Reference number ISO 22716:2007(E)
INTERNATIONAL STANDARD ISO 22716
First edition 2007-11-15
美丽的乡村
Cosmetics — Good Manufacturing
Practices (GMP) — Guidelines on Good Manufacturing Practices
Cosmétiques — Bonnes Pratiques de Fabrication (BPF) — Lignes directrices relatives aux Bonnes Pratiques de Fabrication
--``,,``,,``,,`,``,``,`,,,,`,,`-`-`,,`,,`,`,,`---勿失勿忘
ISO 22716:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licend to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products ud to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for u by ISO member bodies. In the unlikely event that a problem relating to it is found, plea inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2007
All rights rerved. Unless otherwi specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office
Ca postale 56 • CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyright@iso Web www.iso Published in Switzerland
--``,,``,,``,,`,``,``,`,,,,`,,`-`-`,,`,,`,`,,`---
ISO 22716:2007(E)
Contents Page
Foreword (iv)
Introduction (v)
1Scope (1)
2Terms and definitions (1)
劳动人事3Personnel (4)
4Premis (6)
5Equipment (8)
高考加油文案
6Raw materials and packaging materials (10)
7Production (11)塞优
8Finished products (14)
9Quality control laboratory (15)
10Treatment of product that is out of specification (17)
尊师重教11Wastes (17)
12Subcontracting (18)windows壁纸
13Deviations (19)
翻译英语怎么说14Complaints and recalls (19)
15Change control (19)
16Internal audit (20)
17Documentation (20)
--``,,``,,``,,`,``,``,`,,,,`,,`-`-`,,`,,`,`,,`---
ISO 22716:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be reprented on that committee. Interna
tional organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates cloly with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 22716 was prepared by Technical Committee ISO/TC 217, Cosmetics.
ISO 22716:2007(E)
Introduction
The guidelines are intended to provide guidance regarding Good Manufacturing Practices for cosmetic products. The guidelines have been prepared for consideration by the cosmetic industry and take into account the specific needs of this ctor. The guidelines offer organizational and practical advice on the management of the human, technical and administrative factors affecting product quality.
The guidelines have been written to allow them to be ud following the flow of products from receipt to shipment. Additionally, in order to clarify the way this document reaches its objectives, a ‘principle’ is added to each major ction.
Good Manufacturing Practices constitute the practical development of the quality assurance concept through the description of the plant activities that are bad on sound scientific judgement and risk asssments. The objective of the GMP guidelines is to define the activities that enable you to obtain a product that meets defined characteristics.
Documentation is an integral part of Good Manufacturing Practices.
--``,,``,,``,,`,``,``,`,,,,`,,`-`-`,,`,,`,`,,`---
