"A"
A Asmbly总成
A.R.B Anti Roll Bar横向稳定杆
A/C Air Conditioning空调
A/F Air Fuel Ratio空气燃料混合比
A/RST Armrest扶手
A/RTL Anti Rattle防震
A/T Automatic Transmission自动变速器
AA Architecture Approval结构批准
AAM Alliance of Automobile Manufactures汽车制造商联盟
ABAG Airbag气囊
ABC Active Body Control车身主动控制系统
ABIW Architectural Body In White白车身结构
ABIWM Architecture Body in White Mule Mule车白车身结构
A-BOM Analytical Bill of Material A－BOM
ABPR ABS Pump Request防抱制动系统泵作用
ABS Anti-lock Brake System or Anti-Block Steering防抱死制动系统
ABSL Absolute绝对的
ABSL ABS Lamp防抱制动系统警告灯ABSR ABS Relay防抱制动系统继电器ABSS ABS Stop防抱制动系统停止
ABUT Abutment对接、邻接
AC Architecture Confirmation结构确认
代表健康的字
AC Architecture Criteria结构标准
水硬性
ACC Air Condition Clutch空调离合器
ACC Activated Carbon Canister活性碳罐
ACC Accept允收
ACC Access通道，住处存取（软件名）ACC Architecture Configuration Complete结构配置完成
ACCEL Accelerator加速
ACCL A/C Clutch 空调机离合器
ACCUM Accumulator储能器，储压器
ACD Actual Completion Date实际完成数据
ACE Advanced Concept Engineering先期概念工程
ACEV A/C Evaporate Temperature空调机蒸发温度
ACI Automatic car identification system汽车自动识别系统
ACL Air Cleaner空气滤清器
ACMD Accommodate调节
ACSRY Accessory附件
ACST A/C Status 空调机状态
ACSTC Acoustic阻尼
明月天ACSW A/C Press Switch 空调机压力开关
ACT Air Charge Temperature进气温度
ACTR Actuator执行器
AD Alternatives Development选择性开发
ADEL Air Delivery Mode 空气传送模式
ADH Adhesive粘合剂
ADJ Adjust调节
ADJMT Adjustment调节
ADM Absolute Dimension Measure全尺寸测量
ADPR Adaptor转接器
ADT Architecture Development Team结构开发小组
ADV Analysis / Development / Validation分析/开发/验证
ADVMS/PQMS Analysis Development Validation Management System /
Performance & Quality Management System 分析开发验证管理系统/性能&质量管理系统
AE Application Engineer应用工程师
AFC Air Flow Control空气流量控制AFLO Air Flow空气流量计
AFMA Actual Force Motor Amplifier实际强力马达放大器AFS Air Flow Sensor空气流量传感器AFUE Average Fuel Switch平均油耗开关
AFV Alternative Fuel Vehicle代用燃料汽车
AGR Actual Gear实际档位
AGV Automatic Guided Vehicle自动导向车辆
AHTY Ashtray烟灰缸
AI Air Injection二次空气喷射
AIAG Automotive Industry Action Group汽车工业行为组织
AIGN ABS Ignition Volts防锁刹车系统点火电压
AIRC Air Control 空气控制
AIRD Air Delivery Mode空气传送模
AIS Air Induction System二次喷气装置
AIV Air Injection Valve空气喷射阀
ALBS Automated Line Balance System-Sequence of asmbly estab自动化流水线平衡系统—工业工程建立的装配次序ALCL Asmbly Line Communication Link总装线测试插座
ALDL Asmbly Line Diagnostic Link组装线通信线路
ALIAS Styling Software Brand Name ALIAS（软件）
ALM Alarm警报
ALR Automatic Lock Return自动馈回缩器
ALT Alternator交流发电机
ALT Altitude Switch 海拔高度开关
ALY Alloy铝合金
AM Ante Meridian上午
AM Architecture Mule Mule车结构
AMB Ambient环境
AMBR Architecture Mule Build Readiness Review Mule车结构试制评估准备就绪
AMP Amperes电流强度
AMPF Amplifier放大器
AMT Armature电枢
AMT Automated Manual Transmission 自动手动传动
ANC Anchor固定点
ANC/L Ancillary辅助
ANRM Architecture Non-Running Mule Mule车结构（无法开动）
ANSI American National Standards Institute美国国家标准协会
ANT Antenna天线
AOQ Average Output Quality平均出厂品质
感冒能刮痧吗AP Accelerator Pedal加速踏板
AP Advanced Purchasing先期采购
APC Aperture card穿孔卡片
APD Approved Product Description批准的产品描述
APE Annual Program Execution年度项目执行
APEAL Auto Performance Execution and Layout汽车性能执行和规划
APEC Asia Pacific Economic Cooperation亚太经济联盟
APET Advanced Program Execution Team先期项目执行小组
