ISO5832-1第一部分 Wrought stainless steel 锻造不锈钢

更新时间:2023-06-30 19:12:34 阅读: 评论:0

ISO5832-1第一部分 Wrought stainless steel 锻造不锈钢
1、范围 Scope
ISO5832这部分对用锻造不锈钢制造的外科植入物指定了相对应的特定的测试方法。
this part of iso5832 specifies the characteristics of,and corresponding test methods for,wrought stainless steel for u in the manufacture of surgical implants.
提供最适宜的两种类型的不锈钢化学基础成分(见表1)
Provision is made for two types of stainless steel bad on chemical composition(e table 1)
NOTE 1 用使用本标准材料加工的最终产品的试样的力学性能不必完全与本标准规定的指标相同。
NOTE 2
2、规范性引用文件 normative references
下列文件中的条款通过本标准的引用而成为本标准的条款。凡是注日提的引用文件,其随后的所有的修改修订版本均不适于本标准,但是,为了鼓励根据本标准达成协议的各方的研究,凡是没有注明日期的引用文件,其最新版本均适用于本标准。
ISO 377  Steel and steel products-Location and preparation of samples and test pieces for mechanical testing.
ISO 404……………………..
3、化学成分  chemical composition
3.1 试验样本 test samples
用于分析的样品应符合ISO 377规定。
The lection of samples for analysis shall be carried out in accordance with ISO 377.
3.2 铸造分析 Cast analysis
    刚的化学成分应符合表1的规定。Cr含量和Mo含量按照下列公式计算所得(C值)应该不小于26。
The cast analysis of the steel when determined in accordance with clau 6 shall comply with the chemical composition specified in table1.The molybdenum and chromium contents shall be such that the C value obtained from the formula given below is not less than 26.
C=3.3WMo+WCr
其中:
WMo 钼的含量,用质量百分比表示;
WCr 铬的含量,用质量百分比表示。
表1—化学成分
元素
质量百分比 %
0.03≦
1.0≦
2.0≦
0.025≦
0.01≦
0.1≦
17.0~19.0
2.25~3.50
13.0~15.0
0.50≦
余量
4、微观条件下的完全退火 microstructure in the fully annealed condition
4.1 晶粒度 grain size
奥氏体的晶粒度按照第六条规定不得大于5级。
the austenitic grain size,determined in accordance with clau6,shall not be coarr than grain size No.5.
4.2 微观结构 microstructure
根据条款6进行检测时,此不锈钢应不含δ铁素体、X相或者Σ相。
the steel shall have a structure free from delta ferrite,chi or sigma pha,when examined in accordance with Clau 6.
4.3非金属夹杂物含量 inclusion content
钢铁应该检验非金属夹杂物的含量,在热轧阶段完成尺寸定型以后应该与第六条的规定相一致,不得超过表2的规定。
the non-metallic inclusion content of the steel,determined at finished size after a hot-rolling process stage,and in accordance with Clau 6,shall not exceed the limits given in Table 2.
注意:有必要符合真空或者电渣冶炼法清洁条件规定。
Note:it can be necessary to u vacuum or electroslag melting to produce a steel complying with the cleanliness requirements.
表2— 夹杂物规定
Table 2 — inclusion content limits
Type of  inclusion
夹杂物类型
Inclusion  content  reference  number
夹杂物级别
Thin
细系列
和好的意思
Thick
粗系列
A
1.5
1
B
1.5
1
C
1.5
1
D
1.5
1
5 力学性能 Mechanical properties
5.1 试样 test pieces
选择的样品和拉伸试件应该符合ISO 377的规定。
the lection and preparation of samples and test pieces for tensile shall be in accordance with ISO 377.
5.2拉伸试验 Tensile test
钢在棒材、丝材、板材、带材形式下的拉伸性能实验应该与条款六相一致,必须分别符合表3、5、6的规定。
the tensile properties of the steel in the form of bars,wires,and sheet and strip,when tested in accordance with Clau 6,shall comply with the values specified in Tables 3,5 and 6 respectively.
5.3 标记长度  gauge  length
S0指的是试样的原始横截面积单位mm。试样的直径d1或者横截面S0,分别应符合,标记长度应该为5.65× or 50 mm(见表4或表7)。
S0 is defined as the original cross-ctional area in square millimetres. in accordance with test piece diameter,D1 or ction profile,S0,respectively,the gauge length shall be either 5.65× or 50 mm(e table 4 and table 7).
6 实验方法 Test methods
用于确定ISO5832 本部分的规定的测试方法应该符合表8所列的要求。
the test methods to be ud in determining compliance with the requirements of this part of ISO 5832 shall be tho given in table 8.
表3 — 钢棒的力学性能
Condition
状态
Diameter or thickness
直径或者厚度
d
mm
Tensile strength
拉伸强度
Rm
MPa
0.2% proof stress of
non-proportional elongarion
0.2%的非比例伸长应力
Rp0.2min
MPa
Elongarion after fracture/Gauge length
折断后的伸长率/标记长度
Amin
%
退火的
全部
490≦Rm大学请假的好理由≦690
190
40
冷加工
≦22
860≦Rm≦1100
390
12
超硬
≦8
劳动人民图片
≦1400
——
——
表4 — 标记长度和产品之间的对应
Table 4 — Correspondence between gauge length and product
Product
产品
Gauge length
标记长度
50 mm
5.65×
Round bar,wires
圆钢,钢丝
d﹥5mm
d≦5mm
Sections,profiles
截面,轮廓面
S0﹥40mm2
S0≦40mm2
Table 5 — Mechanical properties of wires
表5 — 钢丝的力学性能
状态
直径
d mm
抗拉强度
Rm MPa
折断后的伸长率/标记长度
A语病的六大类型min %
退火
0.025≦d≦0.13
≦1000
30
0.13﹤d≦0.23
≦930
30
0.23﹤d≦0.38
≦890
35
0.38﹤d≦0.5
≦860
40
0.5﹤d≦0.65
≦820
40梦见和女人吵架
d﹥0.65
≦800
40
冷拔
0.2≦d≦0.7
1600≦Rm≦1850
——
0.7﹤d≦1.0
1500≦Rm≦1750
——
1.0﹤d≦1.5
1400≦Rm≦1650
——
1.5﹤d≦2.0
1350≦Rm≦1600
——
冷拉状态下订货的钢丝,可按照需方的更高强度等级供货,力学性能指标有供需双方协商确定。
Table 6 — Mechanical properties of strip and sheet
图书馆计划
Condition
状态
Tensile strength
拉伸强度
Rm
MPa
0.2% proof stress of
non-proportional elongarion
0.2%的非比例伸长应力
Rp0.2min
MPa
Elongarion after fracture/Gauge length
折断后的伸长率/标记长度
Amin
%皇冠箱包
退火的
490≦Rm≦690
190
40
物流公司简介
冷加工
860≦Rm≦1100
690
10
表6 — 带材和板材的力学性能
Table 7 — Correspondence between gauge length and thickness of the product

本文发布于:2023-06-30 19:12:34,感谢您对本站的认可!

本文链接:https://www.wtabcd.cn/fanwen/fan/89/1061984.html

版权声明:本站内容均来自互联网,仅供演示用,请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系,我们将在24小时内删除。

标签:应该   规定   符合   不锈钢   拉伸   标准
相关文章
留言与评论(共有 0 条评论)
   
验证码:
推荐文章
排行榜
Copyright ©2019-2022 Comsenz Inc.Powered by © 专利检索| 网站地图