编号 | 中文名称 | 英文名称 |
ANSI Z136.1 Errata-1993 | 服装商标激光的安全使用.勘误表 | Safe u of lars; Errata |
ANSI Z136.1-2000 | 激光器的安全使用 | Safe U of Lars |
ANSI Z136.2-1997 | 激光二极管和LED光源的光纤通信系统的安全使用 | Safe U of Optical Fiber Communication Systems Utilizing Lar Diode and LED Sources |
ANSI Z136.3-2005 | 保健设施中激光器的安全使用 | Safe U of Lars in Health Care Facilities |
ANSI Z136.4-2005 | 危害评定用激光器安全测量的美国国家标准推荐实施规程 | American National Standard Recommended Practice for Lar Safety Measurements for Hazard Evaluation |
ANSI Z136.5-2000 | 教育机构中激光设备的安全使用验电器原理 | Safe U of Lars in Educational Institutions |
ANSI Z136.6-2005 | 户外激光器的安全使用 | Safe U of Lars Outdoors |
ANSI/ASME B89.4.19-2006 | 基于球形坐标测量系统的激光器性能评价 | Performance Evaluation of Lar Bad Spherical Coordinate Measurement Systems |
ANSI/AWS C7.2-1998 | 激光束焊接、切割和打孔推荐规程 | Recommended Practices for Lar Beam Welding, Cutting, and Drilling |
大学校园活动ANSI/EIA/TIA 455-127-1991 | 多模激光器的光谱特征 | Spectral Characterization of Multimode Lars |
ANSI/EIA/TIA 455-48B-1990 | 光纤包覆层直径的激光类仪器测量 | Measurement of Optical Fiber Cladding Diameter Using Lar-Bad Instruments |
ANSI/NFPA 115-2003 | 激光器防火措施 | Lar Fire Protection |
ANSI/TIA-455-130-2001 | 激光二极管的高温寿命试验 | Elevated Temperature Life Test for Lar Diodes |
ANSI/TIA-455-48B-1990 父母是孩子最好的榜样 | 利用激光仪器测量光纤包覆层直径 | Measurement of Optical Fiber Cladding Diameter Using Lar-Bad Instruments |
ANSI/TIA-568-B.1-4-2003 | 商用建筑电信电缆敷设标准.第1部分:一般要求.补充件4. 第6类850nm激光优选的50/125微米多模纤维的鉴别 | Commercial Building Telecommunications Cabling Standard - Part 1: General Requirements - Addendum 4 - Recognition of Category 6 and 850 nm lar-Optimized 50/125 Micron Multi-mode Fiber |
ANSI/TIA/EIA 455-128-1996 | 半导体激光器阈值电流的测定程序 | Procedures for Determining Threshold Current of Semiconductor Lars |
ANSI/TIA/EIA 455-130-2001 | 激光二极管的抗高温寿命试验 | Elevated Temperature Life Test for Lar Diodes |
ANSI/TIA/EIA 455-48B-1990 | 用激光测量仪测量光纤连皮直径 | 岁岁有今朝Measurement of Optical Fiber Cladding Diameter Using Lar-Bad Instruments |
ANSI/TIA/EIA 568-B.1-4-2003 | 商用建筑电信电缆敷设标准.第1部分:一般要求.附录4.类别6、850nm激光优选50/125微米多模纤维 | Commercial Building Telecommunications Cabling Standard - Part 1: General Requirements - Addendum 4 - Recognition of Category 6 and 850 nm lar-Optimized 50/125 Micron Multi-mode Fiber |
ASTM A 1006/A 1006M-2000 | 激光束焊、平头、无镀层、钢制总管的标准规范 | Standard Specification for Steel Line Pipe, Black, Plain End, Lar Beam Welded |
ASTM C 1070-1986 | 用激光扩散法测定氧化铝和石英粒度分布的试验方法 | Test Method for Determining Particle Size Distribution of Alumina or Quartz by Lar Light Scattering |
ASTM D 3460-1998 | 有白色水印和无水印的票据、油印机、复印机、复照和激光打印机用按尺寸切割的办公用纸的标准规范 | Standard Specification for White Watermarked and Unwatermarked Bond, Mimeo, Spirit Duplicator, Reprographic, and Lar Printer Cut-Sized Office Papers |
ASTM D 4464-2000 | 激光散射测定催化材料粒度分布的标准试验方法 | Standard Test Method for Particle Size Distribution of Catalytic Material by Lar Light Scattering |
ASTM D 5174-2002 | 用脉冲激光磷光光度法测定水中微量铀的标准试验方法 | Standard Test Method for Trace Uranium in Water by Puld-Lar Phosphorimetry |
ASTM D 6187-1997 | 带有氮激光感应荧光的石油污染位点的锥形透度计技术特性的标准操作规程 | Standard Practice for Cone Penetrometer Technology Characterization of Petroleum Contaminated Sites with Nitrogen Lar-Induced Fluorescence |
ASTM D 6466-1999 | 用Sirolan激光扫描纤维直径分析仪测定羊毛和其它动物纤维直径的标准试验方法 | Standard Test Method for Diameter of Wool and Other Animal Fibers By Sirolan-Larscan Fiber Diameter Analyr |
ASTM D 7134-2005 | 教练传奇用矩阵辅助激光解吸/离子化(MALDI)-飞行时间(TOF)质谱(MS)法测定无规立构聚苯乙烯的平均分子量和分子量分布 | Standard Test Method for Molecular Mass Averages and Molecular Mass Distribution of Atactic Polystyrene by Matrix Assisted Lar Desorption/Ionization (MALDI)-Time of Flight (TOF) Mass Spectrometry (MS) |
ASTM D 7153-2005 | 航空燃料冻结点的标准试验方法(自动激光法) | Standard Test Method for Freezing Point of Aviation Fuels (Automatic Lar Method) |
ASTM E 1458-1992 | 用光掩模原版校准检验激光绕射粒子定尺寸仪器的试验方法 | Test Method for Calibration Verification of Lar Diffraction Particle Sizing Instruments Using Photomask Reticles |
ASTM F 1364-2003 | 使用校准设备验证干涉激光成像无损轮胎检验系统检验能力的标准实施规范 | Standard Practice for U of a Calibration Device to Demonstrate the Inspection Capability of an Interferometric Lar Imaging Nondestructive Tire Inspection System |
ASTM F 1457-1994 | 与激光打印机相关的术语 | Standard Terminology Relating to Lar Printers |
ASTM F 1457b-1994 | 与激光打印机相关的标准术语 | Standard Termninology Relating to Lar Printers |
ASTM F 1497a-1999 | 导管轴耐激光性能测定的标准试验方法 | Standard Test Method for Determining Lar Resistance of the Shaft of Tracheal Tubes |
ASTM F 1628-1995 | 给对象说的情话激光外科学用套箍和未套箍气管导管及有关治疗的标记和标志的标准规范 | Standard Specification for Labeling and Marking of Cuffed and Uncuffed Tracheal Tubes and Related Treatments Intended for U During Lar Surgery |
IEEE 647-1995 | 单轴激光陀螺规格导则和试验规程 | (Format guide and test procedure for single-axis lar gyros) |
编号 | 中文名称 | |
本文发布于:2023-07-16 13:23:22，感谢您对本站的认可！
本文链接：https://www.wtabcd.cn/fanwen/fan/89/1083784.html
版权声明：本站内容均来自互联网，仅供演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系，我们将在24小时内删除。
| 留言与评论（共有 0 条评论） |
