千门万户瞳瞳日80xx systems
For all operating environments
Hot-swapping a power supply
Hot-swapping a power supply involves turning off, disconnecting, and removing the old power supply and installing,
connecting, and turning on the replacement power supply.
Before you begin
All other components in the system must be functioning properly; if not, you must contact technical support.
About this task
•The power supplies are redundant and hot-swappable.
To prevent system downtime, you must replace only one power supply at a time.
Note: Power supplies are auto-ranging.
Steps
1. Removing a power supply on page 1
2. Installing a power supply on page 4
行测题型及答题技巧3. Completing the replacement process on page 4
Removing a power supply
To remove a power supply, you must identify the one you want to remove, disconnect the power cord, and remove the power supply from the chassis.
About this task
Attention: You should replace the power supply within two minutes of removing it from the chassis. The system continues to function, but Data ONTAP nds messages to the console about the degraded power supply until the power supply is
replaced.
Steps
1. Identify the power supply you want to replace, bad on console error messages or through the LEDs on the power supplies.
See the Hardware Platform Monitoring Guide for a description of LED behaviors.
8020 PSU locations
215-08008_B0August 2015Copyright © 2015 NetApp, Inc. All rights rerved.
1
Web: • Feedback:
1
2
Other 80xx PSU locations
辉煌的意思是什么2. If you are not already grounded, properly ground yourlf.
3. Turn off the target power supply and remove the power cord by completing the following substeps, using the illustration for
reference:
2Hot-swapping a power supply
a. Pinch the tab on the locking mechanism of the cable retainer clip, and then open the retainer clip.
b. Slide the retainer clip off the cord.
c. Unplug the power cord from the power supply and the power source.
4. Press down the relea latch on the power supply cam handle, lower the cam handle to the fully open position, and then slide
the power supply out of the chassis.
Make sure that you support the power supply with your free hand.
Removing a power supply3
Installing a power supply
关于月季花的作文To install a power supply, you must place the power supply in the chassis, cure it, and reconnect the power cord to the power source.
Steps
1. Make sure that the on/off switch of the new power supply is in the Off position.
2. If you are not already grounded, properly ground yourlf.
3. Inrt the replacement power supply into the chassis by aligning it with the opening and gently pushing the power supply
into the chassis.
藤艺家具Attention: The power supplies are keyed and can only be installed one way.
玫瑰花含义
4. Push firmly on the power supply cam handle to at it all the way into the chassis, and then push the cam handle to the
clod position, making sure that the cam handle relea latch clicks into its locked position.
5. Reconnect the power cord and cure it to the power supply using the cable retaining clip.
6. Reconnect the power supply to the power source, and then turn it on.
The power supply should run with no fault LEDs lit and the green LED lit.
Completing the replacement process
After you replace the part, you can return the failed part to NetApp, as described in the RMA instructions shipped with the kit.
Contact technical support at NetApp Support, 888-463-8277 (North America), 00-800-44-638277 (Europe), or
+800-800-80-800 (Asia/Pacific) if you need the RMA number or additional help with the replacement procedure. Copyright information
Copyright © 1994–2015 NetApp, Inc. All rights rerved. Printed in the U.S.
幼儿涂色No part of this document covered by copyright may be reproduced in any form or by any means—graphic, electronic, or
mechanical, including photocopying, recording, taping, or storage in an electronic retrieval system—without prior written permission of the copyright owner.
Software derived from copyrighted NetApp material is subject to the following licen and disclaimer:
THIS SOFTW ARE IS PROVIDED BY NETAPP "AS IS" AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED W ARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE HEREBY DISCLAIMED. IN NO EVENT SHALL NETAPP BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIA
BILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTW ARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
NetApp rerves the right to change any products described herein at any time, and without notice. NetApp assumes no
responsibility or liability arising from the u of products described herein, except as expressly agreed to in writing by NetApp.
The u or purcha of this product does not convey a licen under any patent rights, trademark rights, or any other intellectual property rights of NetApp.
The product described in this manual may be protected by one or more U.S. patents, foreign patents, or pending applications.
4Hot-swapping a power supply
RESTRICTED RIGHTS LEGEND: U, duplication, or disclosure by the government is subject to restrictions as t forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Softw
are clau at DFARS 252.277-7103 (October 1988) and FAR 52-227-19 (June 1987).
Trademark information
NetApp, the NetApp logo, Go Further, Faster, AltaVault, ASUP, AutoSupport, Campaign Express, Cloud ONTAP, Clustered Data ONTAP, Customer Fitness, Data ONTAP, DataMotion, Fitness, Flash Accel, Flash Cache, Flash Pool, FlashRay,
FlexArray, FlexCache, FlexClone, FlexPod, FlexScale, FlexShare, FlexV ol, FPolicy, GetSuccessful, LockVault, Manage
ONTAP, Mars, MetroCluster, MultiStore, NetApp Insight, OnCommand, ONTAP, ONTAPI, RAID DP, RAID-TEC, SANtricity, SecureShare, Simplicity, Simulate ONTAP, Snap Creator, SnapCenter, SnapCopy, SnapDrive, SnapIntegrator, SnapLock, SnapManager, SnapMirror, SnapMover, SnapProtect, SnapRestore, Snapshot, SnapValidator, SnapVault, StorageGRID, Tech OnTap, Unbound Cloud, and W AFL and other names are trademarks or registered trademarks of NetApp, Inc., in the United States, and/or other countries. All other brands or products are trademarks or registered trademarks of their respective holders and should be treated as such. A current list of NetApp trademarks is available on the web /us/legal/ netapptmlist.aspx.
兰州市住房公积金
How to nd comments about documentation and receive update notifications
You can help us to improve the quality of our documentation by nding us your feedback. You can receive automatic
notification when production-level (GA/FCS) documentation is initially relead or important changes are made to existing production-level documents.
If you have suggestions for improving this document, nd us your comments by email to To help us direct your comments to the correct division, include in the subject line the product name, version, and operating system.
If you want to be notified automatically when production-level documentation is relead or important changes are made to existing production-level documents, follow Twitter account @NetAppDoc.
You can also contact us in the following ways:
•NetApp, Inc., 495 East Java Drive, Sunnyvale, CA 94089 U.S.
•Telephone: +1 (408) 822-6000
•Fax: +1 (408) 822-4501
•Support telephone: +1 (888) 463-8277
Trademark information5
