软管CONDUIT | 公制螺纹管接头 CONNECTOR WITH METRIC THREAD | ||||
标称内径 nominal width NW | 内径 Inside ø nominal | 螺纹规格 Thread size | 内径 Inside diameter mm (nom.) ID | ||
标准 standard | 公制metric | 金属螺纹 metal thread | 聚酰胺螺纹polyamide thread | ||
07 | 10 | 6.2 | M10 | - | - |
10 | 12 | 9.6 | M12 | 5.7 | 8.0 |
10 | 12 | 9.6 | M16 | - | 11.0 |
12 | 16 | 12.0 | M16 | 9.7 | 11.0 小姨的朋友 |
17 | 20 | 16.2 | M20 | 13.7 | 14.6 |
23 | 25 | 22.6 | M25 | 18.6 | 19.0 |
29 | 32 | 29.0 | M32 | 25.7 | 26.0 |
36 | 40 | 36.5 | M40 | 33.4 | 32.0 |
48 | 50 | 47.5 | M50 | 42.7 | 42.0 |
48 | 50 | 47.5 | M63 | 54.0 | 53.0 |
软管CONDUIT | PG制螺纹管接头 CONNECTOR WITH PG THREAD | ||||
标称内径nominal width NW | 内径 Inside ø nominal | 螺纹规格 | 内径 Inside diameter mm (nom.) ID | ||
标准 standard | 公制metric | Thread size | 金属螺纹metal thread | 聚酰胺螺纹polyamide thread | |
07 | 10 | 6.2 | 社会竞争力PG07 | - | 8.0 |
10 | 12 | 9.6 | PG09 | 9.5 | 10.0 |
12 | 16 | 12.0 | PG11 | 12.5 | 13.0 |
- | - | - | PG13.5 | 14.5 | 14.5 |
17 | 20 | 16.2 | PG16 | 16.5 | 17.5 |
23 | 25 | 22.6 | PG21 | 22.5 | 22.5 |
29 | 32 | 29.0 | PG29 | 斯诺克摆球图片30.5 | 30.5 |
36 | 40 | 36.5 | PG36 | 40.5 | 37.5 |
- | - | 篮球体能训练- | PG42 | - | 48.0 |
48 | 50 | 47.5 | PG48 | 52.0 | 50.0 |
1. | 使用PMACUT 剪切工具剪切软管，剪切面与软管轴心垂直。 | Straight cut with PMA Cutting tool PMACUT, 90o to the conduit axis. | |
2. | 管卡已预先安装，推入时轻微转动直至不能推入为止。 | The retaining clip is pre-mounted. Push in with a slight twist until the stop. | |
3. | 轻微回拉软管，确保锁紧。 | Pull back slightly to ensure the locking mechanism is fully engaged. | |
4. | 在振动或相似情况下的应用建议：为保护螺纹最好使用密封胶或黏合剂。（如：Loctite） | Recommendation for applications under vibrations or similar: Protect threads with commercial adhesive or al compound (e.g. Loctite). | |
5. | 安装管接头的软管部分不要弯曲，如果定位请使用管夹或其他支撑。 | Do not bend off the PMAFLEX conduit directly after the connector. If necessary destine the direction with a system support or similar. | |
6. | 为安全起见： 需用螺丝刀才能开启管夹。 | For safety reasons: To re-open a screwdriver has to be ud. | |
1. | 使用PMACUT 剪切工具剪切软管，剪切面与软管轴心垂直。 | Straight cut with PMA Cutting tool PMACUT, 90o to the conduit axis. | |
2. | 软管－密封套－管接头管夹－O 型环或垫圈 | Conduit – Seal Cap – Connector - Oval Clip – Flat Gasket or O-ring | |
3. | 将密封套安装于软管末端， 根据IEC529/EN60529 标准， 防护等级可达IP68 。 | 笔记本电脑多少瓦 | Push al cap onto end of conduit to achieve an ingress protection up to IP68 according to IEC 529 / EN 60529. |
4. | 为安装方便， 密封套可使用水或润滑剂来润滑。 | For ea of installation moisten al cap with water or lubricant. | |
5. 鹅的组词 | 将带密封套的软管完全推进接头。（如果密封套没有完全安装好，管卡将不能安装） | Push conduit with al cap with slight twist fully into connector. (For safety reasons, retaining clip will not fit if al cap is not fully installed.) | |
6. | 推进管卡直至完全配合。（确保管卡缺口部位在软管侧） | Push in the Retaining Oval Clip until the barbed hooks are optimal t. (Ensure that the opening slot of the retaining clip is on conduit side) | |
7. | 在振动或相似情况下的应用建议：为保护螺纹最好使用密封胶或黏合剂。（如：Loctite） | Recommendation for applications under vibrations or similar: Protect threads with commercial adhesive or al compound (e.g. Loctite). | |
8. | 安装接头的软管部分不要弯曲， 如果定位请使用管夹或其他支撑。 | Do not bend off the PMAFLEX conduit directly after the fitting. If necessary destine the direction with a system support or similar. | |
9. | 为安全起见： 需用螺丝刀才能开启管夹。 | For safety reasons: To re-open a screwdriver has to be ud. | |
本文发布于:2023-06-18 09:36:51，感谢您对本站的认可！
本文链接：https://www.wtabcd.cn/fanwen/fan/89/1043818.html
版权声明：本站内容均来自互联网，仅供演示用，请勿用于商业和其他非法用途。如果侵犯了您的权益请与我们联系，我们将在24小时内删除。
| 留言与评论（共有 0 条评论） |
