模具零件名稱中英文對照一覽表 | ||||||
零件名稱 | ENGLISH NAME | 零件名稱 | ENGLISH NAME | |||
上固定板 | TOP CLAMPING PLATE | 母模仁 | CAVITY | |||
母模板 | CAVITY PLATE | 公模仁 | CORE工商申请 | |||
公模板 | CORE PLATE | 菠菜土豆汤母模入子 | CAVITY INSERT | |||
模腳 | SUPPRORT BLOCK | 母模心子 | CAVITY INSERT PIN | |||
上頂出板 | EJECTOR RET PLATE | 母模替換入子 | CAVITY CHANGEABLE INSERT | |||
下頂出板 | EJECTOR PLATE | 公模入子 | CORE INSERT | |||
下固定板 | BOTTOM CLAMPING PLATE | 公模心子 | CORE INSERT PIN | |||
隔熱板 | THERMAL INSULATING PLATE | 公模替換入子 | CORE CHANGEABLE INSERT | |||
脫料板 | RUNNER STRIPPER PLATE | 滑塊入子 | SLIDE INSERT | |||
母模墊板 | CAVITY SUPPORT PLATE | 滑塊心子 | SLIDE INSERT PIN | |||
公模墊板 | CORE SUPPORT PLATE | 斜銷入子 | Angle LIFTER INSERT | |||
脫料板 | STRIPPER PLATE | 斜銷心子 | Angle LIFTER PIN | |||
流道板 | RUNNER PLATE | 流道開關 | RUNNER SHUT OFF | |||
沙沙美 | 定位環 | LOCATING RING | T 形塊 | T GIB | ||
注口襯套 | SPRUE BUSHNG | U形塊 | U GIB | |||
導柱 | LEADER PIN | 拉料銷 | SPRUE PULLER PIN | |||
導套 | LEADER BUSHING | 定位銷 | DOWEL PIN | |||
頂板導柱 | GUIDE PIN | 頂針 | EJECTOR PIN | |||
頂板導套 | GUIGE BUSHING | 扁銷 | RECTANGLE EJECTOR PIN | |||
大拉杆 | LARGE PULLER PIN | 套筒 | EJECTOR SLEEVE | |||
小拉杆 | SMALL PULLER PIN | 頂出塊 | EJECTOR BLOCK | |||
支撐柱 | SUPPORT PILLAR | 斜銷 | ANGLE LIFTER | |||
定位塊 | INTERLOCKS | pany 斜銷座 | ANGLE LIFTER BASE | |||
定位柱 | LOCATION PILLAR | 引導塊 | GUIDE BLOCK | 乌拉泊 | ||
開閉器(塑膠型) | FRICTIONAL PULLER | O 形環 | O RING | |||
彈簧 | SPRING | 冷卻棒 | THERMAL PIN | |||
運輸板 | PL LOCK | 止水塞 | brass pressure plug | |||
滑塊 | SLIDE | 隔水板 | STRAIGHT BUFFLE | |||
滑塊座 | SLIDE BASE | 水管接頭 | JIFFY TYTE PLUG | |||
滑軌 | SLIDE RAIL | 油封 | OIL SEAL | |||
后跟塊 | HELL BLOCK | 內六角螺釘 | SOCKET HEAD CAP SCREW | |||
耐磨板 | WEAR BLOCK | 等高螺釘 | SOCKET HEAD STRIPPER BOLT | |||
壓板 | RAIL | 吊模螺絲 | EYE BOLT | |||
限位塊 | STOP BLOCK 有关月亮的诗 | 吊環 | SAFETY HOIST RINGS | |||
定位夾 | SLIDE RETAINER | 彈簧墊圈 | SPRING WASHER | |||
定位珠 | SLIDE RETAINER | 加長型水管接頭 | EXTENSION JIFFY TYTE PLUG | |||
急回機構 | POSITIVE EARLY EJECTOR RETURN | 未注尺寸請參考 3D MOLDEL: | DON’T MEASURE PLEASE REF 3D MODEL | |||
急回推杆 | LEVER | 入子孔單邊向外 補正0.005MM﹕ | INSERT HOLE'S TOLERANCE IS +0.005MM | |||
固定塊 | MOUNT AND COVER PLATE | 入子外形單邊向內 補正0.005MM﹕ | INSERT SHAPE'S TOLERANCE IS -0.005MM | |||
彈簧片 | ARM | 全周﹕ | AROUND | |||
熱處理 | HEAT TREATMENT | 0度起點 | 0ْ START POINT | |||
表面氮化 | SURFACE NITROGENIZED | 斜度轉折點 | ANGLE CHANGING POINT | |||
上限 | UPPER VALUER | 保持 | KEEP | |||
下限 | LOWER VALUER | 注口中心線 | SPRUE CENTER LINE | |||
插破 | SHUT OFF | 模具中心線 | MOLD CENTER LINE | |||
靠破 | SITTING | 人事变动通知 | 咬花面 | TEXTURED SURFACE | ||
油溝槽深 | GREASE GROVER | 拔模角 | DRAFT ANGLE | |||
本文发布于:2023-06-24 21:02:06，感谢您对本站的认可！
本文链接：https://www.wtabcd.cn/fanwen/fan/89/1053278.html
版权声明：本站内容均来自互联网，仅供演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系，我们将在24小时内删除。
| 留言与评论（共有 0 条评论） |
