE OPTOCOUPLERS
HCPL-0600HCPL-0601
撞球游戏DESCRIPTION
The HCPL-0600/0601optocouplers consist of a 870 nm AlGaAS LED, optically coupled to a very high speed integrated photo-detector logic gate with a strobable output. The devices are houd in a compact small-outline package. This output features an open collector, thereby permitting wired OR outputs. The coupled parameters are guaranteed over the temperature range of -40°C to +85°C. A maximum input signal of 5 mA will provide a minimum output sink current of 13 mA (fan out of 8). An internal noi
A 0.1 µF bypass capacitor must be connected between pins 8 and 5. (See note 1)
HIGH SPEED-10 MBit/s
LOGIC GATE OPTOCOUPLERS HCPL-0600HCPL-0601
*6.3 mA is a guard banded value which allows for at least 20% CTR degradation. Initial input current threshold value is 5.0 mA or less
HIGH SPEED-10 MBit/s
关长云LOGIC GATE OPTOCOUPLERS HCPL-0600HCPL-0601
ELECTRICAL CHARACTERISTICS (T A = -40°C to +85°C Unless otherwi specified.)
INDIVIDUAL COMPONENT CHARACTERISTICS
Parameter Test Conditions Symbol Min Typ**Max Unit
EMITTER(I F = 10 mA)
V F 1.8
V
Input Forward Voltage T A =25°C 1.75
Input Rever Breakdown Voltage (I R = 10 µA)B VR 5.0V Input Capacitance(V F = 0, f = 1 MHz)C IN60pF Input Diode T emperature Coefficient(I F = 10 mA)∆VF/∆T A-1.4mV/°C DETECTOR
High Level Supply Current (V CC = 5.5 V, I F = 0 mA)
(V E = 0.5 V)
I CCH710mA
Low Level Supply Current (V CC = 5.5 V, I F = 10 mA)
(V E = 0.5 V)
I CCL913mA
Low Level Enable Current(V CC = 5.5 V, V E = 0.5 V)I EL-0.8-1.6mA High Level Enable Current(V CC = 5.5 V, V E = 2.0 V)I EH-0.6-1.6mA High Level Enable Voltage(V CC = 5.5 V, I F = 10 mA)V EH 2.0V Low Level Enable Voltage(V CC = 5.5 V, I F = 10 mA) (Note 2)V EL0.8V
SWITCHING CHARACTERISTICS (T A = -40°C to +85°C, V CC = 5 V, I F = 7.5 mA Unless otherwi specified.) AC Characteristics Test Conditions Device Symbol Min Typ Max Unit
清廉的意思Propagation Delay Time to Output High Level
(Note 3)(T A =25°C)
All T PLH
204575
ns (R L = 350Ω, C L = 15 pF) (Fig. 12)100
Propagation Delay Time to Output Low Level
(Note 4)(T A =25°C)
说课比赛All T PHL
254575
ns (R L = 350Ω, C L = 15 pF) (Fig. 12)100
Pul Width Distortion(R L = 350Ω, C L = 15 pF) (Fig. 12)All|T PHL-T PLH|335ns
Output Ri Time (10-90%)(R L = 350Ω, C L = 15 pF)
(Note 5) (Fig. 12)
All t r50ns
Output Fall Time (90-10%)(R L = 350Ω, C L = 15 pF)
(Note 6) (Fig. 12)
All t f12ns
Enable Propagation Delay Time
to Output High Level (I F = 7.5 mA, V EH = 3.5 V)
(R L = 350Ω, C L = 15 pF)
(Note 7) (Fig. 13)
软装设计师
All t ELH20ns
Enable Propagation Delay Time
to Output Low Level (I F = 7.5 mA, V EH = 3.5 V)
(R L = 350Ω, C L = 15 pF)
(Note 8) (Fig. 13)
All t EHL20ns
Common Mode
T ransient Immunity (at Output High Level)
(R L = 350Ω) (T A =25°C)
(I F = 0 mA, V OH (Min.) = 2.0 V)
(Note 9)(Fig. 14)
烧饼做法|V CM| = 10 V HCPL-0600
|CM H|
10,000安卓模拟器按键
V/µs
|V CM| = 50 V HCPL-0601500010,000
三十六计大全Common Mode
T ransient Immunity (at Output Low Level)
(R L = 350Ω) (T A =25°C)
(I F = 7.5 mA, V OL (Max.) = 0.8 V)
(Note 10)(Fig. 14)
|V CM| = 10 V HCPL-0600
|CM H|
10,000
V/µs
|V CM| = 50 V HCPL-0601500010,000
HCPL-0600
HCPL-0601
** All typical values are at V CC = 5 V , T A = 25°C
1.The V CC supply to each optoisolator must be bypasd by a 0.1µF capacitor or larger. This can be either a ceramic or solid
tantalum capacitor with good high frequency characteristic and should be connected as clo as possible to the package V CC and GND pins of each device.2.Enable Input - No pull up resistor required as the device has an internal pull up resistor.
