TOSHIBA Photocoupler GaA ℓAs IRed & Photo −IC
TLP113
Isolated Line Receiver
Simplex / Multiplex Data Transmission Computer −Peripheral Interface Microprocessor System Interface
Digital Isolation For A / D, D / A Conversion
The TOSHIBA mini flat coupler TLP113 is a small outline coupler, suitable for surface mount asmbly.
TLP113 consists of a GaA ℓAs light emitting diode, optically coupled to an integrated high gain, high speed photodetector who output is an open collector, schottky clamped transistor.
z Input current thresholds: I F =10mA(max.) z Switching speed: 10MBd(typ.) z TTL / LSTTL compatible: V CC =5V减肥器材
z Guaranteed performance over temp.: 0~70°C z Isolation voltage: 2500Vrms(min.)
z UL recognized: UL1577 file no. E67349
Schematic
V CC GND
V O
43
V F
(Note) A 0.1μF bypass capacitor must be connected between pins 4 and 6.
Pin Configuration (top view)
1 : Anode
3 : Cathode
4 : GND
5 : Output
(Open collector) 6 : V
CC
1
3
4
5
古典仙侠类小说6
Unit in mm
TOSHIBA 11−4C2 Weight: 0.09 g (typ.) INPUT
OUTPUT
招财图
祝福朋友的句子H H
L L
TRUTH TABLE (Positive Logic)
Absolute Maximum Ratings (Ta = 25°C)
Characteristic Symbol Rating Unit
Forward current I F
20 mA
Pul forward current
(Note 1)
I FP 40 mA
Peak transient forward
儿童插画
current (Note 2)I FPT 1 A
L E D
Rever voltage V R 5 V Output current
I O
25 mA
Output voltage V O 7 V Supply voltage
(1 minute maximum) V CC 7 V D e t e c t o r
Output power dissipation
P O 40 mW Operating temperature range T opr −40~85 °C Storage temperature range T stg
−55~125
°C
Lead solder temperature (10s) T sol 260 °C Isolation voltage
(AC, 1 min., RH ≤ 60%,
Note 4)
BV S 2500
Vrms
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cau this product to decrea in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges.
Plea design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). (Note 1) 50% duty cycle, 1ms pul width. (Note 2) Pul width ≤1μs, 300pps.
Recommended Operating Conditions
Characteristic Symbol Min. Typ. Max. Unit
Input voltage, low level V FL
−3 0 1.0 V
Input current, high level I FH 13* 16 20 mA Supply voltage** V CC 4.5 5 5.5 V Fan out
(TTL load, each channel) N
―
― 8 ―
Operating temperature
T opr 0 ― 70 °C
Note: Recommended operating conditions are given as a design guideline to obtain expected perfor
mance of the device. Additionally, each item is an independent guideline respectively. In developing designs using this product, plea confirm specified characteristics shown in this document.
* 13mA is a guard banded value which allows for at least 20% CTR degradation.
Initial input current threshold value is 10mA or less.
**This item denotes operating ranges, not meaning of recommended operating conditions.
Electrical Characteristics(unless otherwi specified, Ta=0~70°C, V CC=4.5~5.5V,
V FL≤ 1.0V)
Characteristic Symbol Test
Condition Min.
Typ.
Max.
Unit Forward voltage V F I F=10mA, Ta=25°C ― 1.65 1.80 V Forward voltage
temperature coefficient
V F / Ta I F=10mA ―−2 ―mV / °C Rever current I R V R=5V, Ta=25°C ―― 10 μA
Capacitance between
terminals
C T V F=0, f=1MHz, Ta=25°C ― 45 ― pF
V F=1.0, V O=5.5V ―― 250 High level output current I OH
V F=1.0, V O=5.5V, Ta=25°C ― 0.5 10
μA
Low level output voltage V OL I F=10mA
I OL=13mA(sinking)
― 0.4 0.6 V
心态的英文"H level output→ L level output" input current I FH
I OL=13mA(sinking)
V OL=0.6V
―― 10 mA
High level supply current I CCH V CC=5.5V, I F=0 ― 7 15 mA Low level supply current I CCL V CC=5.5V, I F=16mA ― 12 18 mA
Input−output
insulation leakage current
I S
V S=3540V, t=5s
Ta
=
25°C (Note
4)
―― 100 μA
Isolation resistance R S R.H. ≤ 60%, V S=500V DC
Ta=25℃ (Note
4)
5×1010 1014―Ω
Stray capacitance between input to output C S
V S=0, f=1MHz
中试生产Ta=25℃ (Note
4)
― 0.8 ― pF
* All typical values are V CC=5V, Ta=25°C
Switching Characteristics (V CC =5V, Ta=25°C)
Characteristic Symbol Test
Cir −
cuit
Test Condition
Min.
Typ.
Max.
Unit
Propagation delay time (H →L)
t p HL 1
I F =0→16mA
C L =15pF, R L =350Ω ― 60 120 ns
Propagation delay time (L →H)
t p LH 1
I F =16→0mA
C L =15pF, R L =350Ω ― 60 120 ns
Output ri −fall time (10−90%)
t r , t f 2
R L =350Ω, C L =15pF
I F =016mA ― 30 ― ns
Common mode transient imunity at high output level
CM H 2
I F =0mA, V CM =200V p −p
V O(min)=2V, R L =350Ω
― 200 ― V / μs
Common mode transient imunity at low output level
CM L 2 I F =16mA, V CM =200V p −p
V O(max)=0.8V,
R L =350Ω
― −500 ― V / μs
(Note 4) Device considered a two −terminal device: Pins 1 and 3 shorted together, and pins 4, 5 and 6 shorted
together. (Note 5) The V CC supply voltage to each TLP113 isolator must be bypasd by 0.1μF capacitor, this can be either a
ceramic or solid tantalum capacitor with good high frequency characteristic and should be connected as clo as possible to package V CC and GND pins of each device. (Note 6) Maximum electrostatic discharge voltage for any pins: 180V(C=200pF, R=0)
Test Circuit 1: Switching Time Test Circuit
C L is approximately 15pF which includes probe and stray wiring capacitance.
Test Circuit 2: Common Mode Transient Immunity Test Circuit
s)μ(f t 160(V)=
L C Μs)
μ(r t 160(V)
=
ΗC Μ,
C L is approximately 15pF which includes probe and stray wiring capacitance.
0.5V
I V O V CC = 5V
Pul input PW = 100μs
脸谱怎么画
I F monitor
200V
0V V OL
V O
V V O V CC = 5V
Z O = 50Ω
V O
(I F (I F
