LN3--PU/Phylon/Rubber Process
Contents for the three ctions of English Version PFC:
∙ Phylon Work Sheet PH数据表
∙ Components Specification Sheet(Phylon) 部件明细单(Phylon)
秋天喝什么汤最好
∙ Component Specification Sheet Set Up(Phylon) (此部分无中文)
∙ Phylon Midsole Specifications PH全插规格
∙ Phylon Preform Specifications PH粗胚规格
∙ Preform Drawing 粗胚图
∙ Component Specification Sheet Set Up(PU) (此部分无中文)
∙ PU Midsole Specifications PU全插规格
∙ PU Midsole Specifications II PU数据表
∙ Components Specification Sheet(PU) 部件明细单(PU)
∙ PU Midsole Pouring Specification PU灌注明细
∙ Outsole Color Schedule 本底颜色明细
∙ Outsole Preform Specifications 本底粗胚规格
假如给我三天光明读后感600字
∙ Outsole Pressing Process 本底压制流程
∙ Outsole Degreasing Process 本底水洗流程
*********************************************************************
PU Section PU部分
*********************************************************************
air bag schedule 空 气袋分段
specific instructions 特别说明
air bag diagram 空气袋图示
hardness(skin on) 硬度（带皮）
density 密度
elongation 延伸率
tear 撕力
tensile 拉力
split tear 撕裂
painting 喷漆
MCS number 材料编号
mold relea agent 脱模剂
polyurethane 聚安脂
polyester 聚脂
Density must be within NIKE spec and follow weight chart 密度必须符合NIKE要求及重量表
No dirty midsole sidewalls yellowing or poor cosmetics due to mold condition.
无因模具造成的边墙黄变及外观不良。
Correct molded or painted colors per NIKE confirmation.
根据NIKE的确认，成型材料及喷漆颜色正确。
Correct top/bottom edge trimming within 1mm width allowance.
正确修边上部及底部边缘，允许1mm余量。
No larger than 5mm diameter internal air voids.(checked by light table)
内部气泡直径不可大于5mm(用照明桌查看)
最简单鉴定银子的方法
No pin holes on cosmetic area larger than 1mm in diameter.
外观无直径大于1mm的针孔。
Adequate anti yellowing white paint applied to pass NIKE yellowing test.
用合适的耐黄变白漆通过NIKE耐黄 变测试。
No over spraying of paint into bonding areas and/or below cosmetic boundaries.
喷漆不得过量，碰到粘合处或到外观边缘下面。
All airbags should not have expod areas on the component bottom, and no voids larger than 15mm diameter are allowed for all airbags on top area. Any voids in coverage should be filled and buffed.
在部件底部不得有空气袋外露，空气袋上部不得有大于15mm的空洞，上部的任何空洞都要补上磨平。
Visible airbags should not have visible centerlines twisted by window plugs.
空 气袋窗口不得因窗口塞而使中心线扭曲。
Correct visible window depth margin of both sides.
两边空气袋外露深度一致。
Visible airbag plugs should be cleaned to remove/relea flashing that caus margin cosmetic problems.
外露窗口塞要保持干净，有边料要清除，以免引起外观问题。
Visible airbag weld tips that protrude through the PU side wall must not exceed 1mm width, and paint must cover the to avoid visibility.
可见的空气袋接头伸入PU边墙不可超过1mm宽，而且上面要喷漆以免影响外观
Excess mold relea on mold/bottom plates should be removed to avoid poor bonding surfaces on the component.
模板上过多的脱模剂要清理干净，以免造成部件表面粘着不良。
证券包括哪些种类PU color marbling specs are per confirmed allowance samples.
PU颜色按确认的样品。
Any skinning of PU on top/bottom of midsole must be buffed off, no side skinning allowed.
上下PU脱皮要磨去，两侧不可有脱皮。
Correct Hardness in confirmed checking area.
在确认的检验部位，硬度正确。
inspection specification 检验说明
pouring position 灌注部位
stationary 固定性
mobility 流动性
toe to heel/heel to toe 从前掌到后跟/从后跟到前掌
mold angle 模具斜度孟子被尊称为
air bag diagram 空气袋图示
forefoot air bag schedule 前掌空气袋分段
heel air bag schedule 后跟空气袋分段
polyester 聚脂
anti-yellowing painting 喷耐黄 变漆
PU pouring process PU灌注流程
closing the mold 盖模
going through heat oven/heat channel 过烘箱
opening the mold 开 模
demolding 画鞋子简笔画脱模
vent hole 排气孔
take out finished products 取成品
remove flashing 清边料
spray relea agent 喷离型剂
blow by air gun 吹气
儒林外史阅读笔记wipe relea evenly 擦离型剂
put in airbag 放空气袋
press the middle plate 压中框
pour per tting time and pour into hole around fore-airbag 依正确秒数灌注，原料需注入BAG前端孔内
action must be brisk 动作宜轻宜快
open the top plate first ,then removable middle plate
先将上盖架起，再将活 动小中框打开
Pull PH out by heel parallel with air bag window plug, report immediately if any mold problem, PU rotten or stick to the mold and lack of material. 用手抓PH后跟，用力方向与窗口塞平行，发现模具不良，烂料，粘模,失 肉立即反映。
against the direction of vulcanizing line 逆着硫化线方向
using bamboo tools 使用竹制工具
Ensure the PH part size must be the same as mold, reject the defect PH part 注意PH号码与模具号码一致，剔除不良品
Exactly inrt the airbag to fit mold window plug, left window first, then clo the middle plate.
将PH确实钩入窗口塞，先将左边窗口钩入再放下中框
Press the airbag to fit mold window plug with clean gloves on.
戴干净手套，将BAG确实压好，保持BAG与窗口塞吻合
PU process after de-molding PU脱模后处理流程
marking the production date 写记号
quality inspection 质检
mending 修补
removing the blow-by 洗溢料
100% inspection 全检
packing mac的快捷键包装