3.t PLH - Propagation delay is measured from the 3.75 mA level on the HIGH to LOW transition of the input current pul to the
1.5V level on the LOW to HIGH transition of the output voltage pul. 4.t PHL - Propagation delay is measured from the 3.75 mA level on the LOW to HIGH transition of the input current pul to the
1.5V level on the HIGH to LOW transition of the output voltage pul.5. t r - Ri time is measured from the 90% to the 10% levels on the LOW to HIGH transition of the output pul.6.t f - Fall time is measured from the 10% to the 90% levels on the HIGH to LOW transition of the output pul.
7.t ELH - Enable input propagation delay is measured from the 1.5V level on the HIGH to LOW transition of the input voltage pul
to the 1.5V level on the LOW to HIGH transition of the output voltage pul.8.t EHL - Enable input propagation delay is measured from the 1.5V level on the LOW to HIGH transition of the input voltage pul
to the 1.5V level on the HIGH to LOW transition of the output voltage pul.9.CM H - The maximum tolerable rate of ri of the common mode voltage to ensure the output will remain in the high state (i.e.,
V OUT > 2.0 V). Measured in volts per microcond (V/µs).10.CM L - The maximum tolerable rate of fall of the common mode voltage to ensure the output will remain in the low output state
(i.e., V OUT < 0.8 V). Measured in volts per microcond (V/µs).11.Device considered a two-terminal device: Pins 1,2,3 and 4 shorted together, and Pins 5,6,7 and 8 shorted together.
TRANSFER CHARACTERISTICS (T A = -40°C to +85°C Unless otherwi specified.)
DC Characteristics Test Conditions
Symbol Min
Typ**
Max Unit High Level Output Current (V CC = 5.5 V , V O = 5.5 V)
(I F = 250 µA, V E = 2.0 V) (Note 2)I OH 100µA Low Level Output Voltage (V CC = 5.5 V , I F = 5 mA)
(V E = 2.0 V , I OL = 13 mA) (Note 2)
V OL .350.6V Input Threshold Current
(V CC = 5.5 V , V O = 0.6 V ,V E = 2.0 V , I OL = 13 mA)
I FT
3
5
mA
ISOLATION CHARACTERISTICS (T A = -40°C to +85°C Unless otherwi specified.)
Characteristics
Test Conditions
Symbol
Min
Typ**
Max
Unit
Input-Output
Insulation Leakage Current (Relative humidity = 45%)
(T A = 25°C, t = 5 s)(V I-O = 3000 VDC)
(Note 11)I I-O
1.0*µA
Withstand Insulation T est Voltage (R H < 50%, T A = 25°C)(Note 11) ( t = 1 min.)V ISO 2500
V RMS Resistance (Input to Output)(V I-O = 500 V) (Note 11)R I-O 1012ΩCapacitance (Input to Output)
(f = 1 MHz) (Note 11)
C I-O
0.6
pF
NOTES
HCPL-0600HCPL-0601 TYPICAL PERFORMANCE CURVES