APLQ Applique饰件
APM Assistant Program Manager助理项目经理
APO Asian and Pacific Operations亚太地区业务
APP Approve核准，认可，承认
APPROX Approximately大约，近似
APQP Advanced Product Quality Planning先期产品质量策划
APRL Air Pump Relay 空气泵继电器
APRTG Aspirating除尘
APRTL Area Peer Review Topic List同等区域主题评估表
APS Absolute Pressure Sensor绝对压力传感器
APTR Aperture孔径
APV All Purpo Vehicle多用途车辆
AQL Acceptable Quality Level运作类允收品质水准
AR Appropriation Request经费要求
AR Averary Range全距平均值
ARA Appropriations Request Approved批准的拨款申请
ARB Anti Roll Bar横向稳定杆
ARC Arch罩
Arch.Architecture结构
AREQ A/C Request 空调机作用
ARL Aerial天线
ARM Architecture Running Mule Mule车结构（可开动）
ARP Appropriations Request Process拨款申请流程
ARYM Aerodynamic空气动力学的
ASB Automotive Strategy Board汽车战略委员会
ASC Architecture Selection Complete结构选择完成
ASE Automotive Safety Engineering汽车安全工程
ASE Aftersales Engineering售后工程
德国室内设计ASI Architecture Studies Initiation结构研究开始
ASQ&R Advanced Supplier Quality & Readiness先期供应商质量&准备就绪
ASR Acceleration Slip Regulation汽车驱动防滑控制系统
ASR Automatic Stability Regulation自动稳定调节
ASRC Automatic Stability Regulation Controller自动稳定调节控制器
ASRS ASR Switch自动稳定调节控制器开关
ASSI Architecture Statement of Strategic Intent战略意图的结构状态
ASST Assistant辅助(设备)
ASSY Asmbly总成
ATCU Auto Condition Control Unit自动空调控制单元
ATDC After Top Dead Center到上止点后
ATF Automatic Transmission Fluid自动变速箱油液
ATS Architecture Technical Specification结构技术规范
ATS Air Temperature Sensor空气温度传感器
ATT Attachment附件
ATV Advance Technology Vehicle高科技车辆
ATV Active活动
AUD Audio声频的
AUDL Auto Door Locks 自动门锁
AUX Auxiliary辅助装置
AVD Advanced Vehicle Development先期车辆开发
AVDC Advance Vehicle Development Center先期车辆开发中心
AVDP Advanced Vehicle Development Process (Time between
先期车辆开发流程（在DSI与VPI之间）DSI and VPI)
AVPM Advanced Vehicle Planning Manager先期车辆计划经理
AWD All wheel Drive全轮驱动
AWL ABS Warning Light防锁刹车系统警示灯
AXL Axle桥，轴
"B"
B+Battery Positive Voltage蓄电池正极
B Build试制
B/HD Bulkhead防水壁
B/SD Bodyside车身侧部
B+U Build + Utilities土建动能
BAD Build Authorization Document试制授权文档
BAD Badge标牌
BAL Balance平衡
BALAST Balast整流器
BAR Barrel桶形
BARO Barometric Pressure大气压力
BAROS Barometric Pressure Sensor大气压力传感器
岭上开遍映山红
BARV Barometric Pressure Voltage 大气压力电压
BAT Battery电瓶
BATT Battery Volts 电瓶电压
BBS Bulletin Board System报告模板系统
BBW Brake By Wire汽车电制动系统
BCR BOM Change Request零件清单更改申请
BCU Body Control Unit车身控制单元
BD Body车身
BDC Bottom Dead Center下止点
BE Body and Exterior Department车身外饰部
BEB Body Section车身科
BEC Closure Section门盖科
BEE Exterior Section外饰科
BEI Body-In-White, Exteriors & Interiors白车身，内部和外部
BELT Seat Belt Telltale 安全带显示器
BER Bearing支座
BFL Baffle导流板
BGAM Burglar Alarm防盗警报
BGT Bright光亮的
BHP Brake Hor Power制动热效率
BIF Batch Implementation Freeze批量执行冻结
BIR Prototype Build Issue Report试制问题报告
BIR Build Issues Resolution试制问题
BIR Build Incident Report装车问题报告
BIS Best In Segment最佳分割
BIW Body-In-White白车身
BK Back后板
授权书
BKLG Backlight后灯
BKUT Backout拆除
BL Ball球
BLA Blade片
BLCK Block盖板
BLD Bleed排气，排放
BLN Blend混合
BLNK Blanking盖板
BLO Blower送风
BLT Belt带
BMEP Brake Mean Effective Pressure空燃比
BNC Bench长条座椅
BND Band带
BNT Bonnet发动机罩
BOA Bill of Architecture结构表
BOD Bill Of Design设计清单
BOE Bill of Equipment设备清单
BOF Body On Frame车身框架
