Approval Sheet
for
Thick Film Chip Resistor
RL ries
1% 2% 5%
YAGEO CORPORATION
Factory: No.11, Min Chuan Rd., Ta Sheh, Kaohsiung, Taiwan, R.O.C.
word箭头
Tel: 886-7-351-4117 Fax: 886-7-352-6475
Headquarters: 3F, No.233-1, Pao Chiao Rd., Hsin Tien, Taipei, Taiwan,
R.O.C.
Tel: 886-2-2917-7555 Fax: 886-2-2917-4286
晚上盗汗什么原因
w
RL Series Version 2000-3 Page-1
RL Series
Version 2000-3 Page-2
1. SUBJECT : This specification describes of RL ries chip resistors made of YAGEO
Corporation by thick film process.
2. PART NUMBER : Part number of the chip resistor is identified by the ries, size,
tolerance, packing style, temperature coefficient, special type and resistance value.
Example :
RL 1206 F R - 07 0R02
Series Size Resistance Packing Temperature Special Resistance
Name Code Tolerance Style Coefficient Type Value
of Resistance
(1) Size : (unit: inches)
0603=0.063×0.033 1210=0.122×0.102 0805=0.083×0.051 2010=0.197×0.098 1206=0.122×0.063
2512=0.250×0.126
(2) Tolerance : F=±1%, G=±2%, J=±5%
(3) Packaging Style : R =Paper Taping Reel. K =Embosd Plastic Tape Reel. C =Bulk Castte.
(4) T .C .R.: “-“Ba on Spec.
(5) Special Type : 07= 7 inch Dia. Reel
10=10 inch Dia. Reel 13=13 inch Dia. Reel
(6) Resistance Value : 10m Ω、20 m Ω、51 m Ω、100 m Ω、330 m Ω、470 m Ω……
(7) Resistance Series : E24 (E48/96 on request)
RL Series
Version 2000-3 Page-3
3. MARKING :
(1) RL0805/RL1206/RL1210/RL2010/RL2512
Either tolerance in 5% or 1%: 4 digits, us MIL Standard resistance marking. “R” signifies decimal place.
Value =20m Ω
(2) RL0603
Tolerance in 5%: 3 digits, us MIL Standard resistance marking. “R” signifies decimal place.
Value =220m Ω
1% Tolerance : no marking
4. POWER RATING
备战高考
(1) Rated Power at 70°C :
小学游戏
RL0603=1/10W
RL1210=1/3W RL0805=1/8W RL2012=3/4W RL1206=1/4W
写动物的作文RL2512=1W
(2) Rated Voltage : The DC or AC (rms) continuous working voltage corresponding
to the rated power is determined by the following formula : V= √(P X R)
Where V= Continuous rated DC or AC (rms) working voltage (V)
P= Rated power (W) R= Resistance value (Ω
)
5. ELECTRICAL CHARACTERISTICS
STYLE RL0603 RL0805 RL1206 Operating Temp. Range -55°C ~ +125°C
Derated to 0 Load at +125°C
Resistance Range 100mΩ≦Rn<1Ω 20mΩ≦Rn<1Ω 10mΩ≦Rn<1Ω
Temperature Coefficient ±600ppm/°C±1500ppm/°C
STYLE RL1210 RL2010 RL2512 Operating Temp. Range -55°C ~ +125°C
Derated to 0 Load at +125°C
Resistance Range 10mΩ≦Rn<1Ω 10mΩ≦Rn<1Ω 10mΩ≦Rn<1Ω
Temperature Coefficient ±1500ppm/°C
RL Series Version 2000-3 Page-4
周开头的四字成语
请注意英语RL Series
Version 2000-3 Page-5
平衡受体位于
8. ENVIRONMENTAL CHARACTERISTICS
(1) Temperature Coefficient of Resistance (T.C.R.)
Test Method : Measure resistance at +25°C or specified room temperature as
R 1, then measure at -55°C or +125°C respectively as R 2. Determine the temperature coefficient of resistance from the following formula.
R 2－R 1 `
T.C.R.= ----------------- X 106
(PPM/°C) R 1 (t 2－t 1)
Where t 1 =+25°C or specified room temperature
t 2 = -55°C or +125°C test temperature
R 1=resistance at reference temperature in ohms. R 2=resistance at test temperature in ohms.
Acceptance Standard : (Refer to item 5)
(2) Thermal Shock
Test Method : -55±3°C, 2 minutes and +125±2°C, 2 minutes as one cycle. After
5 cycles, the specimen shall be stabilized at room temperature for 1 hour minimum and then measure the resistance to determine △R/R(%).
Acceptance Standard : ±1.0%
(3) Low Temperature Operation
Test Method : Place the specimen in a test chamber maintained at -65 °C. After one hour stabilization at this temperature, full rated working
voltage shall be applied 45 minutes. Have15 minutes after remove the voltage, the specimen shall be removed from the chamber and stabilized at room temperature for 24 hrs. Measure the resistance to determine △R/R(%).
Acceptance Standard : ±1.0%
No mechanical damage.
+5+5 -0 +0+0
-5
+5+5
-0
