Philips Semiconductors
Interconnectivity
D12 SMART
USER’S
MANUAL
TABLE OF CONTENTS
神武天宫
D12 SMART KIT (3)
1.1 Introduction (3)
1.2 Description (3)
1.3 Features (3)
1.4 Operating Environment (3)
润如油膏2.SETTING UP THE D12 SMART KIT (3)
2.1 Connection and System Requirement (3)
感恩的词2.1.1: The D12 Smart Evaluation System (4)
2.1.2: Block Diagram of D12 Smart Board (4)
3.INSTALLATION PROCEDURES (5)
3.1 Installing the software (5)
3.2 Installing the Applet (5)
3.2.1: The icon on the desktop (5)
3.3 Installing the device drivers (5)
3.4 Running the applet (7)
4.DESCRIPTION OF D12 ENDPOINTS (8)
4.1 D12 Endpoints Configuration (8)
4.1.1 Configuration of D12 Endpoints Table (8)
4.2 Operations of D12 Endpoints (8)
节约粮食的故事
4.2.1 Operations of D12 Endpoints Table (8)
5.MISCELLANEOUS (9)
6.DESCRIPTION OF HEADERS (10)
6.1 Header J1 (10)
6.2 Header J2 (10)
6.3 Header J3 (12)
6.4 Header J4 (USB Upstream) (13)
9.PCB PLOTS OF D12 SMART EVALUATION BOARD (16)
10.D12 SMART EVALUATION BOARD (18)
10.1: Enlarged Picture of PDIUSBD12 (18)
11.BILL OF MATERIALS FOR D12 EVALUATION BOARD (19)
D12 SMART KIT
1.1 Introduction
The Philips USB D12 Smart Kit is a comprehensive kit that offers you the full potential of Philips PDIUSBD12 (or D12), in addition to the know-how on how to convert your existing legacy into USB devices. This kit includes the D12 smart boards, test application program (or applet), USB driver, and some sample firmware source codes.
1.2 Description
D12 is a high performance USB interface device that offers DMA transfer capability as well as featur
es for a cost-effective microcontroller-bad system. This kit allows you to thoroughly evaluate the capabilities and features of the device, and provide quick grounding on how to convert your existing non-USB devices such as the digital still camera, mass storage device, and scanner into USB devices.
1.3 Features
无成语The simple design of this kit aims to highlight the features of a USB device. It has the D12 and the 89C738/89C52 microcontroller interfaced to D12. Philips PDIUSBD12 implements all the functions of the USB device, and has an 8-bit parallel data bus for microcontroller interface. The MCU is a member of the 8051-family. The firmware implements all the USB enumeration, D12 Interrupt rvice, power down and resume signaling interfaces. Though the D12 has DMA capability, for simplicity, it is not incorporated in this board. A similar evaluation board, the USB-EPP, has all the DMA features built into it.
With the accompanying applet, you can operate the kit in three modes: Print, Scan, and Loop back modes. The purpo for having the print and scan modes is to allow the evaluation board to emulate either the printer or scanner environment. The Loop back mode is to indicate the integrity of the data when large data packet is nt and received from the host system.
1.4 Operating Environment
Running the kit only requires a new generation PC (motherboard with USB port) with Microsoft Windows 98 operating system. The firmware provided with the kit is written in C language (some Asmbly codes for critical timing), and so allows you to port it to any other platforms for compiling. With this kit, you can develop your USB devices through the firmware and hardware schematics.
2.SETTING UP THE D12 SMART KIT
2.1 Connection and System Requirement
Connect the board to the host system via the USB upstream connector. Follow the instructions on the screen to install the device driver, and then install the software provided with the kit. Ensure that you have the following:
•PC Host system with USB ports;
•Microsoft Windows 98 operating system; and
•D12 smart board, USB cable, and diskette provided with the kit.市调报告怎么写
2.1.1: The D12 Smart Evaluation System
3.INSTALLATION PROCEDURES
洗手间漏水怎么办
3.1 Installing the software
The software includes the firmware, the test application program (or the applet), and the device drivers. The firmware is programmed in the 89C738/89C52 microcontroller (Flash type). If you want to change the firmware or u your own firmware, you just need to reprogram the
89C738/89C52 microcontroller.
3.2 Installing the Applet
1.Inrt the diskette into your disk drive.
2.Copy the file, D12TEST.EXE, contained in the diskette to a directory of your choice -
C:\D12 Smart.
3.Create a shortcut by dragging the file D12TEST.EXE from the directory to the desktop. An
icon similar to Figure 3.2.1 appears.
3.2.1: The icon on the desktop.
3.3 Installing the device drivers
蛋蒸肉When connecting the USB cable to your host system for the first time, a dialog box will appear and prompt you to install the device drivers. Navigate through it and load the device drivers provided in the floppy that comes along with the kit. To install the device drivers:
1.When you connect the USB cable to your host system for the first time, a dialog box
similar to Figure 3.3.1 appears. Click the Next button.
Figure 3.3.1
