一、入水：gate
进入位：gate location 水口形式：gate type
大水口：edge gate 细水口：pin-point gate
水口大小：gate size 转水口：switching runner/gate
唧嘴口径：sprue diameter
二、流道: runner
热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner
给家长的一封信流道电脑分析：mold flow analysis 流道平衡:runner balance
热嘴：hot sprue 热流道板：hot manifold
邓晓辉
发热管：cartridge heater 探针: thermocouples
插头：connector plug 插座：connector socket 密封/封料：al 三、运水：water line
喉塞：line plug 喉管：tube
塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker
四、模具零件：mold components
三板模：3-plate mold 二板模：2-plate mold
边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing
中托司：shoulder guide bushing 中托边L：guide pin
顶针板：ejector retainner plate 托板：support plate
螺丝：screw 管钉：dowel pin 开模槽：ply bar scot
内模管位：core/cavity inter-lock 顶针：ejector pin
司筒：ejector sleeve 司筒针：ejector pin
吴亦凡歌曲
韩庚演的电影推板：stripper plate 缩呵：movable core,return core core puller
扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter
模胚（架）：mold ba 上内模：cavity inrt
下内模：core inrt 行位（滑块）：slide
镶件：inrt 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴：sprue bushing
挡板：stop plate 定位圈：locating ring 锁扣：latch
扣鸡：parting lock t 推杆：push bar 栓打螺丝：S.H.S.B
早睡的好处顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader
水口司:bush 垃圾钉：stop pin 隔片：buffle
弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush
中托边：ejector guide pin 镶针：pin 销子：dowel pin
波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate
斜顶：angle from pin 斜顶杆：angle ejector rod
尼龙拉勾：parting locks 活动臂：lever arm
复位键、提前回杆：early return bar 气阀：valves
斜导边：angle pin 术语：terms
承压平面平衡：parting surface support balance
模排气：parting line venting
回针碰料位：return pin and cavity interference
模总高超出啤机规格：mold ba shut hight背负
顶针碰运水：water line interferes withejector pin
料位出上/下模：part from cavith (core) side
模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.
不准用镶件：Do not u (core/cavity) inrt
用铍铜做镶件：u beryllium copper inrt
初步（正式）模图设计：preliinary (final) mold design
反呵：rever core 弹弓压缩量：spring compresd length
稳定性好：good stability,stable 强度不够：insufficient rigidity
均匀冷却：even cooling 扣模：sticking
热膨胀：thero expansion 公差：tolorance 铜公(电极）：copper electrode 常用塑料英语缩略语[分享]
英文简称英文全称中文全称
ABA Acrylonitrile-butadiene-acrylate 丙烯腈/丁二烯/丙烯酸酯共聚物ABS Acrylonitrile-butadiene-styrene 丙烯腈/丁二烯/苯乙烯共聚物
天长地久歌词AES Acrylonitrile-ethylene-styrene 丙烯腈/乙烯/苯乙烯共聚物
AMMA Acrylonitrile/methyl Methacrylate 丙烯腈/甲基丙烯酸甲酯共聚物ARP Aromatic polyester 聚芳香酯
AS Acrylonitrile-styrene resin 丙烯腈-苯乙烯树脂
ASA Acrylonitrile-styrene-acrylate 丙烯腈/苯乙烯/丙烯酸酯共聚物
CA Cellulo acetate 醋酸纤维塑料
CAB Cellulo acetate butyrate 醋酸-丁酸纤维素塑料
CAP Cellulo acetate propionate 醋酸-丙酸纤维素
CE Cellulo plastics, general 通用纤维素塑料
CF Cresol-formaldehyde 甲酚-甲醛树脂
CMC Carboxymethyl cellulo 羧甲基纤维素
CN Cellulo nitrate 硝酸纤维素
CP Cellulo propionate 丙酸纤维素
CPE Chlorinated polyethylene 氯化聚乙烯
CPVC Chlorinated poly(vinyl chloride) 氯化聚氯乙烯
CS Cain 酪蛋白
CTA Cellulo triacetate 三醋酸纤维素
EC Ethyl cellulo 乙烷纤维素
EMA Ethylene/methacrylic acid 乙烯/甲基丙烯酸共聚物EP Epoxy, epoxide 环氧树脂
EPD Ethylene-propylene-diene 乙烯-丙烯-二烯三元共聚物EPM Ethylene-propylene polymer 乙烯-丙烯共聚物
EPS Expanded polystyrene 发泡聚苯乙烯
ETFE Ethylene-tetrafluoroethylene 乙烯-四氟乙烯共聚物EV A Ethylene/vinyl acetate 乙烯-醋酸乙烯共聚物
EV AL Ethylene-vinyl alcohol 乙烯-乙烯醇共聚物
FEP Perfluoro(ethylene-propylene) 全氟（乙烯-丙烯）塑料FF Furan formaldehyde 呋喃甲醛
HDPE High-density polyethylene plastics 高密度聚乙烯塑料HIPS High impact polystyrene 高冲聚苯乙烯
IPS Impact-resistant polystyrene 耐冲击聚苯乙烯
LCP Liquid crystal polymer 液晶聚合物
LDPE Low-density polyethylene plastics 低密度聚乙烯塑料
LLDPE Linear low-density polyethylene 线性低密聚乙烯
LMDPE Linear medium-density polyethylene 线性中密聚乙烯
零件英语零件类
punch冲头inrt入块(嵌入件) deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子
round punch圆冲子special shape punch异形冲子
三年级家长寄语怎么写
bending block折刀roller滚轴baffle plate挡块
located block定位块supporting block for location 定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆
trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子
guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板
upper holder block上压块upper mid plate上中间板
spring box弹簧箱spring-box eject-rod弹簧箱顶杆
spring-box eject-plate弹簧箱顶板bushing bolck衬套
cover plate盖板guide pad导料块
塑件&模具相关英文
compre sion molding压缩成型flash mold溢流式模具
