DISASSEMBLY
1.Regulator can be disasmbled without removal from air line.
2.Shut off inlet pressure. Reduce pressure in inlet and outlet lines to zero.
3.Turn adjustment (2 or 5A) fully counterclockwi to remove all force on regulating spring (6).
4.Disasmble in general accordance with the item numbers on exploded view.
大而无当CLEANING
1.Clean parts with warm water and soap.
2.Rin and dry parts. Blow out internal passages in body with clean, dry compresd air.
3.Inspect parts. Replace tho found to be damaged.ASSEMBLY
1.Lubricate als and o-rings with o-ring grea.
2.Asmble the unit as shown on the exploded view.
3.Torque Table
TORQUE
ITEM NM (INCH-POUNDS)2, 5A (Bonnet)7,34 to 8,47 (65 to 75)9 (Early valve at)0,45 to 0,68 (4 to 6)†11 (Current valve at)0,34 to 0,56 (3 to 5)††Diaphragm pin (8) must slide freely thru valve at after torquing.
WARNING
The products are intended for u in industrial
compresd air systems only. Do not u the products where pressures and temperatures can exceed tho listed under Technical Data .
If outlet pressure in excess of the regulator pressure tting could cau downstream equipment to rupture or malfunction, install a pressure relief device downstream of the regulator. The relief pressure and flow capacity of the relief device must satisfy system requirements.
超魔神胡帕The accuracy of the indication of pressure gauges can change, both during shipment (despite care i
n packaging)and during the rvice life. If a pressure gauge is to be ud with the products and if inaccurate indications may be hazardous to personnel or property, the gauge should be calibrated before initial installation and at regular intervals during u.
Before using the products with fluids other than air, for non industrial applications, or for life-support systems consult Norgren.
fighting是什么意思TECHNICAL DATA Fluid: Compresd air
Maximum pressure: 20 bar (300 psig)
卫玠读音Operating temperature*: -34°to +65°C (-30°to +150°F)*Air supply must be dry enough to avoid ice formation at temperatures below +2°C (+35°F).
Typical flow with 10 bar (150 psig) inlet pressure, 6,3 bar
二的英文怎么写(90 psig) t pressure and 1 bar (15 psig) droop from t:
1/8" Ports: 6,5 dm 3/s (14 scfm)1/4" Ports: 7 dm 3/s (15 scfm)Gauge ports:
1⁄8 PTF with PTF main ports Rc1/8 with ISO Rc main ports Rc1/8 with ISO G main ports Materials:Body: Zinc Bonnet : Acetal Valve: Brass/nitrile Valve at: Acetal Elastomers: Nitrile
REPLACEMENT ITEMS
Service kit (includes items circled on exploded view)
<3407-01Tamper 18-001-092PANEL MOUNTING DIMENSIONS
Panel mounting hole diameter: 30 mm (1.19")Panel thickness: 2 to 6 mm (0.06" to 0.25")
INSTALLATION
1.Shut off air pressure. Install regulator in air line -G with air flow in direction of arrow on body,G upstream of lubricators and cycling valves.
G as clo as possible to the device being rviced.G at any angle.
2.Connect piping to proper ports using pipe thread alant on male threads only. Do not allow alant to enter interior of regulator.
烤地瓜空气炸锅3.Install a pressure gauge or plug the gauge ports. Gauge ports can also be ud as additional outlets for regulated air.
4.Install a Norgren general purpo filter upstream of the regulator.
ADJUSTMENT
1.Before applying inlet pressure to regulator, turn
adjustment (2 or 5A) counterclockwi to remove all force on regulating spring (6).
2.Apply inlet pressure, then turn adjustment clockwi to increa and counterclockwi to decrea pressure tting.
3.Always approach the desired pressure from a lower pressure. When reducing from a higher to a lower tting, first reduce to some pressure less than that desired, then bring up to the desired pressure.
NOTE
With non-relieving regulators, make pressure reductions with some air flow in the system. If made under no flow (dead-end) conditions, the regulator will trap the over-pressure in the downstream line.
4.Push adjusting knob down to lock pressure tting; pull up to relea. Install tamper resistant knob (e
Replacement Items ) to make tting tamper resistant.
* Outlet pressure can be adjusted to pressures in excess of, and less than, tho specified. Do not u the units to control pressures outside of the specified PTF
galaxy<1/8"
<1/4"
<0,1 to 0,7 bar (1 to 10 0,3 to 3,5 bar (5 to 50 0,3 to 7 bar (5 to 100 psig)
小零食做法G....Without
