ABS AF312B
Injection Molding Grade
Description
Application
Flame Retardant, TBBA
Electric parts, IT/OA device TV, monitor housing
行政是干嘛的
喜欢一个人什么感觉
Test Condition Test Method
Unit
Typical Value
清蒸鱼做法Physical
倒插门什么意思Specific Gravity
ASTM D792- 1.18Molding Shrinkage (Flow), 3.2mm ASTM D955%0.4~0.7Melt Flow Rate
220℃/10kg
ASTM D1238g/10min 60
Mechanical
Tensile Strength, 3.2mm ASTM D638
@ Yield
50mm/min
kg/cm 2
440
Tensile Elongation, 3.2mm ASTM D638
@ Yield 50mm/min %5@ Break
50mm/min %
20Tensile Modulus, 3.2mm 1mm/min ASTM D638kg/cm 222,000Flexural Strength, 6.4mm 15mm/min ASTM D790kg/cm 2690Flexural Modulus, 6.4mm
15mm/min ASTM D790kg/cm 225,000IZOD Impact Strength, 6.4mm ASTM D256
(Notched)
23℃kg·cm/cm 24-30℃
kg·cm/cm
8
IZOD Impact Strength, 3.2mm ASTM D256
(Notched)
23℃kg·cm/cm 27-30℃kg·cm/cm
8Rockwell Hardness胡寿根
R-Scale
ASTM D785
-104
Thermal
Heat Deflection Temperature, 6.4mm ASTM D648
(Unannealed)
18.6kg ℃764.6kg
℃
84
Vicat Softening Temperature
ASTM D1525
5kg, 50℃/h ℃84
1kg, 120℃/h
℃
Flammability UL94
1.0mm class V-2
2.1mm class V-0,5VB 2.5mm class V-0,5VA
3.0mm
class
V-0,5VA
Relative Temperature Index UL 746B
Electrical
℃75Mechanical with Impact ℃70Mechanical without Impact
℃
75Note) Typical values are only for material lection purpo, and variation within normal tolerances are for various colors. Values given should not be interpreted as specification and not be ud for part or tool design.
All properties, except melt flow rate are measured on injection molulded specimens and after 48 hours storage at 23℃, 50% relative humidty.
Updated :1-Jul-14
The information contained herein,including,but not limited to,data,statements and typical values,are given in good faith.LG Chem makes no warranty or guarantee,expresd or implied,(i)that the result described herein will be obtained under end -u conditions,or (ii)as to the effectiveness or safety of any design incorporating LG Chem materials,products,recommendations or advice.Further,any information contained herein shall not be construed as a part of legally binding offer.Especially,the typical values should be regarded as reference values only and not as binding minimum values.Each ur bear full responsibility for making its own determination as to the suitability of LG Chem's materials,products,recommendations,or advice for its own particular u.Each ur must identify and perform all tests and analys necessary to assure that its finished parts incorporating LG Chem material or products will be safe and suitable for u under end -u conditions.The data contained herein can be changed without notice as a result of the quality improvement of the products.
Properties
ABS AF312B
Injection Molding Grade
Unit
Value
℃70 ~ 80hrs 2 ~ 4Minimum Moisture Content %0.01℃200 ~ 230Rear ℃170 ~ 190Middle ℃180 ~ 200Front
℃190 ~ 210℃200 ~ 230℃40 ~ 60Back Pressure kg/cm 2 5 ~ 10rpm
30 ~ 60
Note) Back Pressure & Screw Speed are only mentioned as general guidelines.
The may not apply or need adjustment in specific situations such as low shot sizes, thin wall molding and gas-assist molding.
Unit
Value
℃hrs Minimum Moisture Content %℃Zone 1℃Zone 2℃Zone 3℃Zone 4
℃℃℃Top ℃Middle ℃Bottom ℃
Note) Recommend initial lower temperatures ttings to avoid material degradation/hang-up in die & purge material from extruder prior to shutdown.
徐志摩的偶然Updated :1-Jul-14
The information contained herein,including,but not limited to,data,statements and typical values,are given in good faith.LG Chem makes no warranty or guarantee,expresd or implied,(i)that the result described herein will be obtained under end -u conditions,or (ii)as to the effectiveness or safety of any design incorporating LG Chem materials,products,recommendations or advice.Further,any infor
mation contained herein shall not be construed as a part of legally binding offer.Especially,the typical values should be regarded as reference values only and not as binding minimum values.Each ur bear full responsibility for making its own determination as to the suitability of LG Chem's materials,products,recommendations,or advice for its own particular u.Each ur must identify and perform all tests and analys necessary to assure that its finished parts incorporating LG Chem material or products will be safe and suitable for u under end -u conditions.The data contained herein can be changed without notice as a result of the quality improvement of the products.
Drying Time
龙骨的功效
Roll Stack Tempeature
Drying Time
Nozzle Temperature Adapter Temperature Melt Temperature Barrel Temperature Drying Temperature Melt Temperature Mold Temperature Screw Speed
Die Temperature Processing Parameters
卫嬿婉结局Processing Parameters
Cylinder Temperature Drying Temperature
