商贾Emergency stop SW pccurred.元件废弃异常。Failed in the Lar recog angle error.激光识别角度发生异常。R1-Head failed to relea component.在R1-Head中，带回了贴片元件。The gotten nozzle width does not meet that of le.测定的吸嘴宽度与设置的吸嘴宽度不一致。Feeder Flow Seneor detected.E051001
netlimiterE109132
E109134
狼的启示The part abandonment is abnormal.Error was detected in checking if any nozzles attached.E242508
E249001
E291004
Axis movement error (Z axis driver error)轴浮动错误。（Z轴驱动错误）The origin point return is non-completion,plea operate again after compe E109220
检查吸嘴安装，发生错误。Return to home not yet been completed.没有执行返回原点。Failde to originate,becau of Feeder-Floating.Plea retry.因传送带浮动，返回原点失败，请再次执行。Failde t
o detect the home of Theta-axis,plea retry origination.因为查出θ轴原点错误，返回原点失败，请再次执行。E500302
E500602
规章
E501999
E509606
E301028
E301012
E301015
E541502
E610026
E610200
E611030
E509701
E520021
E520108
E541132
关于父母爱的名言
E615065
E616049发生紧急停止。Nozzles can not be detected.没有发现吸嘴。An error occurred when detecting the lar dirt(R1-head).查出了传送带浮动传感器。无元件。No component.吸取位置偏差。Pick position check error.激光检查是否干净。Lar nsor maight be dirty.Plea clean the nsor.
气压下降。Air was down.吸嘴尺寸过短，请检查吸嘴。Length of the nozzle is too short,plea check the nozzle.异常结束生产。Abnormal stop.废弃元件发生错误。An error occurred when disposing a component.吸嘴过长，请检查吸嘴。Nozzle length is too long.Plea check out the nozzle.激光测定吸嘴高度发生错误。没有执行返回原点，请执行返回原点后，再次操作。The conveyor becau a time-out.Execution is laborted.传送超时，停止运行。An error occurred while measuring nozzle height by laster.
Q323000Q323001E616049E650227E650237E652250E652651是否重置I/O？
基板传送错误，入口缓冲器和中心缓冲器间的基板移动由于超时而结束了。
Conveyor error:Time out error terminates PWB ejecting to next process.基板传送错误：对后工序的基板搬出动作由于超时而结束了。
Exit manual control.Ret I/O?
人贵自知传送基板错误，入口传感器超时。
歌声与微笑吉他谱PWB Conveying Error:STOP nsor ON detection error at Center Stopper ON.传送基板错误，中心STOP ON时，发现STOP传感器ON错误。
Conveyor error:Time out terminates PWB transportation between IN buffer an 退出手动控制，是否进行各I/O的安全方向设定？
great最高级Ret I/O?
激光传感器弄脏，请把传感器擦干净。
PWB Conveying Error:Timeout in detecting IN nsor's turning OFF.
competing the origin point return.
ON.
er and Center buffer. .