BOI Ba Oil Interchanger基础油互换
BOL Bill Of Lading提单
BOLS Bolster枕座
BOM Bill of Material物料清单
Bom View Bill of Materials View 产品明细表视图Bom View Revision Bill of Materials View Revision产品明细表视图版本BOP Bill Of Process工艺清单
BP Basis Point基点
BP Business plan业务计划
BPR Bumper保险杠
BR Brace拉杆，撑臂
BRD Braid编织物
BRK Brake制动
BRKT Bracket支架
BROCH Brochure册子
BRT Ball Rust Tes球腐蚀试验
BS Ba基本的
BSCT Bacoat底漆
BSD Build Site Direction试制现场指导书BSFC Brake Specific Fuel Consumption制动油耗率
BT Boot后备箱，护罩BTDC Before Top Dead Center上止点前
BTHR Breather通风
BTM Bottom底部
BTN Button按钮
BTU British Thermal Units英热单位
BTW Between之间
BUG Burglar防窃
BUH Bush衬套
BYP Bypass旁通
BZL Bezel玻璃嵌框
"C"
C&M Care and maintenance 维修及保养
C.CARB Conventional carburetor常规化油器
C.P.Car park(停)车场我的下一站
C/FBR Carbon Fibre碳纤维
C/MBR Crossmember横梁
C/O Carry over携带
C/S Concept Sheet概念表
CAB Change Approval Board 更改审批会
CAB Curtain Airbag 侧面气帘
CAC Corporate Advisory Council联合顾问委员会
CAC Charge Air Cooler增压中冷器
CAD Computer Aided Design计算机辅助设计
CADAM Computer Augmented Design and Manufacturing计算机辅助设计及制造
CAE Computer Aided Engineering计算机辅助工程
CAF Cubing Assurance Fixture(Interiors Only)空间保证装置（只限内部）CAFE Corporate Average Fuel Economy公司平均燃油经济性
CALN Calibration校准
CAM Computer-Aided Manufacturing计算机辅助制造
CAMI Canadian Automotive Manufacturing,Inc.加拿大汽车制造有限公司CAR Corrective action request改正行动要求
CARB Carburetor化油器
CARE Corporate average regulated emission公司规定的平均有害物排放量CARE Customer Acceptance Review and Evaluation用户接受度和审查评估CARP Cooperate automotive rearch program 汽车合作研究程序
CARR Carrier运载工具，载体
CARR Carriage车溜板
CART Carton 卡片纸
CASG Casing蒙皮
CAT Catalytic Converter触酶转换器
CAT Carburetor air temperature化油器空气温度
CAV Cavity模穴
CBC Costbook control成本控制
CBL Cable电缆
CBR Costbook relea发布第一版costbook
CC Carbon Copy副本复印相关人员
CC Change Control更改控制
CCB Cross Car Beam仪表板横梁
CCC Converter Clutch Control转换离合器控制
CCD Combustion Chamber Deposit燃烧室沉积
CCP Collaborative Criteria Process合作的标准流程
CCS Cold Cranking Simulator冷启动模拟器
CCS Crui Control System汽车巡航控制系统
CDB Corporate Data Ba公司数据库
CDI Central Multiport fuel Injection 中央多点燃油喷射
CDLS Common Datum Locating Strategy The purpo is to
provide vehicle technical direction for integrating
product(BOM) and process(BOP) at system interfaces to
achieve designs/process that are innsitive to variation.
The asmbly quence, component break up, and
product/process design enablers(slip planes, mating
surfaces, clearances, interfaces, joint design) provide
“how” the vehicle, major sub-systems, asmblies, sub-
asmblies and/or parts will be designed at interfaces for
control of variation. In esnce, “how to” design the tools
公共信息配置策略
CE Cost Estimator成本评估者
CE Chief Engineer总工程师
CEIT Central Engineering Improvement Team主要的工程改进小组CES Clutch Engage Switch离合器接合开关CFC Chlorofluorocarbon氯氟碳化合物
CFI Central Fuel Injection中央燃油喷射
CFIT Cross Functional Implementation Team跨功能执行小组CFPP Cold Filter Plugging Point冷滤点
CFRC Carbon fiber friction material碳纤维摩擦材料CFRP Carbon fiber reinforced plastic碳纤维强化塑料CGLG Ciger Lighter点烟器
CGS Computer Graphics System计算机图形系统
CH Chassis Department底盘部
CHA Advanced Engineering Section前期工程科
CHAN Channel通道
CHARCAN Charcoal Chanister碳罐
