总装车间Australian Standard®
澳大利亚标准®
Fixed platforms, walkways, stairways and ladders — Design, construction and installation固定平台、走道、楼梯与梯子的设计、施工与安装
This Australian Standard was prepared by Committee SF/13, Platforms, Gangways, Stairways and Ladders. It was approved on behalf of the Council of Standards Australia on 9 September 1992 and published on 16 November 1992.
本《澳大利亚标准》是由SF/13平台、通道、楼梯与梯子委员会编制的。1992年9月经澳大利亚标准委员会通过，1992年11月16日出版。
The following interests are reprented on Committee SF/13:
SF/13委员会由以下单位参加：
Aluminium Development Council
铝业发展委员会
桃花花语Bureau of Steel Manufacturers of Australia
澳大利亚钢铁制造局
Confederation of Australian Industry
澳大利亚工业联合会
Department of Employment, Vocational Education, Training and Industrial Relations, Qld
昆士兰州就业、职业教育、培训与劳资关系部
Department of Labour and Industry, Tas.
塔斯马尼亚州劳工部
Master Builders
建筑商协会
Construction and Housing Association of Australia
澳大利亚建筑与住房协会
朝辞白帝彩云间全诗
Pacific Power
太平洋电力公司
Public Works Department, N.S.W.
新南威尔士州公共工程部
Royal Australian Institute of Architects
皇家澳大利亚建筑师协会
Water Board, Sydney-Illawarra-Blue Mountains
水理事会，悉尼-伊拉瓦拉-蓝山流域
WorkCover Authority of New South Wales
新南威尔州工伤保险局
Review ofAustralian Standards. To keep abreast ofprogress in industry, Australian Standards are subject to periodic review and are kept up to date by the issue of amendments or new editions as necessary. It is important therefore that Standards urs ensure that they are in posssion of the latest edition, and any amendments thereto.
澳大利亚标准的评审。为了保持标准与工业发展同步，澳大利亚标准需要定期进行评审并发布修订本，必要时出版新的版本以保持更新。因此，标准使用者使用的版本必须是最新版本，同时需要使用所有修正版本的内容。
Full details of all Australian Standards and related publications will be found in the Standards Australia Catalogue of Publications; this information is supplemented each month by the magazine ‘The Australian Standard’, which subscribing members receive, and which gives details of new publications, new editions and amendments, and of withdrawn Standards.
彩铅图片
澳大利亚标准局出版的《标准目录》收集了所有澳大利亚标准的详细信息和相应出版物，此信息每月在杂志《澳大利亚标准》上进行补充说明，已订阅会员会收到此杂志，另外该杂志还会介绍新出版物、新版本和修订本以及废止标准的详细信息。芹菜炒香肠
Suggestions for improvements to Australian Standards, addresd to the head office of Standards Australia, are welcomed. Notification of any inaccuracy or ambiguity found in an Australian Standard should be made without delay in order that the matter may be investigated and appropriate action taken.
我们欢迎提出有关改进澳大利亚标准方面的建议，欢迎写信到澳大利亚标准局。如发现澳大利亚标准存在任何不准确或含糊不清的内容，请及时告诉我们以便我们做出调查并采取适当措施。
This Standard was issued in draft form for comment as DR 90065.
本《标准》作为DR 90065草案发布，以征求意见。
Australian Standard®
澳大利亚标准®
Fixed platforms, walkways, stairways and ladders — Design, construction and installation固定平台、走道、楼梯与梯子的设计、施工与安装
First published as AS CA10-1938. 首次刊印作为AS CA 10-1938 Second edition 1963. Third edition 1966. Fourth edition 1971 第二版1963年，第三版1966年，第四版1971年 . Revid and redesignated AS 1657-1974. 修订并重新命名为AS 1657-1974 Second edition 1985. Third edition 1992. 第二版1985年，第三版1992年 |
|
PUBLISHED BY STANDARDS AUSTRALIA (STANDARDS ASSOCIATION OF AUSTRALIA) 1 THE CRESCENT, HOMEBUSH, NSW 2140
澳大利亚标准局（澳大利亚标准协会）出版
地址：1 THE CRESCENT, HOMEBUSH, NSW 2140
PREFACE
序言
This Standard was prepared by the Standards Australia Committee on Platforms, Gangways, Stairways and Ladders, to superde AS 1657-1985.
本《标准》由平台、通道、楼梯和梯子澳大利亚标准委员会编制，取代AS 1657-1985标准。
Changes to the Standard include —
本《标准》做出的修改包括-
(a)reducing the minimum wall thickness of steel piping which may be ud;
降低了可能使用的钢管的最小壁厚。
(b)incorporating a minimum tensile yield stress requirement for aluminium alloys;
加入对铝合金最小拉伸屈服应力的要求。
(c)显微镜的结构图deleting references to specific aluminium alloys and tempers;
删去对特定新回忆社区铝合金及调和物的引述。
(d)updating the dimensions of steel ctions other than piping, to reflect current manufacturing practices; and
根据现行有效的制造规范，更新除钢堤防工程管外的型钢尺寸以及
(e)provision of test methods to determine the integrity of guardrail systems, and the stren
gth of the connection between guardrail posts and the supporting structure.
规定了测定护栏系统完整性以及护栏立柱与支撑结构之间连接强度的方法。
© Copyright STANDARDS AUSTRALIA
版权归澳大利亚标准局
Urs of Standards are reminded that copyright subsists in all Standards Australia publications and software. Except where the Copyright Act allows and except where provided for below no publications or software produced by Standards Australia may be reproduced, stored in a retrieval system in any form or transmitted by any means without prior permission in writing from Standards Australia. Permission may be conditional on an appropriate royalty payment. Requests for permission and information on commercial software royalties should be directed to the head office of Standards Australia.
